NAVY MIL-M-3184 C-1986 MACHINERY DECK AND VEHICLE MOUNTED WITH ASSOCIATED EQUIPMENT AND PROVISIONED (REPAIR PARTS) ITEMS PACKAGING OF《机械装置 相关设备和准备(修理部件)细目的甲板和运载体装置》.pdf

《NAVY MIL-M-3184 C-1986 MACHINERY DECK AND VEHICLE MOUNTED WITH ASSOCIATED EQUIPMENT AND PROVISIONED (REPAIR PARTS) ITEMS PACKAGING OF《机械装置 相关设备和准备(修理部件)细目的甲板和运载体装置》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-M-3184 C-1986 MACHINERY DECK AND VEHICLE MOUNTED WITH ASSOCIATED EQUIPMENT AND PROVISIONED (REPAIR PARTS) ITEMS PACKAGING OF《机械装置 相关设备和准备(修理部件)细目的甲板和运载体装置》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-M-3184C 3 April 1986 SUPERSEDING MIL-M-3184B 3 November 1969 (See 6.7) MILITARY SPECIFICATION MACHINERY: DECK AND VEHICLE MOUNTED WITH ASSOCIATED EQUIPMENT AND PROVISIONED (REPAIR PARTS) ITEMS; PACKAGING OF This specification is approved for use by all Departments and Agencies of the Department

2、of Defense. 1. SCOPE 1.1 Scope. This specification covers the packaging (cleaning, drying, preservation, packing, and marking) requirements for machinery, such as cap- stans, davits, sliding padeyes, elevators, conveyors, cranes, hoists, stream transfer heads, ram tensioners, sliding blocks, sliding

3、 block drives, winches, windlasses, accessories, associated equipment, and provisioned (repair parts) items. 2. APPLICABLE DOCUMENTS 2.1 Government document s. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified her

4、ein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL P-D-680 - Dry Cleaning Solvent. TT-P-664 - Primer, C

5、oating, Synthetic, Rust-Inhibiting, UU-P-268 - Paper, Kraft, Wrapping. PPP-B-566 - Boxes, Folding Paperboard. PPP-B-576 - Boxes, Wood, Cleated, Veneer, Paper Overlaid. PPP-B-585 - Boxes, Wood, Wirebound. Lacquer-Resisting. Beneficial comments (recommendations, additions, deletions) and any pertinent

6、 data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this documen

7、t or by letter. AMSC N/A AREA PACK DISTRIBUTION STATEMENT A Approved for public release; distribution unlimited Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HI L-H- 3 184 C FEDERAL (Continued) PPP-B-591 - PPP-B-601 - PPP-B-621 - PPP-B-636 - PPP-B-

8、640 - PPP-B-665 - PPP-B-676 - PPP-B-1055 - PPP-c-795 - PPP-C-843 - PPP-C-850 - PPP-c-1120 - PPP-c-1752 - PPP-c-1797 - PPP-F-320 - PPP-H-1581 - PPP-P-40 - PPP-P-291 - PPP-T-60 - MILITARY MIL-V-3 - MIL-C-104 - MIL-P-116 - MIL-B-121 - MIL-P-149 - MIL-R-196 - MIL-B-197 - MIL-B-208 - MIL-B-233 - MIL-P-77

9、5 - MIL-L-2105 - MIL-B-3106 - MIL-H-3280 - Boxes, Shipping, Fiberboard, Wood-Cleated. Boxes, Wood, Cleated-Plywood. Boxes, Wood, Nailed and Lock-Corner. Boxes, Shipping, Fiberboard. Boxes, Fiberboard, Corrugated, Triple-Wall. Boxes: Paperboard, Metal Edged and Components. Boxes, Setup. Barrier Mater

10、ial, Waterproofed, Flexible. Cushioning Material, Flexible, Cellular, Plastic Cushioning Material, Cellulosic. Cushioning Material, Polystyrene, Expanded, Resilient (For Packaging Uses). Cushioning Material, Uncompressed Bound Fiber for Packaging. Cushioning Material, Packaging, Unicellular Polyethy

11、lene Foam, Flexible. Cushioning Material, Resilient, Low Density, Unicellular, Polypropylene Foam. Fiberboard; Corrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes. Hardware (Fasteners and Related Items), Packaging of. Packaging, Packing, and Marking of Hand Tools. Paperboard, Wrappin

12、g and Cushioning. Tape : Packaging, Waterproof. Film For Packaging Applications. Valves, Fittings, and Flanges (Except for Systems Crates, Wood; Lumber and Plywood Sheathed, Nailed Preservation, Methods of. Barrier Material, Greaseproofed, Waterproofed, Plastic Coating Compound, Strippable (Hot Repa

13、ir Parts, Accessories, and Kits, Mechanical; Bearings, Anti-Friction, Associated Parts and Sub- Battery, Storage, Lead Acid, Automotive and Navy, Indicated Herein); Packaging of. and Bolted. Flexible. Dipping). Packaging of. Assemblies, Preparation for Delivery of. Portable (Except Aircraft), Packag

14、ing and Packing of. Boxes, Repair Parts , Storage. Packaging of Hose, Hose Assemblies ; Rubber, Plastic, Fabric, or Metal (Including Tubing); And Fittings, Nozzles, and Strainers. Lubricating Oil, Gear, Multipurpose. Board, Composition, Water-Resistant, Solid (For Hoists, Chain, Manually Operated, P

15、ackaging of. Filler or Cushioning Pads). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-3184C MILITARY (Continued) MIL-C-3580 - Crane and Crane-Shovels, Truck, Crawler, and Wheel Mounted, Full-Revolving, and Their Attachments, Packaging of.

16、MIL-C-3774 - Crates, Wood; Open 12,000- and 16,000-Pound Capacity. MIL-B-3865 - Blocks, Rope, Tackle: Packaging of. MIL-P-4861 - Packing, Preformed, Rubber, Packing; Packaging of. MIL-R-5001 - Rubber Cellular Sheet, Molded and Hand Built Shapes; Latex Foam. MIL-C-5501 - Caps and Plugs, Protective, D

17、ust and Moisture Seal, General Specification for. MIL-H-6083 - Hydraulic Fluid, Petroleum Base, For Preservation and Operation. MIL-R-6130 - Rubber, Cellular, Chemically Blown. MIL-1-8574 - Inhibitors, Corrosion, Volatile, Utilization of. MIL-C-9897 - Crates, Slotted Angle, Steel or Aluminum, for Li

18、ghtweight Airframe Components and Bulky Item (For Maximum Loads of 3000 Pounds). Preparation for Shipment and Storage of. MIL-E-10062 - Engine: MIL-L-10547 - Liners, Case, and Sheet, Overwrap; Water-Vaporproof MIL-S-12134 - Synchros, Resolvers, and Servo Motors; Packaging of. MIL-V-13811 - Varnish,

19、Waterproofing, Electrical, Ignition. MIL-E-16298 - Electric Machines Having Rotating Parts and MIL-P-16789 - Packaging of Pumps, Including Prime Movers and MIL-P-17286 - Propulsion and Auxiliary Steam Turbines and Gears or Waterproof, Flexible. Associated Repair Parts: Packaging of. Associated Repai

20、r Parts. (Including Repair Parts, Tools, Accessories and Instruments): Packaging of. MIL-C-17435 - Cushioning Material, Fibrous Glass. MIL-E-17555 - Electronic and Electrical Equipment, Accessories, MIL-P-17869 - Pumps and Motors, Power, Oil Hydraulic (Naval MIL-H-19457 - Hydraulic Fluid, Fire-Resis

21、tant, Non-Neurotoxic. MIL-R-20092 - Rubber Sheets and Molded Shapes, Cellular, Syn- thetic, Open Cell (Foamed Latex). MIL-L-21260 - Lubricating Oil, Internal Combustion Engine, Preservative And Break-In. MIL-B-22019 - Barrier Materials, Transparent, Flexible, Sealable, Volatile Corrosion Inhibitor T

22、reated. MIL-B-22020 - Bags, Transparent, Flexible, Sealable, Volatile Corrosion Inhibitor Treated. MIL-B-22191 - Barrier Materials, Transparent, Flexible, Heat Sealable. MIL-E-23457 - Engines, Diesel, Marine Propulsion and Auxiliary, Medium Speed. MIL-1-24092 - Insulating Varnish, Electrical, Impreg

23、nating, Solvent Containing. MIL-A-25175 - Air Transport, Nontactical, Packing for. MIL-P-26514 - Polyurethane Foam, Rigid or Flexible, for Packaging. and Provisioned Items (Repair Parts): Packaging of. Shipboard Use). Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

24、se from IHS-,-,-flIL-M-3184C PA D 797990b 0277707 5 D MIL-M-3184C MILITARY (Continued) MIL-C-26861 - Cushioning Material, Resilient Type, General. MIL-C-52950 - Crates, Wood, Open and Covered. MIL-C-55442 - Cable Assemblies and Cord Assemblies, Packaging of. MIL-B-55521 - Batteries, Nonrechargeable,

25、 Packaging of. STANDARDS FEDERAL FED-STD-313 - Material Safety Data Sheets Preparation and the Submission of. MILITARY MIL-STD-129 MIL-STD-147 - Palletized Unit Loads. MIL-STD-163 MIL-STD-740 - Airborne and Structureborne Noise Measurements MIL-STD-758 MIL-STD-1186 - Cushioning, Anchoring, Bracing,

26、Blocking, and MIL-STD-1367 - Packaging, Handling, Storage, and Transport- - Marking for Shipment and Storage. - Steel Mill Products Preparation for Shipment and Storage. and Acceptance Criteria of Shipboard Equipment. Part s. Waterproofing; with Appropriate Test Methods. ability Program Requirements

27、 (For Systems and Equipments). - Packaging Procedures for Submarine Repair 2.1.2 Other Government documents. The following other Government docu- ments form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the

28、 solicitation. DEPARTMENT OF LABOR Code of Federal Regulations, Title 29 Part 1910, Section 145 and 1001 Asbestos - Occupational Safety and Health Standards. (Application for copies should be addressed to the Superintendent of Docu- ments, U.S. Government Printing Office, Washington, DC 20402.) (Cop

29、ies of specifications, standards and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this

30、specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue

31、of the non- government documents which is current on the date of the solicitation. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-fl-3L84C PA 9 999970b 0277708 7 MIL-M- 3 1 H C I AMERICAN NATIONAL STANDARDS INSTiTCTL (ANSI) MH15.1 - Glossary

32、 of Packaging Terms (Application for copies should be addressed to the American National Standards Institute, 1430 Broadway, New York, NY 10018.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) Environments. (DoD adopted) D 996 - Standard Terminology of Packaging and Distribution D 3951 - Standard

33、 Practice for Commercial Packaging. (Application for copies should be addressed to the American Society for Testing and hterials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute

34、 the documents. These documents also may be available in or through libraries or other informational sen ices. ) 3. REQUIREMENTS 3.1 -finitions or explanation of packaging terms. Definitions or expla- nation of packaging terms, applicable to this specification, shall be as stated in the applicable r

35、eferenced specification and 6.4 herein. or explanation of packaging terms not specified therein, ANSI MH15.1 and ASTM D 996 shall apply. For definitions 3.2 - Order of precedence. When an equipment or item is acquisitioned in conformance to a commodity specification having detailed packaging or prep

36、ara- tion for delivery requirements which differ from this specification, the packaging or preparation for delivery specified in the commodity specification shall apply. 3.3 First article. #en specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4

37、.4.1 and 6.3). 3.3.1 Dummy or simulated load. When specified (see 6.2.1), a dummy or simulated load may be used for rough handling tests (see 4.4.2). or simulated load is substituted for the actual equipment or item in performing the rough handling tests, instrumentation of the pack is required for

38、assurance that the acceleration of the packed item during the tests is less than the fragility rating of the item. The details of the instrumentation including location shall be included with the test results (see 4.4.3). Notification of tests shall be in accordance with the data ordering document (

39、see 6.2.2). When a dummy 3.4 Materials. The materials shall be as specified herein. 3.4.1 Recovered materials. - Unless otherwise specified herein, all equip- ment, material, and articles incorporated in the products covered by this specification shall be new and may be fabricated using materials pr

40、oduced from recovered materials to the maximum extent practicable without jeopardizing the intended use. The term “recovered materials“ means materials which have been 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-fl-3L84C PA 999990b 0279709

41、9 MIL-M-3184C collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. None of the above shall be interpreted to mean that the use of used or rebuilt products is allowed under this specification unless otherwise specifically spe

42、cified. 3.4.2 New materials. The use of newly developed packaging materials or procedures are encouraged and recommended and will be permitted under the conditions specified herein, provided they are equal to or better than the specified materials or procedures. 3.4.2.1 Certification of new material

43、s. If the contractor desires to use materials or procedures other than those specified herein, he shall furnish to the contracting activity documented evidence in the form of a certificate of compliance (see 6.2.2), certified by a testing laboratory satisfactory to the contracting activity that the

44、material or procedure is equal to or exceeds the requirements specified herein. If, after a review of the material or procedure and the related documented evidence, or the witnessing of the stipulated tests, it is the opinion of the contracting activity that the material or procedure meets or exceed

45、s the requirements specified herein, authorization for use will be granted. 3.4.3 Asbestos. (See 6.5.) 3.4.3.1 Packaging materials. Asbestos or material and items containing asbestos shall not be used in the packaging of material or items covered by this specification (see 6.5). 3.4.3.2 Packaged ite

46、ms. Asbestos, and separately packaged components containing asbestos that is predominately distributed throughout the item, shall be packaged in sealed, dust and siftproof packages. Flexible packages shall be heat sealed. Packages shall be marked as specified (see 3.12.2.4). 3.4.3.3 Dusting material

47、. Dusting material such as talc and talcum shall be asbestos free. A certificate of compliance (see 6.2.2), shall be furnished stating that the dusting material is asbestos-free. 3.4.4 Cushioning and wrapping materials (see 3.8.1.1.27). The use of excelsior, newspaper, shredded paper (all types) and

48、 similar hydroscopic or nonneutral materials and all types of loosefill materials for applications such as cushioning, filler, stuffing, and dunnage is prohibited. Materials selected for cushioning and wrapping shall have properties (characteristics) resistant to fire. 3.5 Technical data. Complete d

49、escriptive packaging details on drawings, test results, and packaging and transportation data requirements are not required when such were previously submitted and accepted by the contracting activity. 3.5.1 Data and drawings. When specified (see 6.2.1), the contractor shall prepare complete descriptive packaging details on drawings of the sample pack in accordance with the data ordering document included in the contract or order (see 6.2.2). 6 Provided by IHSNot for ResaleNo reproduction