NAVY MIL-M-29437-1988 MODULE ASSEMBLY UNIVERSAL STORAGE《普通储存模块组装》.pdf

《NAVY MIL-M-29437-1988 MODULE ASSEMBLY UNIVERSAL STORAGE《普通储存模块组装》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-M-29437-1988 MODULE ASSEMBLY UNIVERSAL STORAGE《普通储存模块组装》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、S-06-03 1 4 MIL-M-29437 (MC) 20 January 19 88 MILITARY SPECIFICATION MODULE ASSEMBLY, UNIVERSAL STORAGE This specification is approved for use within U.S. Marine Corps, Department of the Navy, sand is available for use- by all depart- ments and agencies of the Department of Defense. 1. SCOPE 1.1 Sco

2、pe. This specification establishes the requirements for manufacture and acceptance of the Module Assembly, Universal Storage. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications .and standards. The following speci- fications and standards form a part of this specification to the e

3、xtent specified herein. Unless otherwise specified, the issues of these documents shall be-those listed in the issue of the Department of. Defense Index of Specifications and Stndards (DOPISS) ,. and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL V-T-295 - Thread Nylon. QQ-A-2

4、00/8 - Aluminum Alloy 6061, Bar, Rod, Shapes, Tube and Wire, Extruded. QQ-A-225/8 - . Aluminum Alloy 6061, Bar, Rod, Wire and Special Shapes, Rolled, Drawn or Cold Finish. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving.this documen

5、t should be addressed to: Commandant of the Marine Corps, Headquarters Marine Corps (Code LMA-l), Washington, DC 20380 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. . FSC 7125 AMSC N/A DISTRIBUTION -STATEM

6、ENT A. Approved for public release; distri- THIS DOCUMENT CONTAINS q PAGES. bution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-A-250/8 QQ- S- 78 1 PPP-B-6 O 1 PPP-B-62 1 MILITARY MIL-P-116 MIL-11 7 MIL-T-70 4 MIL-W-4088 MIL-S-505

7、9 MIL-(2-5541 MIL-E-6060 MIL-S-772 O MIL-G-12803 M IL-P-19 8 3 4 MIL-C-22750 * . . MIL-W-45205 MIL-P-53022 MIL-M-29437 (MC) e I Aluminum Alloy 5052, Plate and Sheet. I Strapping, Steel and Seals . - Boxes, Wood, Cleated Plywood . . Box, Wood, Nailed and Lock-corner. Preservation, Methods of. Bag, Sl

8、eeve and Tubing - Interior Treatment and Painting of Material. Webbing, Textile, Woven Nylon. Steel, Corrosion-Resistant (18-8) Plate, Sheet and Strip (ASG). Chemical Conversion Coatings on Aluminum Alloys Envelope, Packaging, Water Vapor Proof, Flexible. Steel, Corrosion-Resistant -(18-8) Bars, Wir

9、e and Forging Stock (Aircraft Quality) . Gasket Material, Non-metalic. Plate, Identification, Metal Foil, Adhesive Backed. Coating, Epoxy Polyamide . Welding, Gas Metal-Arc and Gas * Tungsten-Arc, Aluminum .Alloys , Readily Weldable for Structures, Excluding Amor . Primer, Epoxy Coating, Corrosion I

10、nhibiting, Lead and Chromate Free. Packaging. STANDARDS FEDERAL FED-STD-595 - Federal Standard Colors. MILITARY MIL-STD-10 5 - Sanipling Procedures and Tables for MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-130 - Identification Marking of U.S. MIL-CTD-2073-1A - DoD Material Procedures fo

11、r Develop- Inspection by Attributes . Military Property. ment and Application of Packaging . Requirements . 2.1.2 Other Government documents, drawings, and publications. The fallowing other Government documents, drawings, and publica- tions form a part of this specification to the extent specified h

12、erein. Unless otherwise specified, the issues shall be those in a effect on the date of the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-M-29437 (MC) DRAWINGS U.S. Marine Corps Logistics Base, Albany, GA . 82A5048A1300 - Modu

13、le Assembly, Universal Storage 82A5048A1131 - Shelf, Tie Down 82A5050A0100 - Rail Assembly and Installation, Mounting, Floor 82A5050A0110 - Peg Assembly, Modular Alignment 82A5050A0132 - Bar, Lock 82A5050A0138 - Shaft, Latch 82A5050A0140 - Head, Latch 82A5050A0142 - Handle, Latch 82A50 50A0144 - Lat

14、ch 82A5050A0150 - Rail Assembly and Installation, Mounting, . 82A5050A0160 - Post Assembly, Mounting Wall (Copies of specifications, standards, handbooks, drawings, publications, and other government documents required by suppliers in connection with specified procurement functions should be obtaine

15、d from the contracting agency or as directed by the con- tracting officer). 2.2 Non-Government documents. The following document (s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those- listed

16、in the. issue of the DODISS 0 specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue o-f the nongovernment documents which is current on the date of the solicitation. AMERICAN NATIONAL STANDARDS INSTITUTE ANSI/AWS A2.4-79 - Weld

17、ing and Nondestructive ANSI/AWS A3.0-85 - Welding Terms and Definitions, Testing, Symbols. (Application for copies should be addressed to the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018.) (Nongovernment standards and other publications are normally available from t

18、he organizations which prepare or which distribute the documents. These documents also may be available in or through- libraries or other informational services.) AMERICAN SOCIETY FOR TESTING AND MATERIALS AS,TM A108-81 - Steel Bars, Carbon, Cold Finished, Standard Quality (Applicationfor copies sho

19、uld be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- ._._. . . MIL-M-9Y37 71 U 999990b OiYOYBL B b MIL-M-29437 (MC) 2.3 Order or precedence In

20、the event of a conflict between the text o this specification and the references cited herein (except or associted detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall super- sede applicable

21、laws and regulations unless a specific exemption has been obtained. 3, REQUIREMENTS 3.1 First article. When specified in the contract or pur- chase order,. a sample shall be subjected to first article inspec- tion (see 4.3 and 6.4) . 3.2 Materials. The materials and components shall be certi- fied t

22、o conform to the applicable specification and standards as Listed on drawing package 82A5048A1300 or required herein. The materials used may include reclaimed materials provided such materials will not jeopardize its intended use and performance. The reclaimed materials shall have been reprocessed,

23、remanufactured., or recycled in a manner whdch will restore them to the same chemical composition and physical properties as the materials originally selected for use as specified herein. of the design specified on- drawing package 82A5048A1300 (see 2.1.2). 0 3.3 Design. Module Assembly, Universal S

24、torage, shall be 3 . 4 Construction . Module Assembly, Universal Storage, shall be of the construction and physical dimensions specified on drawing - - package 82A50 48A1300 (see 2 . 1.2) . cated from Sheet, Aluminum Alloy 5052-H32, QQ-A-250/8; Angle, Aluminum Alloy 6061-T6, QQ-A-200/8; Rod, Aluminu

25、m Alloy 6061-T6, QQ-A-225/8; Bar, Aluminum Alloy 6061-T-6510, aQ=A-200/8; and shall be square in all directions within .O10 inch per foot (see 4.4.2). Al1 welds shall be in accordance with ANSI/AWS A3.01185, A2.4-79 and MIL-W-45205, Class B (see 4.4.4). The frame assembly shall conlorm to the specif

26、ications to such a degree of accuracy it will align to the peg and pin assemblies and lock using the swing latch as illustrated in the footprint drawing Figure 1 (see 4.4.3). 3.4.1 Frame assembly, The frame assembly shall be fabri- 3.4.2 Drawer assembly, 14 inch. The drawer assembly and drawer suppo

27、rt shall be fabricated from Sheet, Aluminum Alloy, 5052-H32 ,-h-A-25 0/8 . All welds shall be in accordance with ANSI / AWC A3.0-85, A2.4-79 and MIL-W-45205 Class B (see 4.4.4). Each latch grip shall be installed on the front of the drawer usinq two screws . The slide, drawer, extension (3 . 5) Stru

28、ctural Members shall be fabricated from Aluminum Alloy with a minimum yield strength of 35,000 psi, ultimate tensile strength of 200,000 psi. The slide, drawer, extension (3.5) Component Parts shall be of 300 Series Stainless Steel per MIL-S-5059 or MIL-S-7720, Carbon Steel per ASTM A108-81 and/ . s

29、lide ball raceways shall have a minimum 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.a MIL-M-27437 71 m 977770b 0240q2 T m MTL-M-29437 (MC) or Aluminum Alloy. The slide, drawer, extension (3.5) load rating (per pair) at 22 inch extension shall

30、be 200 lbs. Each drawer support shall be securely bolted to the frame assembly in three places. Each slide, drawer, extension (3.5) shall be screwed to the drawer support in six places. The drawer assembly shall-be screwed to the slide, drawer, extensions (3.5) in 12 places. Installed the drawer ass

31、embly shall operate smoothly and freely with nobinding and close against the frame (see 4.4.5). Each drawer assembly, .14 inch shall be capable of being interchanged for another (see 4.4.6). 3.4.3 Strap assembly, tie down. The strap assembly, tie down shall be fabricated from Strap, Webbing, MIL-W-4

32、088, Type II, Class I, 2500 lbs minimum strength, color Gray; Strap, Webbing MIL-W-4088, Type XXVII, Class I, 6500 lbs minimum strength, color Gray; sewn with Thread per Fed Spec V-T-295, Type II, Class A, Type B, color Black per FED-STD-595. Attaching hardware shall consist of Rotating End Fitting;

33、 Plate, Threading; Hook, Flat; and Fastener, Flat Hook. Attaching hardware shall be Cold Rolled Steel, 300 lbs minimum strength with HD Zinc Plate Bronze Chromate Finish. The strap assembly shall be fabricated to have a minimum strength of 300 lbs (see 4.4.7). 3.4.4 Shelf assembly, stationary. The s

34、helf assembly, tie down, shall be in accordance with drawing 82A5048A1131. The shelf shall be securely screwed .tothe frame assembly in 16.places (see 4.4.8). 3.4.5 Bracket mounting. The bracket mounting, shall be fabricated of Angle, Aluminum Alloy, 6061-T6, QQ-A-200/8 and shall be securely bolted

35、to the frame in four places to such a degree of accuracy ensuring it will align to the foot.print as described in Figure 1 (see 4.4.9). thick aluminum alloy foil, photographically sensitized, adhesive back in accordance with MIL-P-19834, Type I. Requirements and methods of marking the decal shall be

36、 in accordance with MIL-STD- 130. Unless otherwise specified all characters shall be .O93 inch high on finished decal, color shall be in accordance with MIL-P- 19834, Style III (see 4.4.10). 3.4.6 Decal. The decal shall be fabricated from .O03 inch 3.5 Finish. 35.1 Cleaning. Prior to painting metal

37、surfaces shall be cleaned and treated per MIL-T-704, Type G, and MIL-C-5541, Class 3. 3.5.2 Priming. After metal surfaces have been cleaned ,as required they shall be primed per MIL-P-53022, with a minimum dry - film thickness of .O01 inch in one coat. 3.5.3 Painting. Final finish painting shall hav

38、e a minimum dry coat film thickness of .O018 inch in two coats per MIL-C-22750, Type II, Color No. 24533 per FED-STD-595 (see 4.4.13). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-29437 (MC) 3.6 Interch-anqeabilit . All parts having the sa

39、me part number shall be functional and dimensionally interchangeable. Interchangeable parts are defined as two or mre like parts possessing such functional and physical characteristics as to be equivalent in performance and durability, and capable of being exchanged one for the other without alterat

40、ion of the parts them- selves or adjoining parts and without selection for fit or perform- ance . 3.7 Workmanship. The Module Assembly, Universal Storage shall meet all design, fabrication, assembly and finish require- ments of this specification. Particular attention shall be given to: sians; thoro

41、ughness of welding; painting; alignment; tightness of screwst bolts, and rivets. Failure to ensure these measures have been taken will be considered adequate basis for rejection of items being of inferior quality for the purpose intended. removal of burrs and sharp edges; accuracy of dimen- 4. QUALI

42、TY ASSURANCEPROVICIONS 4 . 1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase.ofder, the contrac

43、tor may use his own or any other -facilities suitable for the.performance of the inspection require- ments specified hereinc unless disapproved by the Goveqnment. TheGovernment reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed neces

44、sary to assure supplies and services conform to prescribed requirements. I 4.1.1. Responsibility for compliance. All items must meet all requirements of section 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program

45、. The absence of any inspec- tion requirements in the specification shall not relieve the con- tractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. does not authorize submission of known defec

46、tive material, either indicated or actual, nor does it commit the Government to acceptance of defective- material. Sampling in quality conformance 4.1.2 Test equipment and inspection facilities. When specified (see 6.2) the contractor -shall insure that test and inspection facilities of sufficient a

47、ccuracy, quality and quantity - are established and maintained to permit performance of required inspectioris. 4.2 Classification of inspections. The inspections specified herein are classified as follows: 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

48、S-,-,-% MIL-U-27437 71 777770b 0240484 3 c MIL-M-29437 (MC) a. First article inspection. First article inspection 9 consists of examinations and tests performed on samples which are representative of the production item after award of a contract to determine that the production item conforms to the

49、requirements of this specification (see 4.3). b. Quality conformance inspection. Quality conformance inmection consists of examinations and tests performed on indivi- dual products to determine conformance of the products with the requirements set forth in this specification (see 4.4). c. Visual inspection. Visual inspection consists of examinations to determine conformance with .the requirements set forth in this specification (see 4