NAVY MIL-I-7802 A-1967 INDICATORS MS28088 TURN AND SLIP (THREE PHASE)《MS28088指标转折和支路(三相)》.pdf

《NAVY MIL-I-7802 A-1967 INDICATORS MS28088 TURN AND SLIP (THREE PHASE)《MS28088指标转折和支路(三相)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-I-7802 A-1967 INDICATORS MS28088 TURN AND SLIP (THREE PHASE)《MS28088指标转折和支路(三相)》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、M IL-I-78O2A (AS) 14 January 1967 SUPERSE DING MIL-I- 78 02( Aer) 4 February 1952 MILITARY SPECIFICATION INDICATORS, MS28088, TURN AND SLIP (THREE PHASE) This specification has been approved by the Naval Air Systems Command, Depart- ment of the Navy. 1. SCOPE 1.1 Scope - This specification covers de

2、sign and all performance requirements for procurement of turn and slip indicators operated on three phase alternating current. 1.2 following types : Classification - The turn and slip indicators shall be of the MS28088-1 Type I, 26V, 3 , 400 cps, 2 min turn . MS28088-2 Type II, 115V, 3 $, 400 cps, 2

3、 min turn MS28088-3 Type III, 26V, 3 , 400 cps, 4 min turn MS28088-4 Type IV, 115V, 3 , 400 cps, 4 min turn 2. APPLICABLE DOCUMENTS 2.1 General - The following documents of the issue in effect on the date of invitation for bids form a part of this specification to the extent specified herein: SPECIF

4、ICATIONS Federal BB-N-411 Nitrogen, Technical Military MIL-P- 116 Preservation, Methods of i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I- 78 O 2 A( AS) Military (Continued) MIL- G- 174 Glass, Optical MIL-C- 5015 Connectors, Electric “AN“ Ty

5、pe MIL-IV- 5088 Wiring; Aircraft, Installation of MIL-E- 5272 Environmental Testing, Aeronautical and Associated Equipment, General Specification for MIL- E- 5400 Electronic Equipment, Aircraft, General Specification for MIL-T-5422 MIL-1-6 181 MIL-P-79 36 MIL- T- 18 3 O 3 MIL-N-18307 STANDARDS Feder

6、al FED-STD-595 Military Testing, Environmental, Aircraft Electronic Equipment Interference Control Requirements, Aircraft Equipment Parts and Equipment, Aeronautical, Preparation for Delivery Test Procedures, Preproduction and Acceptance for Aircraft Electronic Equipment, Format for Nomenclature and

7、 Nameplates for Aeronautical Electronic and Associated Equipment Colors MIL-STD-704 Electric Power, Aircraft, Char ac t e ristics and Utilization of MIL-STD- 781 Reliability Tests, Exponential Distribution MIL-STD- 794 Parts and Equipment, Procedures for Packaging and Packing of 2 /- - I Provided by

8、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-7802A 66 7777706 0126510 O MIL-I- 7802A(AS) * Military (Continued) - MS28088 Indicator, Turn and Slip (Three-phase) MS33558 Numerals and Letters, Aircraft Instrument Dial, Standard Form of 2.2 Availability o

9、f Documents - When requesting specifications, standards, drawings, and publications refer to both title and number. Copies of this specification and applicable specifications required by contractors in connection with specific procurement functions may be obtained upon application to the Commanding

10、Officer, Naval Supply Depot, Code 105X, 5801 Tabor Avenue, Philadelphia, Pennsylvania 19120. 3. REQUIREMENTS * 3.1 Preproduction - This specification makes provision for preproduction testing. * 3.2 Parts and Materials - In the selection of parts and materials, fulfillment of major design objectives

11、 shall be the prime consideration. Parts and materiais requirements shall conform to MIL-E-5400 except as otherwise specified herein. * 3.2.1 Nonstandard Parts and Materials Approval - Approval for the use of nonstandard parts and materials shall be obtained as outlined in MIL-E- 5400. * 3.3 Design

12、and Construction - The indicator shall conform with all the applicable requirements of MIL-E-5400 for design, construction and workmanship, except as otherwise specified herein. The indicator shall be designed to prevent fogging on the inside of the cover glass under extremes of atmospheric conditio

13、ns. The means provided shall be subject to approval by the Naval Air Systems Command. The sensitive elements of all type indicators shall be mounted so that they react only to turns about a vertical axis. Indicators shall be so constructed as to withstand the normal shocks, vibrations and such other

14、 conditions as are incident to service, shipping, storage, and installation, without failure. The indicator shall be suitable for front or rear mounting on the instrument panel. 3.3.1 Total Weight - The total weight of the indicator shall not exceed 1-3/4 pounds. 3 Provided by IHSNot for ResaleNo re

15、production or networking permitted without license from IHS-,-,-I MIL-I-7802A 66 7777706 OL2b5LL 2 3.3.2 Reliability - * 3.3.2.1 Operational Stability - The indicator shall operate with satisfactory performance, continuously or intermittently for a period of at least 2500 hours without the necessity

16、 for readjustment of any controls which are inaccessible to the operator during normal use. * 3.3.2.2 Operating Life - The indicator shall have total operating life of 25,000 hours with reasonable servicing and replacement of parts. Parts requiring scheduled replacement shall be specified by the con

17、tractor. * 3.3.2.3 Reliability in Mean Time Between Failure (MTBF) - The indicator shall have 2000 hours of mean (operating) time between failures when tested and accepted as outlined under the requirements of 4.4.3. 3.3.3 Cabling and Connections - * 3.3.3.1 Cables and Connectors - The indicator sha

18、ll provide for the use of cables and connectors in accordance with MIL-E-5400. The electric connector shall be a sealed connector in accordance with MIL-C-5015 and the type shall conform to MS28088. * 3.3.3.2 Interconnection Cabling - The indicator shall be capable of satisfactory operation using ex

19、ternal wiring in accordance with the applicable requirements of MIL-W-5088. The external wiring shall be unshielded, except that a minimum number of the individual wires may be shielded when demonstrated as necessary to meet interference control requirements and provided the assembly of the cable to

20、 its plugs may be easily accomplished. External cables and that portion of the connectors attached to the cables shall not be supplied as part of the indicator. * 3.3.4 Interchangeability of Reordered Indicators - For reordered indicators interchangeability shall exist between units and all replacea

21、ble assemblies, subassemblies, and parts of a designated model of any previously manufactured equipment, supplied or designated by the procuring activity. * 3.3.5 Interference Control - The generation of radio interference by the indicator and the vuinerability of the indicator to radio interference

22、 shall be controlled within the limits of MIL-1-6181. * 3.3.6 Maintenance Provisions and Field Testing - Provisions for maintenance shall be as specified in MIL-E-5400. Specific test points and test facilities shall be provided to the greatest extent practicable for ease of field testing and mainten

23、ance. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- I- 7 8 02A( AS) * 3.3.7 Nameplate - Nameplate approval for indicator identification shall be in accordance with MIL-N-18307. * 3.3.8 Standard Conditions - The following conditions shall be

24、used to establish normal performance characteristics under standard conditions and for making laboratory bench tests. Temperature Room ambient (25 *5 C) Pressure Normal atmospheric (approximately 29.92 inches Hg. ) Altitude Normal ground Vibration None Humidity Room ambient up to 90 percent - relati

25、ve humidity Input power voltage .5 21.0 V AC or 27.5 +O.g AC - * 3.3.9 Service Conditions - The indicator shali operate satisfactorily under any of the environmental service conditions or reasonable combination of these conditions as specified in MIL-E-5400 for Class 2 equipment, except as modified

26、herein. * 3.3.10 Primary Input Power Requirements - The indicator shall meet all applicable requirements of MIL-STD-704 and shall give specified per- formance from the following power sources with characteristics as defined in MIL-STD-704 having limits as specified therein. The power required shall

27、not exceed the specified amounts: (1) The Type II and IV indicators shall operate on AC power (three phase) 115V, 400 cps, category “B“, 40 milli- amperes. (2) The Type I and III indicators shall operate on 26 V, 400 cps, proportional to category “B“, 175 milliamperes. * 3.3.10.1 Degraded Performanc

28、e - Degraded performance will be permitted for voltage transients not exceeding O. 5 second during normal electric system operation. Operation shall return to normal with no resulting damage to the indicator. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

29、 IHS-,-,-* 3.4 Performance - Unless otherwise specified, values set forth to establish the requirements for satisfactory performance apply to performance under both standard and extreme service conditions, When reduced performance under the extreme conditions is acceptable, tolerances or values sett

30、ing forth acceptable variations from the performance under the standard conditions will be specified. 3.5 Detail Requirements - * 3.5.1 Case - The case shall conform to MS28088. * 3.5.1.1 Hermetic Sealing - The case shall provide a hermetically sealed enclosure for all of the mechanism. The case sha

31、ll be so constructed that it may be opened, the mechanism removed and replaced and the case re- sealed at least three times. This shall be possible without the use of any special tool, jig or fixture, unless such device is specifically approved by the procuring activity, The sealing of the case shal

32、l not be dependent upon any material which will be adversely affected by an atmosphere to which the instrument may be subjected in normal use in military aircraft. * 3.5.1.2 Filling Medium - The filling medium shall be a mixture of 90 percent nitrogen and ten percent helium. The nitrogen used shall

33、be in ac- cordance with BB-N-411, Type I, Class I, Grade C. The filling medium shall contain not more than O. 006 milligram of water vapor per liter (dew point -65 C) at the filling pressure. The absolute pressure of the filling medium in the case shall be 1 kO.1 atmosphere. * 3.5.1.3 Body-The body

34、shall be made either of non-ferrous low density metal, or of plastic material, shall be uniform in texture having a smooth surface and shall be hermetically sealed. The case shall be finished with a lusterless black material, Color No. 37038 of FED-STD-595. The finishing material shall be of a durab

35、le type to withstand usage encountered in service. The plastic material shall be of the thermosetting type composed of a suitable filler and phenol condensation binder. x 3.5.1.4 Bezel Ring - The bezel ring shall be made of non-ferrous low density metal and shall be finished with a lusterless black

36、material Color No. 37038 of FED-STD-595. The finishing material shall be of a durable type to withstand usage encountered in service. * 3.5.1.5 Cover Glass - The cover glass shall be in accordance with MIL-G-174 (Optical Glass 523-586). Any flaws permitted by MIL-G-174 shall not interfere with readi

37、ng of the dial. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-7802A 66 7777706 OL265Lq 8 MIL-I- 7802A( AS) * 3.5.2 - Dial - The did shall consist of a turn indicator and slip indicator and shaU conform to Figure 1. All markings shall be dur

38、able to withstand the usage encountered in service. The style and proportions of the numerals and letters placed on the dial shall conform to MS33558. 3.5.3 slip Indicator - * 3.5.3.1 Indicator Tube - The slip indicator tube shall be clear annealed glass tubing free from any flaws that will affect t

39、he readability of the inclinometer. The wall thickness shall be not less then 3/64 inch and the inside of the tube shall be smooth and uniform in order that the bail will roll . smoothly. * 3.5.3.2 indicator Ball - The ball shall be of white glass or other material approved by the procuring activity

40、. The white color shall be in ac- cordance with Color No. 37875 of FED-STD-595. The ball shall be a highly polished sphere 7/16 +1/64 inch in diameter. 3.5.3.3 Damping Liquid - The damping liquid used in the slip indicator shall be colorless so that it will not interfere with the silhouette illumina

41、tion of the bail by the black backing of the indicator tube. 3.5.4 Turn Indicator - * 3.5.4.1 Pointer - The turn indicator pointer, the center mark, and the deflection marks shall conform to Figure 1. No portion of the pointer shall obstruct the view of the slip indicator tube. The pointer shall be

42、firmly attached to the mechanism and shall be as Iight as practicable, and rigid to prevent oscillation under vibration, and readily adjustable. 3.5.4.2 Mechanism Adjustment - Means shall be provided to adjust or correct the sensitivity and the damping of the indications. When the adjusting means is

43、 set in the neutral position, one quarter part of the total range of adjustment shall be available in either direction. This means of adjustment shall be reasonably simple to manipulate without special tools. 3.5.4.3 Gyro Parts - The gyro parts shall be mounted so that the instrument cover may be re

44、moved without disturbing the adjustments. * 3.5.4.4 Insulation - The complete electrical system shali be insulated from the indicator case and be capable of withstanding a voltage of 500 V DC for a period of five seconds. 3.5.4.5 Power Failure Indicator - A suitable type indicator shall be incorpora

45、ted to indicate improper phase rotation, or loss of voltage or current in any of the three phases of the gyro motor. When current or power failure occurs in any of the three phases, the indicator shall read “OFF“. When power is applied and current is flowing in each leg, the flag shall disappear. 7

46、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-7802A 66 7777906 OL265L5-T W LINES MARKING ZERO POSITION OF BALL REAR HALF AND BOTTOM OF SLIF INDICATOR OR UNSHADED PORTION OF POINTER POWER FAILWE FLAG SUITABLE CARD BEHIND INCLINOMETER BACKGROUN

47、D OF DIAL MILI-7802A (AS) LUSTERLESS BLACK COLOR NO. 37038 OF FED-STD-595 . .438 I.03k.r-c 4 -. O31 +. 005 t .I .438 f. 031 .O31 I.005 +.O3 .O31 ,031 +.O05 .O31 *.O0 TYPE I AND II DIAL TYPE III AND IV DIAL POINTER CENTER MARK DEFLECTION MARK DIMENSIONS IN INCHES UNLESS OTHERWISE SPECIFIED. TOLERANCE

48、S: DECIMALS f. 02 ANGLES +1/2“ MARKING FINISH I CENTER MARK I LUSTERLESS WHITE COLOR NO. 37875 OF DEFLECTION MARK SHADED PORTION OF POINTER LETTERING, OFF FED- STD-595 LETTERING, 2-MIN TURN, 4-MIN TURN Figure 1. Markings, dial and pointer Provided by IHSNot for ResaleNo reproduction or networking pe

49、rmitted without license from IHS-,-,-MIL-I-7802A 66 7797706 OI2b5Ib I MIL-I- 7802A(AS) 4. QUALITY ASSURANCE PROVISIONS * 4.1 Responsibility for Inspection - Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of ali inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory ac