NAVY MIL-O-24926 A-1990 OVERCOAT WOMAN-S ENLISTED《女式制式外套》.pdf

《NAVY MIL-O-24926 A-1990 OVERCOAT WOMAN-S ENLISTED《女式制式外套》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-O-24926 A-1990 OVERCOAT WOMAN-S ENLISTED《女式制式外套》.pdf（61页珍藏版）》请在麦多课文档分享上搜索。

1、Thi SP pq MIL-0-24926A 3 April 1990 SUPERSEDING 14 March 1986 MIL-0-24926 MILITARY SPECIFICATION OVERCOAT, WOMANS, ENLISTED ification i approved for use by the Navy Cl thing and Textile Research Facility, Department of the Navy, and is available for use by all Departments and Agencies of the Departm

2、ent of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for the enlisted womans double breasted, finger tip length, overcoat (peacoat). 1.2 Classification. The overcoat shall be of one type only and in the following sizes and lengths (see 6.2): Sizes - 6, 8, 10, 12, 14, 16, 18

3、, 20, 38, 40, 42, and 44 Lengths - short, regular, and long 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified

4、, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be

5、of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by let

6、ter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL V-B-87 1 V-T-276 V-T-280 V-T-285 V-T-295 NN-P-71 ccc-c-441 DDD-L-LO DDD-T-

7、86 MILITARY MIL-C-297 MIL-B-371 MIL-C-15011 MIL-P-15064 MIL-C-15065 MIL-C-16290 MIL-C-16375 MIL-B-17143 MIL-C-17155 MIL-B-17757 MIL-C-21852 MIL-C-43525 MIL-T-43548 MIL-C-43718 STANDARDS FEDERAL FED-STD-191 FED-STD-751 o - - Button, Sewing Hole, and Button, Staple (Plastic) - Thread, Cotton - Thread,

8、 Gimp, Cotton, Buttonhole - Thread, Polyester - Thread, Nylon - Pallet, Material Handling, Wood, Stringer - Cloth, Corduroy, Cotton - Label; for Clothing, Equipage, and Tentage (General - Tape, Textile, Cotton, General Purpose (Unbleached, Construction, 2 Way and 4 Way (Partial) Use) Bleached, or Dy

9、ed) - Cloth, Interlining, Cotton Warp, and Spun - Braid, Textile (Tubular) - Pallet, Material Handling, Wood, Post Construction, - Pads, Shoulder and Sleeve-Head - Coat, Fronts - Cloth, Melton, Wool (Moth Proofed) - Cloth, Wigan, Cotton - Button, Insignia, (Anchor, Plastic, Black) - Cloth, Knitted,

10、Nylon Fleece - Boxes, Shipping, Fiberboard, (Modular Sizes) - Cloth, Taffeta, Nylon - Cloth, Satin, Acetate or Rayon Face and Rayon or - Thread, Polyester Core: Cotton-, Rayon-, or - Cloth, Twill, Polyester, Polyester and Cotton, Hair-Wool, or Rayon Filling 4 Way Entry Cotton Back Polyester-Covered

11、Polyester and Rayon for Pockets - Textile Test Methods - Stitches, Seams, and Stitchings 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-24926A MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 MIL-STD-147 -

12、Palletized Unit Loads Attributes - Marking for Shipment and Storage * MIL-STD-2073-1 - DOD Materials Procedures for Development and * MIL-STD-2073-2 Application of Packaging Requirements - Packaging Requirement Codes * (Unless otherwise indicated, copies of federal and military specifications, stand

13、ards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this doc

14、ument to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. U.S. POSTAL MANUAL (Copies may be obtained from the Superintendent of Document, U.S. Government Printing Office, Washington, DC 20402-0001). * 2.2 Non-Government publications. The follow

15、ing document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the

16、 DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W.,

17、Washington, DC 20036-1404). UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). 3 Provided by IHSNot for ResaleNo reproduction

18、or networking permitted without license from IHS-,-,-MIL-0-24926A THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades for Sewing Threads Department of Defense Standard Shade for Buttons (Application for copies of color cards should be addressed to the Color Association o

19、f the United States, 343 Lexington Ave., New York, NY 10016-0927). TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS Method No. 8 - 1988 - Colorfastness to Crocking: AATCC Crockmeter Method (Application or copies should be addressed to the AATCC National Headquarters, P.

20、O. Box 12215, Research Triangle Park, NC 27709-9989). (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) * 2.3 Order o

21、f precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes regulations unless a specific exemption has been obtained. precedence. Nothing in this document, however, supersedes applicable laws and - 3. REQUIREMENTS 3.1 G

22、uide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for fir

23、st article inspection and approval (see 4.3 and 6.2). o - 3.3 Materials. (See 6.4) * 3.3.1 Basic material. The basic material shall be 22 ounce wool melton, shade Blue 3346, conforming to type II, class 4 of MIL-C-16290, piece number 84241. 3.3.2 Linings. * 3.3.2.1 Lining, fleece. The knitted fleece

24、 material for lining the body shall conform to type III of MIL-C-17155. * 3.3.2.2 Lining, sleeves, yoke, and inside breast pocket facing. The material for lining the sleeves, yoke, and inside breast pocket facing shall be a napped-back satin, dyed to match Black 3202, conforming to type II of HIL-C-

25、43525, piece number 87036. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-2472bA 4 W 7777906 0414244 T W MIL-0-24926A 3.3.3 Nylon binding. The binding for the back edge of facings, bottom raw edge and vent shall be nylon taffeta cloth confor

26、ming to type IV of MIL-C-21852. The color shall be black. The nylon shall be cut on a 45 (+5) degree angle in strips of 7/8 to 1 inch width. The ends of the strips shall be joined together by stitch type 301, seam type SSa-1 with 10-12 stitches per inch. 3.3.4 Pocketing. 3.3.4.1 Inside pockets. The

27、material for the left inside pocket shall be polyester, poiyester/cotton, or polyester/rayon twill conforming to class 1 of MIL-C-43718. The shade shall be natural or black shade 423. * 3.3.4.2 Pocketing. The material for the front and cash pockets shall be a soft filled cotton flannel having a smoo

28、th suede finish on one side, in natural or gray shade and shall conform to the physical requirements shown in Table I when tested as specified in Table IV. TABLE I - Physical Requirements Characteristics Mi ni mum Weight (oz./sq. yd.) Yarns per inch: Warp Fi 11 ing WarD Breaking strength (pounds): 6

29、.0 44 40 60 Filiing 35 The use of sulphur dyes and dyes containing elementary sulfur or sulfur compounds capable of oxidation to sulfuric acid is prohibited. The dyed material shall show a minimum of “good“ colorfastness to wet-dry cleaning and shall show a AATCC Rating for crocking not lower than 3

30、 when tested as specified in Table IV (see 4.4.1). * 3.3.4.2.1 Pocketing. As an alternate, the material for the front pockets and cash pocket shall be cotton corduroy conforming to type I, class 1 of CCC-C-441. 3.3.5 Interlining. The material for interlining the collar shall be cotton warp, and spun

31、 hair-wool filling conforming to type I, class 2 of MIL-C-297. The color shall be black, grey, or natural. cotton wigan, natural color, conforming to type I of MIL-C-16375. 3.3.6 Wigan. The material for interlining the sleeve bottoms shall be * 3.3.7 Coat front. The coat fronts shall be manufactured

32、 in accordance with type XX of MIL-C-15065. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-24726A 194 m 7773706 0414245 L m MIL-0-24926A 3.3.8 Shoulder and sleeve-head pads. The shoulder pads shall conform to type I, class 1 and the sleeve-h

33、ead pads shall conform to type IV of NIL-P-15064. 3.3.9 Threads. * 3.3.9.1 Cotton or polyester-core thread. The thread for seaming and stitching the overcoat shall be either an all cotton or a polyester core thread conforming to V-T-276 or MIL-T-43548. A polyester-covered, polyester-core thread is n

34、ot allowed. The thread shall be dyed Black AA Cable No. 66043 of the Department of Defense Standard Shades for Sewing Threads, in the following types and sizes: Ticket No./ Ticket No, 2/ - Ply 1/ - Type 1/ - Seaming and stitching IC2 013 50 401 looper; 304 stitching IC2 013 70 Tacking armholes and a

35、ttaching sleeve-head pads IA1 or IA2 30/3 30 Buttonholes and bartacks IC2 A or B/3 30 Button sewing: Band IB3 12 or 16/4 30 Machine IA3 or IB3 20/4 30 1/ Applies to V-T-276. 2/ - Applies to MIL-T-43548. 3.3.9.2 Basting thread. Thread for basting and tacking may be bleached or unbleached and shall be

36、 of a good commercial grade cotton. A monofilament synthetic thread may be used for only those basting operations where the thread is require2 to be removed provided the garment is subsequently given a treatment by a cleaning agent in which the synthetic thread is soluble. When this thread is used,

37、any residue remaining on the garment after the dry cleaning process shall be brushed or removed. 3.3.9.3 Felling thread. 3.3.9.3.1 Polyester thread. For machine felling and blind felling, polyester thread conforming to type I, size A/3 or AA/2 of V-T-285 or a monofilament nylon thread of comparable

38、type and size shall be used. The color of the polyester thread shall be black. 3.3.9.3.2 Nylon thread. For hand felling, nylon thread conforming to type IV, size A/2 or C/2 of V-T-295 shall be used. The color shall be black. o- o:. I 6 Provided by IHSNot for ResaleNo reproduction or networking permi

39、tted without license from IHS-,-,-MIL-0-24926A * 3.3.9.3.3 Colorfastness. The dyed threads shall show colorfastness to wet-dry cleaning and light equal to or better than the standard sample when tested as specified in .V-T-276, V-T-285, V-T-295, or MIL-C-43548. As a limit of acceptability, or when n

40、o standard sample is available, the dyed thread shall show “good“ colorfastness to wet-dry cleaning and light when tested as specified in V-T-276, V-T-285, V-T-295, and MIL-C-43548. 3.3.9.4 Gimp. The gimp for reinforcing the buttonholes shall be cotton, buttonhole-gimp thread conforming to type I or

41、 II, size No. 8 of V-T-280. The gimp shall be dyed black. * 3.3.9.4.1 Colorfastness. The dyed thread shall show colorfastness to wet-dry cleaning equal to or better than the standard sample when tested as specified in V-T-280. As a limit of acceptability, or when no standard sample is available, the

42、 dyed thread shall show “good“ colorfastness to wet-dry cleaning when tested as specified in V-T-280. 3.3.10 Tapes. * 3.3.10.1 Woven tape. The tape shall be cotton, preshrunk, conforming to type I, class 1 or class 2 of DDD-T-86. The widths shall be as follows: 1/2 inch for staying lapels, fronts, b

43、ottom edges, and joining 5/8 inch for staying bridle at breakline of lapel 1/4 inch for staying back armhole, lower part of front front facing armhole, and fold line of left vent * 3.3.10.2 Cross-cut tape. The tape for staying the front shoulder, neck gorge, back neckline and upperpart of front armh

44、ole shall conform to class 1 of MIL-C-43718. The tape shall be cut across the width of the cloth in strips 1/2 (+1/16) inch wide and shall be dyed or undyed. The raw edges of the tape shallbe treated with a synthetic resin to prevent raveling (see 4.4.1). * 3.3.10.3 Tape, fusible. As an alternate, t

45、he tape for joining the fronts and facings shall be woven or non-woven with a thermoplastic polyamide resin applied ta the tape. The tape shall be natural color and shall be 5/8 inch in width (see 4.4.1). 3.3.11 Buttons. 3.3.11.1 Plastic anchor design buttons, The outside buttons shall conform to cl

46、ass 2 (50 ligne) of MIL-B-17143. * 3.3.11.2 Plastic button. The plastic buttons for anchoring the right front on the inside of the coat and anchoring the shoulder epaulets shall be shade Black BT, Cable No. 62001 in accordance with the Department of Defense Standard Shade for Buttons conforming to t

47、ype II, class D, style 20 and 21 of V-8-871. The hidden button for anchoring the right front on the inside of the coat shall be 45 ligne or as an alternate, the 50 ligne plastic anchor design button in paragraph 3.3.11.1 may be used. The epaulets shall have 30 ligne buttons. 7 Provided by IHSNot for

48、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-2492hA 4 W 7777906 0434247 5 W - -_- 3.3.13.2 Sfze abel, Each avermat shaPI. Rave a separate size label enfarinfng ta type VXF eaass 2 f DBIr-L-2Q wh8ch shal1 indicate the size and Sta an& 2 inches high, ma& of a sufta

49、hla plain white cardboardf. Ehe eorers a the ticket may be double perforated for ease in tacking* The size TZR - Example) shall #e printed OK stamped on the upper 3eft hand COEII ira black er Mue ik The ettering for the size shall be f/4 inch in hefgkt. Abbreviations far Eengths shall be allowed in accordance with 3.3,B3.Ee * 3.4 ksfgn. The dorable breasted avercoat is fleece lined (fleece si6e of Hnhg away nont the wea