NAVY MIL-L-82893 A-1994 LEAD FOIL《铅箔》.pdf

《NAVY MIL-L-82893 A-1994 LEAD FOIL《铅箔》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-L-82893 A-1994 LEAD FOIL《铅箔》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-L-62693A 9999906 1985970 961 W MIL-L-82893A(OS) 5 Augst 1994 SUPERSEDING 24 January 1994 MIL-L-82893(OS) MILITARY SPECIFICATION LEAD FOIL This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of t

2、he Department of Defense. 1. SCOPE 1.1 Scope. This specification establishes the requirements for lead foil used for chemical purposes in propelling charges for Navy guns (see 6. i). 2, APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Standards. The following standards form a part of this docume

3、nt to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). * STANDARDS MILITARY MIL-STD-129 Marking

4、 for Shipment and Storage MIL-STD-1169 Packaging, Packing, and Marking for Shipment of Inert Ammunition Components DOD-STD-2 101 Classification of Characteristics Beneficial comments (recommendations, additions, deletions) and my pertinent data which may be of use in improving this document should b

5、e addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Standardization Branch (Code 8420), Indian Head, MD 20640-5035 by using the Standardization Proposal (DD Form 1426) appearing at the end of this document, or by sending a letter. . AMSC NIA FSC 9535 DISTRIBUTION STATEMENT

6、 A: Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-fiIL-L-82893A 9qOh 1985971 8T8 m (Unless otherwise indicated, copies of federal and military specifications and standards are available from t

7、he Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094.) * 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopt

8、ed are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) E 37 Chemical Analysis of Pig

9、Lead E 117 Spectrographic Analysis of Pig Lead by the Point-to-Plane Technique (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1 187 .) 2.3 Order of precedence. In the event of a conflict between the text of this

10、 document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials (M101). The raw material shall be such as to produce lead

11、foil meeting the requirements of this specification. The lead foil shall be either primary or secondary lead produced from ore or other materials by a conventional process of reduction and refining or other processes which equally preclude the presence of unusual deleterious elements. 3.2 Chemical c

12、omposition (M102). The lead foil shall conform to the chemical composition requirements shown in Table I (see 4.3.1). 3.3 Dimensions (M103). The lead foil shall be 0.050 k 0.008 mm in thickness. Width shall be 51 cm (20.0 inches) or as specified in the contract or purchase order (see 6.2). Rolls (se

13、e 3.4) shall not vary from the ordered width by more than f 6.4 mm (see 4.3.2). 3.4 Form. Unless otherwise specified in the contract or purchase order (see 6.2), the lead foil shall be supplied in rolls. The weight of each roll shall not exceed 36 kg (see 4.3.2). 3.5 Workmanship (M104). The lead foi

14、l shall be free from dirt, grit, and any other foreign material (see 4.3.2). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-82893A m 9999906 1985972 73V m Lead Tin MIL-L-82893A(OS) TABLE 1. Chemical comuosition. 99.70 o. 1 II Element I Maxim

15、um percent 11 Antimony Arsenic Iron Bismuth Zinc Copper Silver 0.07 0.002 0.002 0.025 0.001 0.04 - 0.08 0.02 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order (see 6.2), the contractor is responsible for the performance of

16、 all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the G

17、overnment. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of

18、 sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products

19、or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material,

20、either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Classification of characteristics. The requirements verified by the tests and examinations herein are classified as critical, major, or minor in accordance with DOD-STD-2101. Requirements for critical c

21、haracteristics are identified by the symbol (C) and major characteristics by the symbol (M). The number following the classification symbol indicates the serial number of the characteristic. Requirements not annotated with a classification code are classified as minor. 3 Provided by IHSNot for Resal

22、eNo reproduction or networking permitted without license from IHS-,-,-MIL-L-82873A 999990b 1985973 670 = 4.2 Quality conformance inspection. 4.2.1 Inspection lot. For inspection purposes, a lot shall consist of all lead foil produced by one manufacturer and offered for inspection at one time but sha

23、ll not exceed 2270 kg. When specified in the contract or purchase order, a lot for chemical analysis shall also be limited to the lead foil produced by one manufacturing or smelting heat. For this case, a lot that cannot be identified by heat shall be cause for rejection. 4.2.2 Sampling for chemical

24、 analysis. Two samples for chemical analysis shall be selected from each lot. Each sample shall consist of not less than 600 grams (g) and shall be free from oil, iron, dirt, grit, or other foreign matter. The samples shall be separately packed, labeled, and forwarded to a laboratory for analysis. W

25、hen a spectrographic analysis is to be made, the quantity and form of the samples shall be as required by the laboratory at which the analysis is to be performed. 4.2.3 Rejections. If a test specimen fails to meet any of the requirements of this specification, it shall be cause for rejection of the

26、lot represented by the specimen. If any lead foil fails to meet the visual or dimensional examination (see 4.3.2), the lot shall be rejected. * 4.2.4 Retests. Retests shall be permitted when approved by the responsible Government Engineering Activity. 4.3 Methods of inspection. * 4.3.1 Chemical anal

27、ysis. A chemical analysis shall be made on each sample selected in accordance with 4.2.2 by chemical or spectrographic methods of ASTM E 37 or ASTM E 117 to determine compliance with the requirements of 3.2. In case of a dispute,chemical analysis by chemical methods shall be the basis for acceptance

28、 of chemical composition and spectrographic analysis shall be the basis for acceptance of impurity elements of less than 0.01 percent. The contractor shall furnish an analysis (see 6.3) of each melt showing the percentage of each of the elements specified in 3.2. In those instances where the amount

29、of an element allowed by this specification is greater than the concentration range given in either ASTM E 117 (antimony, tin, and iron) or ASTM E 37 (tin and antimony) standard accepted laboratory practices that are suitable for determining the amount of the element shall be employed. 4.3.2 Visual

30、and dimensional inspection. All material in the lot shall be visually and dimensionally examined to verify compliance with the requirements of this specification for form (3.4) and workmanship (3.5). A sufficient number of measurements shall be taken over each roll to ensure that the dimensional tol

31、erances of 3.3 are met. 4.3.4 Inspection of packaging. The packaging, packing, and marking shall be visually examined for conformance to section 5. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-82893A 9999906 1985974 507 MIL-L-82893A(OS) 5.

32、 PACKAGING 5.1 Packaging. The lead foil shall be packaged in rolls (see 3.4 and 6.2). 5.2 Packing. Packing shall be level A, B, or C, as specified in the contract of purchase order, * and shall be in compliance with MIL-STD-1169. 5.3 Marking. In addition to any special marking required by the contra

33、ct or purchase order (see 6.2), all markings for shipment shall be in accordance with MIL-STD-129. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful but is not mandatory). 6.1 Intended use. The lead foil specified herein is intended for use as a gun b

34、arrel decoppering agent. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. b. C. d. e. f. g. h. i. * Title, number, and date of this specification. Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced

35、 (see 2.1.1). Dimensions if other than as specified (see 3.3). Form, if other than rolls (see 3.4). When lot is to be limited to one heat (see 4.2.1). Analysis report if other than as specified (see 4.3. i). Applicable level of packing (see 5.2). Special marking, if required (see 5.3). That no ozone

36、 depleting substances (ODS) are used in the manufacture of this item. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-82893A = 9999906 1985775 443 6.3 Consideration of data requirements. The following data requirement should be considered whe

37、n this specification is applied on a contract. The applicable Data Item Description (DID) should be reviewed in conjunction with the specific acquisition to ensure that only essential data are requested/provided and that the DID is tailored to reflect the requirements of the specific acquisition. To

38、 ensure correct contractual application of the data requirements, a Contract Data Requirements List D Form 1423) must be prepared to obtain the data, except where DOD FAR Supplement 27.475-1 exempts the requirement for a DD Form 1423. Reference DU aeraDh DID Number DID Title 4.3.1 UDI-T-23 19 1B Cer

39、tification data for material The above DID was cleared as of the date of this specification. The current issue of DOD 5010.12- L, Acquisition Management Systems and Data Requirements Control List (AMSDL), must be researched to ensure that only current, cleared DIDS are cited on the DD Form 1423. * 6

40、.4 Changes from previous issue. The margins of this specification are marked with an asterisk to indicate where changes (additions, modifications, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies

41、 in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. 6.5 Subject term (key word) listing. Chemical analysis Decoppering agent Spectrographic testing Preparing Activity: (Project 9535-N055) Navy - OS 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-