NAVY MIL-J-24949-1989 JUMPER WOMAN-S WHITE《女式白色工作服》.pdf

《NAVY MIL-J-24949-1989 JUMPER WOMAN-S WHITE《女式白色工作服》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-J-24949-1989 JUMPER WOMAN-S WHITE《女式白色工作服》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-J-24747 84 9 7797906 0385251 3 - - -_ INCH-POUND MIL-J-24949(NU) 17 July 1989 MILITARY SPECIFICATION JUMPER,. WOMANS, WHITE This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all Departments and Agencies

2、of the Department of Defense. 1. SCOPE 1.1 SCO e. This specification covers the requirements for 100% polyester certifie a?- Navy twill white jumper. 1.2 Classification. Jumpers covered by this specification shall be of one type only in the following body types and lengths (see 6.2). Body type Junio

3、rs - J Misses - (no designation) Womens - W Length Petite (Short) - P Regular - R Tall (Long) - T Schedule of sizes Misses Petite (P) Regular (R) Tall (T) 4 4 4 6 6 6 8 8 8 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 20 Beneficial comments (recommendaticns, additions, deletions) and any perti

4、nent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of

5、this document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. ,e THIS DOCUMENT CONTAINS ?a PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Schedule of sizes - contd Womens (W) P

6、etite (P) Regular (R) 6 6 8 10 12 14 16 18 8 10 12 14 16 18 Juniors (J) Petite (P) 10 12 14 16 12 14 16 Tall (TI 6 8 10 12 14 16 18 Tall (T) io 12 14 16 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standars, and handbooks. The folowing specifications, standards, and handbo

7、oks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECI

8、FICATIONS FEDERAL V-B-871 V-T-276 V-T-280 NN-P-71 DDD- L- 2 O DDD-T-86 - Button, Sewing iiole, and Button, Staple (Plastic) - Thread, Cotton - Thread, Cotton, Gimp,Buttonhole - Pallet, Material Handling, Wood, Stringer - Label; For Clothing, Equipage, and Tentage (General - Tape, Textile, Cotton, Ge

9、nere1,Purpose (Unbleached, Construction, 2 Way or 4 Way (Partial) Use) Bleached, ar Dyed) . -* Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-3-24949(NU) SPECIFICATIONS MILITARY MIL-P-15011 - Pallet, Material Handling, Wood, Post Construction, M

10、IL-B-17757 - Boxes, Shipping, Fiberboard (Modular Sizes) MIL-T-43548 - Thread, Polyester Core: Cotton- , Rayon- , MIL-C-87052 - Cloth, Twill, Polyester, White 4 Way Entry Polyester-Covered STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and

11、Tables for Inspection by MIL-STD-129 MIL-STD-147 - Palletized Unit Loads MIL-STD-2073-1- DOD Materials Procedures for Development and MIL-STD-2073-2- Packaging Requirements Codes Attributes - Marking for Shipment and Storage Applications of Packaging Requirements (Unless otherwise indicated, copies

12、of federal and military specifications, - standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawi

13、ngs, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. US POSTAL SERVICE MANUAL (Copies may be obtained from the Superintendent of the Documents, U.S. Government Printing Office, Washington, DC 20

14、402-0001.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwis

15、e specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-247LI9 84 M 9777906 0385254 7 MIL-J-24949(NU) NATIONAL MOTOR FR

16、EIGHT TRAFFIC ASSOCIATION, INC., AGENT I National Motor Freight Classification I (Application for copies should be addressed to the American Trucking I Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Class

17、ification (Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades for Buttons Department of Defense Standard Shades for S

18、ewing Threads (Application for copies of color cards should be addressed to the Color Association of9the U.S., 343 Lexington Avenue, New York, NY 10016-0927.) . (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. Th

19、ese documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this document, ho

20、wever, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide Sam le. Samples, when furnished, are solely for guidance and Variations from this specification 3.2 First article. When specified, the contractor shall furnish sample informatio

21、n -fi- to t e contractor (see 6.3). may appear in the sample in which case this specification shall govern. unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Ma terial. 3.3.1 Basic material. The material for the jugper shall be a polyester twill cloth shade white 3006 conformi

22、ng to MIL-C-87052. 3.3.2 Ta e, cotton. The cotton tape for the hanger loops shall conform to type. II, c ass inch width of DDD-T-86. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-249Lt9 Lt M 9999906 035255 O O 3.3.3 Thread. 3.3.3.1 Thread,

23、covered, polyester. The thread for seaming and stitching shall be cotton covered or rayon covered polyester, shade white AH, Cable No. 66050, Ticket No. 24, 50, and 70, 2 or 3 ply and for crowtack stitching Ticket No. 50, 2 or 3 ply conforming to MIL-T-43548. The Cable No. shall conform to the Depar

24、tment of Defense Standard Shades for Sewing Threads. The use of polyester-covered polyester core thread is not allowed. 3.3.3.1.1 Automatic pocket machine. When an automatic pocket machine using a 101 stitch type is used, the thread shall be type IC2, Ticket No. A, 3 ply conforming to V-T-276. When

25、an automatic pocket machine using a 301 stitch type is used, the thread shall be Ticket No. 50, 2 or 3 ply conforming to MIL-T-43548. The Cable No. shall be as stated in 3.3.3.1. 3.3.3.2 Colorfastness. The thread shall show discoloration to light and laundering equal to or better than the standard s

26、ample when tested as specified in V-T-276 or MIL-T-43548. As a limit of acceptability or when no standard sample is available, the thread shall show a minimum of llgoodll discoloration to light and laundering when tested as specified in V-T-276 or MIL-T-43548. 3.3.4 Button. The button for the inside

27、 swing pocket shall be 22-line and conform to type III class D, style 19 of V-B-871. The color of the button shall be White, Shade BA, Cable No. 62031 in accordance with the Department of Defense Standard Shades for Buttons. 3.3.5 Gim cotton. The cotton gimp for reinforcing buttonholes shaIl be blea

28、ched able No. 66050 in accordance with the Department of Defense Standard Shades for Sewing Threads and shall conform to type I or II, size no. 8 of V-T-280. 3.3.5.1 Colorfastness. The gimp shall be equal to or better than the standard sample when tested for discoloration to laundering. As a limit o

29、f acceptability or when no standard sample is available, the gimp shall show a minimum rating of “good“ when tested for discoloration to laundering as specified in V-T-280. e 3.3.6 Combination label. Each jumper shall have a combination identification, personnel, and instruction label conforming to

30、type VI, classes 10 and 15 of DDD-L-20. The printing shall show fastness to laundering and shall bear the following inscription and format: NAME : SERVICE NO: JUMPER, WOMANS, WHITE FIBER CONTENT: 100% POLYESTER NAME OF CONTRACTOR: NAME OF MANUFACTURER: CONTRACT NO: DLA-100-00-0-0000 (EXAMPLE) (IF DI

31、FFERENT THAN CONTRACTOR) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- - MIL-J-24747 84 777770b 0385256 2 MIL-J-24949(NU) MACHINE WASHING Machine wash. Permanent press cycle, hot wash. Do not mix colors. Fill machine with clothes to 213 capaci

32、ty. Use heavy duty soap or detergent. Prespot stains with a laundry stain pretreatment. If needed, use a non-chlorine bleach. Tumble dry using a warm setting or shape and hang dry. Remove at once from dryer. If touch-up ironing is needed, use a warm iron, press jumper inside-out. OR Follow NAVEDTRA

33、Manual 414-01-45-81, Formula II. 3.3.6.1 Size label. Each jumper shall have a size label conforming to type IV or VI, Class 2 of DDD-L-20. The label shall be sufficiently sized to indicate size (body type and length) and stock number. The inscription shall be as follows: Size: 14JT (Example - 14 Jun

34、ior Tall) or 14T (Example - 14 Misses Tall) Stock Number 8410-00-000-0000 (Example) NOTE: Abbreviations for the applicable lengths shall be P for Petite, R for Regular, and T for Tall. Abbreviations for the applicable body types shall be J for Juniors and W for Womens. 3.3.6.2 Removable size ticket.

35、 Each jumper shall have a commercial type size ticket attached to the outside of the lower left sleeve. The ticket shall be 1-1/2 inches long and 2 inches high, made of a suitable plain white cardboard. The corners of the ticket may be double perforated for ease in tacking. The size (14R - Example)

36、shall be printed or stamped on the upper left hand corner in black or blue ink. The lettering for the size shall be 114 inch in height. Abbreviations for lengths shall be allowed in accordance with 3.3.6.1. 3.4 Desi n, The -jumper shall be of the pull-over type having a one piece iront an -+ a one p

37、iece back, a plain square sailor collar, a lrVl neck, one piece sleeves and finished at the bottom with turned-up hems. There shall be one double welt type pocket on the left front and one dummy (closed) double welt type pocket on the right front which shall have an inside swing pocket and button fl

38、ap closure (see Figures 1 and 2). . 3.4.1 Figures. The figures are furnished for information purposes only. To the extent of any inconsistencies between the specification and the figures, the specification shall govern. 3.5 Patterns. Standard patterns to be used to cut working patterns will be furni

39、shed by the Government (see 6.3 and 6.6). The working patterns shall be identical to the Government patterns. Neither the Government patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns. Also,

40、minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the dimensional, serviceability, or appearance requirements cited in the specification. The patterns allow a 1/2 inch seam allowance for double lapped and double stitched seams, or f

41、or safety-stitched, double needle topstitched seams. 6 - _- - 7 f- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-24949(NU) The component parts for the jumper shall be cut from in accordance with the following pattern parts: Mat er ia1 Pattern

42、 parts Cut parts Cloth, polyester twill Back Front Sleeve Topcollar Undercollar Inside pocket (right front) Outside pocket (left front) Pocket welt 3.6 Construction. 3.6.1 Stitches, seams, and stitchings. Stitch, seams, and stitching types specified in Table I shall conform to FED-STD-751. Wherever

43、two or more methods for seam or stitch types are given for the same part of the operation, any one of them may be used. Where stitch type 401 is used, the looper (underthread) shall be on the inside of the jumper. Unless otherwise specified, double needle stitching shall be 114 (+ 1/16) inch gauge w

44、ith the outer row of stitching 1/16 to 118 inch from the Finished edge. Topstitching and edge stitching shall be 1/16 to 118 inch from edge, unless otherwise specified in Table I. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, or puckers or open se

45、ams result. All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. O 3.6.2 Thread breaks and ends of seams. Ends of all seams and stitchings when not caught in other seams or stitchings shall be backtacked not less than 3/8 inch. The

46、 ends of a continuous line of stitching (except labels) shall be overlapped not less than 112 inch. The ends of label stitching shall be overlapped not less than 3 stitches. Thread breaks (all stitch types) shall be secured by stitching back of the break not less than 1/2 inch. Skipped stitches or 4

47、01 stitch type thread breaks may be repaired by using 301 stitch type. When stitch type 401 is permitted as an option, it shall not be used unless the ends are caught in other seams or stitching. As an exception, when closing the sides of the pockets, stitch type 401 may be used and a 1/4 to 3/8 inc

48、h chain shall extend beyond the ends not caught in other stitching, During the overedge operations, a knife shall be used for trimming off only the loose thread ends. The bight of the overedge stitching shall be 3/16 inch. 3.6.3 Stitches per inch. The minimum and maximum number of stitches per inch

49、shall be as specified in Table I. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_._s_ _- MIL-J-24747 4 W 777770b 0385258 b W 3 7 Manufacturing operat ions requirements. The jumper shall be manufactured in accordance with the operation requirements specified in Table I, The contractor is not required to- follow the-exact sequence of operations as listed, pro