NAVY MIL-DTL-50647 B-2005 CARTRIDGE DELAY M293 ASSEMBLY《M293组延迟弹筒》.pdf

《NAVY MIL-DTL-50647 B-2005 CARTRIDGE DELAY M293 ASSEMBLY《M293组延迟弹筒》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-50647 B-2005 CARTRIDGE DELAY M293 ASSEMBLY《M293组延迟弹筒》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMIL-DTL-50647B 05 October 2005 SUPERSEDING MIL-C-50647A 23 April 1991 DETAIL SPECIFICATION CARTRIDGE, DELAY, M293 ASSEMBLY This specification is approved for use by all Departments and Agencies of the Department of Defense. This specification remains inactive for new design. It may still b

2、e used for replacement purposes. 1. SCOPE 1.1 Scope. This specification covers the requirements for the M293 Delay Cartridge (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include

3、documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4,

4、 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these d

5、ocuments are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-A-2550 Ammunition, General Specification for MIL-A-8625 Anodic Coating for Aluminum and Aluminum Alloys Comments, suggestions, or questions on this document should be addressed to Commander, Indian Hea

6、d Division, Naval Surface Warfare Center, Technical Information Branch (Code 4230), 101 Strauss Avenue, Indian Head, Maryland 20640-5035, or emailed to amanda.pennnavy.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online d

7、atabase at http:/assist.daps.dla.mil/. AMSC N/A FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-12T06:56ZCheck the source to verify that this is the current version before use.Provided by IHSNot for Re

8、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50647B 2 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-810 Environmental Test Methods and Engineering Guidelines MS-28741 Hose Assembly Detachable End Fitting Medium Pressure (Copies of these documents are available online at

9、 http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following Government drawings form a part of this specification to the extent specified herein

10、. Unless otherwise specified, the issues are those cited in the solicitation or contract. OTHER GOVERNMENT DOCUMENTS WS 21535 Ignition Devices, (Percussion), PVU-1/A DRAWINGS NAVAL ORDNANCE STATION (CAGE Codes 19200 and 19203) DL11730546 Cartridge, Delay, M293 Assembly 851AS110 Ignition Device PVU-1

11、/A 8799620 Box, Packing, Ammunition, For Cartridge, Delay: M70, M93, M113, or M155 8799621 Carton, Packing, Ammunition, For Cartridge, Delay: M70, M93, M113, or M155 9224944 Carton, Alternative, Packing, Ammunition, For Cartridge, Delay: M70, M93, M113, M155, XM231, or M293 (Application for copies s

12、hould be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Attn: Technical Information Branch (Code 4230), Indian Head, MD 20640-5035.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise sp

13、ecified, the issues of these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR QUALITY ANSI/ISO/ASQ A8402 Quality Management and Quality Assurance Vocabulary ANSI/ASQ Zl.4 Sampling Procedures and Tables for Inspection by Attributes Source: http:/assist.daps.dla.mil - Do

14、wnloaded: 2005-10-12T06:56ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50647B 3 (Copies of these documents are available online at http:/www.asq.org/ or from the Ameri

15、can Society for Quality, PO Box 3005, 611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM E1742 Standard Practice for Radiographic Examination (Copies of this document are available online at http:/www.astm.org/ or from the American Society for Te

16、sting and Materials Customer Service, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supers

17、edes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a first article sample shall be subjected to first article inspection (see 4.4, 6.2, and 6.3). 3.2 Conformance to documents. The M2

18、93 Delay Cartridge covered by this specification shall be manufactured in accordance with DL11730546 and all documents listed thereon. 3.3 Materials. All materials used in the manufacture of the cartridges shall conform strictly to the specifications referred to on the respective drawings unless spe

19、cific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.4 Components. 3

20、.4.1 Primary components. For the purpose of this specification, the PVU-1/A Ignition Device, M75 Delay Element, Igniter Charge and the cartridge propellant charge are considered primary components. Only primary components from a single lot shall be used in a production lot of cartridges; however, on

21、e primary component production lot may be used in more than one cartridge production lot. 3.4.1.1 Ignition device. The ignition device shall be furnished from lots manufactured within the preceding 24 months or recertified within the preceding 12 months. The ignition device shall be manufactured per

22、 Drawing 851AS110 and accepted per WS 21535. Prior to assembly into a cartridge, the ignition device shall be radiographically examined for defects as specified in 4.7.1. 3.4.2 Hardness. The hardness of each component part shall be in accordance with the applicable drawing (see 4.7.2). 3.4.3 Protect

23、ive finish. The finish of each component part shall be in accordance with MIL-A-8625 and the applicable drawing (see 4.7.3). 3.5 Assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-12T06:56ZCheck the source to verify that this is the current version before use.Provided by IHSNot for Re

24、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50647B 4 3.5.1 Radiographic examination. Each cartridge assembly shall be radiographically examined for defects (see 4.7.4). 3.5.2 Leak test. Each assembled cartridge shall exhibit no air leakage greater than 1 x 10-4st

25、andard cubic centimeters per second (see 4.7.5) at a 14.7 psia pressure differential. 3.5.3 Vibration. The assembled cartridge shall withstand vibration as prescribed in MIL-STD-810, Method 514.3, Test Procedure I, Test Condition I 3.2.5 without evidence of any disintegration of the ignition device,

26、 propellant, or igniter, or derangement of any component (see 4.7.7 and 6.2). 3.6 Functional requirements. 3.6.1 Ignition device sensitivity. The ignition device shall fire when drop tested at an energy level of 26 inch-ounces in a sectioned cartridge void of igniter and propellant charge (see 4.7.8

27、.1). 3.6.2 Cartridge performance. 3.6.2.1 Misfires. The cartridge shall not fail to fire. 3.6.2.2 Ballistics. The cartridge, when tested in a M120 initiator shall produce the pressures, delay times (see 6.6.1), and times to Pmax(see 6.6.2) at temperatures specified in table I (see 4.7.8.2). Pressure

28、 values shall be produced in a one cubic inch pressure station at the end of 15 feet of hose in accordance with MS-28741-4. TABLE I. Ballistic requirements. Temperature (F) Delay time (sec) Pressure (psig) Time to Pmax(ms) Lower Upper Lower Upper -60 to -70 .590 .890 700 1425 50 65 to 75 .590 .780 9

29、00 1600 50 195 to 205 .560 .780 1175 1800 50 3.7 Workmanship. Cartridges shall be free of cracks, splits, or other defects which might prevent proper mating with connecting parts or proper functioning of the device. 3.7.1 Metal defects. All components shall be free from cracks, splits, cold shuts, i

30、nclusions, porosity, or any similar defect. 3.7.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.7.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion,

31、or other foreign matter. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-12T06:56ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50647B 5 4. VERIFICATION 4.1 Clas

32、sification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.4) b. Quality conformance inspection (see 4.5) 4.1.1 Quality assurance terms and definitions. Reference shall be made to ANSI/ISO/ASQ A8402 to define the quality assu

33、rance terms used. 4.2 Inspections. Inspections shall be in accordance with MIL-A-2550 and ASTM E1742. 4.3 Inspection conditions. Unless otherwise specified in the contract or purchase order (see 6.2), inspection conditions shall be as follows: a. Temperature: Room ambient 20to 25C (68to 77F) b. Alti

34、tude: Sea level c. Humidity: 50 percent relative, maximum d. Atmospheric: 14.7 psia 4.4 First article inspection. At the beginning of regular production, the contractor shall submit a first article sample to a Government approved facility for evaluation. The sample shall consist of 21 assembled cart

35、ridges for ballistics testing including 12 for vibration tests, 5 assembled cartridges for sealant tests, 10 sets of unassembled components for dimensional and visual examination, and the quantity specified in accordance with 4.4.2, i.e., cartridges assembled without the igniter and propellant charg

36、e for ignition device sensitivity test. The first article sample shall be manufactured using the same materials, equipment, processes, and procedures as used in regular production. All parts and materials, including packaging and packing, shall be the same as used for regular production and shall be

37、 obtained from the same source of supply. When it becomes necessary to make a change in either the ignition device, propellant, or igniter lot after initial production, 12 assembled cartridges from the first production lot thereafter shall be tested in accordance with 4.7.7. The Government reserves

38、the right to require new first article samples until such time as an acceptable sample is submitted (see 6.3). 4.4.1 Examination, tests, and facility. After provisional acceptance at source, the sample shall be inspected for all requirements of the drawings and specifications at a Government laborat

39、ory or other such facility specified in the contract (see 6.2). 4.4.2 Sample size for ignition device sensitivity. The number of cartridges assembled without igniter or propellant to be submitted for ignition device sensitivity tests shall be in accordance with table II. Source: http:/assist.daps.dl

40、a.mil - Downloaded: 2005-10-12T06:56ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50647B 6 TABLE II. Ignition device sensitivity. Lot size Sample size 3 to 15 3 16 to 2

41、5 4 26 to 40 5 41 to 65 7 66 to 110 10 111 to 180 15 181 to 300 25 301 to 500 30 501 to 800 35 801 to 1300 40 Over 1300 50 4.4.3 Temperature conditioning for ballistic test. The sample shall be temperature conditioned and tested to determine compliance with 3.6.2.2. The sample for firing shall be co

42、nditioned to table III. TABLE III. Temperature conditioning. Temperature (F) Not vibrated Vibrated -60 to -70 3 4 65 to 75 3 4 195 to 205 3 4 4.4.4 First article failure. Failure of the sample to comply with the requirements of the drawings and specifications shall result in first article sample dis

43、approval. 4.5 Quality conformance inspection. 4.5.1 Lot. 4.5.1.1 Submission of product. The product shall be submitted in accordance with ANSI/ASQ Z1.4. 4.5.1.2 Lot size. Unless otherwise specified (see 6.2), the production lot size shall be not more than 600. 4.5.2 Examination and tests. The qualit

44、y conformance sample shall be subjected to the examinations of 4.6 and all the test procedures of 4.7 except for 4.7.7. 4.6 Examination. All cartridges and components shall be examined visually and radiographically and characteristics defined in accordance with the applicable drawings. One hundred p

45、ercent examination shall be performed for all critical defects. Examination for major or minor defects shall be performed on a defect basis in accordance with the classification of defects. Four power (4X) magnification may be used in performing visual examination for such defects as burrs and forei

46、gn matter. When compliance is in doubt as a result of visual inspection, the characteristic shall be measured or gaged to determine acceptability. All nonconforming items shall be rejected. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-12T06:56ZCheck the source to verify that this is the c

47、urrent version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50647B 7 4.6.1 Cartridge, Delay, M293 Assembly, Drawing 11730546. Characteristic Defect Method of Inspection Critical 1 Any part missing X-ray/Visual 2 Improper assembl

48、y X-ray/Visual 3 Mixed delay elements or propellant Visual 4 Metal defctive Visual 5 Crimp missing or incorrect Visual 6 Marking missing, incorrect, or illegible Visual Major 101 Cartridge profile failure Gage 102 Diameter of body, max Gage 103 Diameter of head, max Gage 104 Location of datum diamet

49、er Gage 105 “O“ ring split, cracked or cut Visual 106 Protective finish inadequate or defective Visual 107 Foreign matter present Visual 108 Burr Visual Minor 201 Total length, max Gage 202 Case damaged Visual 203 Varnish inadequate or missing Visual 4.6.2 Delay Element, M75, Drawing 11730545, covering a detail of Drawing 11730546. Characteristic Def