NAVY MIL-F-18264 D (2)-1994 FINISHES ORGANIC WEAPONS SYSTEM APPLICATION AND CONTROL OF《武器系统有机饰面的应用及控制》.pdf

《NAVY MIL-F-18264 D (2)-1994 FINISHES ORGANIC WEAPONS SYSTEM APPLICATION AND CONTROL OF《武器系统有机饰面的应用及控制》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-F-18264 D (2)-1994 FINISHES ORGANIC WEAPONS SYSTEM APPLICATION AND CONTROL OF《武器系统有机饰面的应用及控制》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-F-IIZD (2) 9999906 1980456 054 I INCH - POUND I MIL-F-18264D AMENDMENT 2 31 MAY 1994 SUPERSEDING AMENDMENT 1 23 APRIL 1971 MILITARY SPECIFICATION FINISHES: ORGANIC, WEAPONS SYSTEMS, APPLICATION AND CONTROL OF This amendment forms a part of MIL-F-l8264D, dated 22 JULY 1968, and is approved for us

2、e by all Departments and Agencies of the Department of Defense. PAGE 1 * 2.1, Under “Specifications - Federal ,“ ADD: “0-A-51 - Acetone, Technical P-D-680 - Dry Cleaning and Degreasing Sol vent QQ-P-35 - Passivation Treatments for Corrosion Resistant Steel TT-P-28 - Paint, Aluminum, Heat Resisting (

3、1200OF) TT-T-266 - Thinner: Dope and Lacquer (Cellulose-Nitrate) TT-E-489 - Enamel, Alkyd, Low VOC Content TT-E-527 - Enamel, Alkyd, Lusterless, Low VOC Content TT-E-529 - Enamel, Alkyd, Semigloss, Low VOC Content TT-N-95 - Naphtha, Aliphatic TT-P-1757 - Primer Coating, Zinc Chromate, Low-Moisture-S

4、ensitivity“ * Bottom of page, ADD the following “Beneficial comment block“ and Form DD1426 (see last page of this amendment) to the back of the document: Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addres

5、sed to: Commander, Naval Air Warfare Center Aircraft Division, Code SR3, Highway 547, Lakehurst, NJ 08733-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA 1 of 10 FSC 8010 DISTRIBUTION STATEMEN

6、T A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-L8264D (2) m 9999906 L980857 T90 m MIL-F-18264D AMENDMENT 2 PAGE 2 * 2.1 Under “Specifications - Federal, II DELETE: “TT-E-776, TT-B-84

7、6, and TT-R-771“ PAGE 3 * 2.1, Under “Specifications - Military,“ DELETE: “MIL-C-5410, MIL-D-5549, MIL-D-5550, MIL-D-5551, MIL-E-5556, MIL-C-7439, MIL-S-7502, MIL-E-7729, MIL-D-7850, MIL-P-8585, MIL-P-14276, MIL-C-18263, MIL-L-19537, MIL-T-19544, MIL-C-22543, MIL-C-81773“ MIL-C-22751, MIL-M-25047, M

8、IL-C-27315, MIL-P-52192, MIL-E-52227, and * 2.1, Under “Specifications - Mil i tary,“ ADD: “DOD-P-15328 - Primer (Wash), Pretreatment (Formula No. 117) For Metals) MIL-C-43616 - Cleaning Compound, Aircraft Surface MIL-P-53022 - Primer, Epoxy Coating, Corrosion Inhibiting, Lead and MIL-P-53030 - Prim

9、er Coating, Epoxy, Water Reducible, Lead and Chromate MIL-L-52043 - Lacquer, Semi G1 oss, Ce1 1 Ulose Ni trate MIL-C-81706 - Chemical Conversion Materials for Coating Aluminum and MIL-C-81772 - Thinner, Aircraft Coating MIL-C-83286 - Coating, Urethane, Aliphatic Isocyanate, For Aerospace Appl i cat

10、ions MIL-C-83231 - Coatings, Polyurethane, Rain Erosion Resistant, for Exterior Aircraft and Missile Plastic Parts MIL-C-83445 - Coating System, Polyurethane, Non Yellowing, White, Rain- MIL-C-85285 - Coating: Polyurethane, High-Solids MIL-P-85582 - Primer Coatings: Epoxy, Waterborne“ (Metric) Chrom

11、ate Free Free Al umi num Al 1 oys Erosion Resistant, Thermally Reflective PAGE 6 * 2.1, Under “Standards“ ADD “Military“ and “MIL-STD-2161 - Paint Schemes and Exterior Markings for U.S. Navy and Marine Corps Aircraft“ 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

12、ense from IHS-,-,-MIL-F-182640 AMENDMENT 2 PAGE 7 * 4. l. 1, a. : DELETE and SUBSTITUTE: “4.1 .l, a. Wash primer or pretreatment coating, MIL-C-8514, may be used on corrosion resistant steel surfaces which cannot be freshly passivated in accordance with QQ-P-35 prior to application of primer coating

13、. It should not be used on metal that becomes heated over 30OOF. Directions for application under various condition of humidity shall be in accordance with MIL-C-8507.“ PAGE 8 * 4.1.1, b.: DELETE and SUBSTITUTE: “4.1.1, b. Epoxy primer, MIL-P-23377 or MIL-P-85582, is used as an undercoat for epoxy a

14、nd polyurethane topcoats. MIL-P-85582 is not for use in wet installation of fasteners, slip fits, or press fits. MIL-P-85582 may cause flash rusting on bare steel. For both specifications, use only material purchased under the latest revision. * 4. l. 1, d. : DELETE and SUBSTITUTE: “4.1.1, d. Zinc c

15、hromate primer coating, TT-P-1757, used as a one component, alkyd based, corrosion inhibiting primer coating on surface- treated aluminum and on substrates coated with wash primer conforming to MIL-C-8514 or DOD-P-15328. It is used as an alternate to MIL-P-23377 in the wet installation of fasteners,

16、 slip fits, and press fits.“ 4.1.1, e.: DELETE and SUBSTITUTE: “4.1.1, e. Epoxy topcoat, MIL-C-22750, is used on weapons systems as a highly resistant finish to chemicals and solvents.“ * 4.1.1, k.: DELETE and SUBSTITUTE: “4.1.1, k. Miscellaneous. MIL-P-53022, MIL-P-53030, MIL-L-52043, and TT-E-529

17、are frequently used coatings for the U.S Army Missile and Tank and Automotive Command.“ * 4. l. 1: ADD the following NEW paragraph “1 II: “4.1.1, 1. Polyurethane coatings, MIL-C-85285 and MIL-C-83286, are highly weather resistant coatings used as the standard topcoat over the primer coating MIL-P-23

18、377 or MIL-P-85582.“ 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-18264D (2) D 7999906 L980859 863 MIL-F-18264D AMENDMENT 2 PAGE 9 * 4.2.3, line 3, DELETE “MIL-P-8585“ and SUBSTITUTE “TT-P-1757.“ PAGE 10 * TABLE I: DELETE entry for “MIL-P-

19、8585“ in its entirety. PAGE 11 TABLE I: DELETE “MIL-E-7729, Types I and II,“ and SUBSTITUTE “TT-E-489;“ DELETE “MIL-E-5556“ and SUBSTITUTE “TT-E-527. II PAGE 12 * TABLE I: DELETE entries for “Polyurethane topcoat, MIL-C-81773,“ “Epoxy primer, MIL-P-23377,“ “Epoxy topcoat, MIL-C-22750,“ and “Dopes, M

20、IL-D-5549, MIL-D-5550, MIL-D-5551, and MIL-0-7850,“ in their entirety. PAGE 13 * 5.1.2, 1 ine 9: DELETE “0-T-620, I and SUBSTITUTE “P-D-680, O-A-51, or TT-N-95. I PAGE 14 * 5.1.3.1, lines 1 through 5: DELETE first sentence and SUBSTITUTE: “Using MIL-C-38334, remove surface oxides and trace contamina

21、nts on al uminum and magnesi um surfaces after cleaning operat ions (see 5.1.3) while surfaces are still wet. II PAGE 15 5.1.5, line 3, sentence 2: DELETE and SUBSTITUTE: “Al uminum surfaces shall be treated to produce coatings conforming to MIL-C-5541, Class 1A or 3.“ 4 Provided by IHSNot for Resal

22、eNo reproduction or networking permitted without license from IHS-,-,-MIL-F-18264D AMENDMENT 2 PAGE 16 * 5.2.1, lines 1 through 2: DELETE first sentence and SUBSTITUTE: “Unless otherwise specified in the contract or purchase order, the epoxy primer coating and polyurethane topcoat is the standard co

23、ating system.“ PAGE 17 * TABLE II, DELETE all references to “MIL-P-8585.“ * TABLE II, DELETE entries for polyurethane coating “MIL-C-81773“ and “MIL-C-83286“ and SUBSTITUTE: E System Topcoat Pr i mer Wash primer EpoxylPolyurethane MIL-C-85285 or MIL-P-23377 or -“ MIL-P-85582 MIL-C-83286 TABLE II, bo

24、ttom row, column 4: DELETE “MIL-E-7729 or MIL-E-5556,“ and SUBSTITUTE “TT-E-489 or TT-E-527. PAGE 18 * TABLE III, for MIL-P-23377, DELETE “Apply a crosscoat in accordance with MIL-C-22751,“ and SUBSTITUTE “Apply to a dry film thickness of 0.6 to 0.9 mils in two coats.“ * TABLE III, DELETE all refere

25、nces to MIL-C-81773, MIL-C-83286, and MIL-C-22751, and SUBSTITUTE: I Operat i on Comment I Speci fi cat i on Epoxy Primer/ MIL-C-85285 Apply topcoat to a total dry film Polyurethane Topcoat or thickness of 1.7 to 2.3 mils MIL-C-83286 5 Provided by IHSNot for ResaleNo reproduction or networking permi

26、tted without license from IHS-,-,-MIL-F-18264D AMENDMENT 2 PAGE 20 * 5.3. l. IC. : DELETE “MIL-C-18263“ and SUBSTITUTE “MIL-STD-2161 .It * 5.3.2.1, line 5 and 12: DELETE “MIL-R-7439 or MIL-C-27315“ and SUBSTITUTE “MIL-C-83231 or MIL-C-83445.“ PAGE 21 5.3.2.3, line 2: DELETE “MIL-E-7729, Type III,“ a

27、nd SUBSTITUTE “TT-E-489.“ PAGE 22 * 5.4, beginning at the end of the top line of page: DELETE “.0.0006 to 0.0009 inch for one cross coat of epoxy primer, 0.0010 to 0.0015 inch total dry film thickness of polyurethane topcoat conforming to MIL-C-81773, 0.0017 to 0.0023 inch total dry film thickness o

28、f polyurethane topcoat conforming to MIL-C-83286, and 0.0011 to 0.0015 inch for one mist coat plus one wet coat of epoxy topcoat.“ and SUBSTITUTE “.total dry film thickness of 0.0006 to 0.0009 inch (0.6 to 0.9 mils) for epoxy primer coating MIL-P-23377 or MIL-P-85582 applied in one or two coats, tot

29、al dry film thickness of 0.0017 to 0.0023 inch (1.7 to 2.3 mils) for polyurethane topcoat MIL-C-85285 or MIL-C-83286 or epoxy topcoat MIL-C-22750.“ * 5.6.2.1: DELETE paragraph in its entirety. PAGE 23 * 5.6.3: DELETE paragraph in its entirety. * ADD new paragraph 5.6.2.4: “5.6.2.4 Polyurethane syste

30、m. Polyurethane topcoat, MIL-C-85285 or MIL-C-83286, is to be spray applied over epoxy primer coating, MIL-P-23377 or MIL-P-85582, which has been allowed to dry for 1 to 2 hours. The dry film thickness of the primer coating shall be 0.6 to 0.9 mils. The topcoat is to be applied in accordance with ta

31、ble III.“ 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-18264D (2) 99999Ob 19808b2 358 D MIL-F-18264D AMENDMENT 2 PAGE 24 * 5.8.2.1: DELETE paragraph in its entirety. *5.8.3, 1 ine 3: DELETE “MIL-C-18263“ and SUBSTITUTE “MIL-STD-2161.“ PAGE

32、 28 * 5.12, lines 1 through 5: DELETE first two sentences and SUBSTITUTE: “For Department of the Navy aircraft, insignia and markings shall be applied in accordance with MIL-STD-2161.“ 7.1, second sentence: DELETE second sentence and SUBSTITUTE: “The anodized surface, in addition, shall be manually

33、treated with materials conforming to MIL-C-81706 to produce coating conforming to MIL-C-5541, manually appl ied. II PAGE 29 7.1, top of page:DELETE “MIL-E-7729 or MIL-E-5556“ and SUBSTITUTE “TT-E-489 or TT-E-527. I 8.1, end of paragraph: ADD the following: “When examined visually, the coating shall

34、be free from runs, sags, scratches,voids, excessive orange peel, inclusions and other film irregularities. In addition, when examined by means of a minimum 6X magnification lens, there shall be no evidence of microcracks, except that after flight test , slight microcracks around highly stressed fast

35、eners shall not be cause for rejection.“ PAGE 33 * 12.2, middle of page: DELETE third and fourth sentences, and SUBSTITUTE: “Originally applied, aged, epoxy primer coating, MIL-P-23377 or MIL-P-85582, may be used as a base for subsequent topcoats by applying a thin coat (0.2 to 0.5 mil dry film thic

36、kness) followed by application of an epoxy primer epoxy or polyurethane topcoat. The aged primer coating should be lightly scuff sanded with aluminum oxide paper.“ 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-13.6d., second “Limited resi stan MI

37、L-F-18264D AMENDMENT 2 PAGE 35 sentence: DELETE and SUBSTITUTE: in use for bondina the standard finishina systems t steel surfaces aid high strength steel with cadm to corrosion ium plate, if the latter does not receive a spplemental chemical treatment. Wash primer conforming to MIL-C-8514 is essent

38、ial as a tie coat between the metal and coating systems using MIL-P-7962.“ PAGE 40 14.1, l3/, a. : DELETE al 1 references to “MIL-C-22543“ and SUBSTITUTE “MIL-C-43616.“ 14.1, l3/, b.: After “0.25,“ ADD “percent.“ Page 55 * 14.1, 3l/: DELETE in its entirety and SUBSTITUTE: “31/ The wet adhesion of ep

39、oxy primer coating (MIL-P-23377 or ME-P-85582) has been found to be inadequate, compared to conventional anodic coatings produced from chromic acid; for this reason, additional treatment with materials conforming to MIL-C-81706 to produce coatings conforming to MIL-C-5541 is required.“ PAGE 56 TABLE

40、 V: DELETE all reference to TT-R-771. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-18264D (2) m 9999906 L980864 L20 m MIL-F-182640 AMENDMENT 2 The margins of this amendment are marked with an asterisk (*) to indicate where changes (additio

41、ns, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based

42、on the entire content, irrespective of the marginal notations and relationship to the last previous amendment. Custodians: Army - ME Air Force - 11 Navy - AS Preparing activity: (Project No. 8010-0500) Navy - AS Review activities: Army - AT, MR, AR, MI, AV Air Force - 84 Navy - CG 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-