NAVY MIL-P-15742 C-1988 PLUGS PLASTIC (HEAT-EXCHANGER-TUBE)《(热交换管)塑胶插头》.pdf
《NAVY MIL-P-15742 C-1988 PLUGS PLASTIC (HEAT-EXCHANGER-TUBE)《(热交换管)塑胶插头》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-15742 C-1988 PLUGS PLASTIC (HEAT-EXCHANGER-TUBE)《(热交换管)塑胶插头》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、(fNCH-POUNOI MIL-P-15742C - SUPERSEDING MIL-P-157428 20 February 1973 (See 6.5) MILITARY SPECIFICATION PLUGS, PLASTIC (HJUT-EXC“GER-TUBE) This specification is approved for us8 by all Departments 8nd Agencies of the Department of Defense. 1. SCOPE 1.1 ScoDe. This specification covets heat-exchanget-
2、tube plugs which are driven into both ends of leaking condenser or other heat-exchanger-tubes to prevent contamination of the fluid surrounding the tubes. 1.2 ClassffLcstioa. Plugs covered by this specification shall be designated in the followfng form (see 6.2 and 6.3): Military part nube Size code
3、 number (see 1.2.1) 1.2.1 Size c ode number. single-digft number (see table I). The size of the plug (see 3.3) is identified by a I I Beneficial comments (recommendations, additions, deletfons) and any pertinent data which may be of use in improving this document should be addressed.to: Commander, N
4、aval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardlzatfon Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 4730 PISTRTRUTT ON STATMENT 4 . Approved for publiZ relea2;-
5、 distribution is unlidted. Infomution Wandling Ssvics, Mo6m ISSUE 93-01. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-LS742C Y7 9 9999906 02721ii5 9 I HIL-P-15742C TABLE I. r 2 3 4 5 6 I l 2, APPLICABLE DOCUMENTS 2.1 Cwerment d ocument S. 2.
6、1.1 8Decifications and standarda . The following specifications and standards form a part of this docunent to the extent specified herein. otherwfse specified, the issues of these documents are those listed in the Issue of the Department of Defense Index of Specifications and Standards (DoDISS) and
7、supplement thereto, cited in the solicitation (see 6.2). Unless SPECIFICATIONS FEDERAL PPP-B-566 - Boxes, Folding, Paperboard; PPP-B-636 - Boxes, Shipping, Fiberboard. MILITARY MIL-P-116 . - Preservation, Methods of. STANDARDS FEDERAL FED-STD-406 - Plastics: Methods of Testing. MILITARY MIL-STD-105
8、- Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage. Attributes. (Unless otherwise indicated, copies of federal and military specifications and standards are available from the Naval Publications and Forms Center (ATTN: NPODS), 5801 Tabor Avenue, Philade
9、lphia, PA 19120-5099.) 2.2 Non-Government I) ublicationg . The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. documen
10、ts not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, the issues of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NATIONAL MOTOR FREIGHT TAFFIC ASSOCIATION, INC., AGENT Nation
11、al Kotor Freight ClasaificatSon (Application for copies ihould be addressed to the National Kotor Freight Traffic Association, Inc., ATA TRAFFIC Dept., 2200 Hl11 Road, Alexandria, VA 22314. ) UNIFRM CLASSIFICATION COMHITTEE AGENT Uniform Freight Clasrification Ratingi, Rules and Regulations (Applica
12、tion for copies should be addressed to ths Uniform Classification Committse Agent, Tariff Publication Officer, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606.) (Non-Covernment standards and other publicatfons are normally available from These documents also the organizations that prepare or
13、 distribute the docmento. may be available in or through libraries or other informational mewices.) 2.3 grder af sec edenc e. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence, Nothing in this document, however, s
14、upersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Hat erial, . Plugs shall be made of laminated phenolic-material, consisting of layers of cotton fabric impregnated with natural-color phenolic resin and pressed under controlled conditions of
15、 temperature and pressure. 3.1.1 Recovered materials. Unless otherwise specified herein, all material incorporated in the products covered by this opacification shall be new and may be fabricated using materials produced from recovered materials to the maximum extend practicable without jeopardizing
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP15742C1988PLUGSPLASTICHEATEXCHANGERTUBE 热交换 塑胶 插头 PDF

链接地址:http://www.mydoc123.com/p-980538.html