NAVY MIL-DTL-25427 3-2009 COUPLING HALF HOSE ATTACHMENT HYDRAULIC SELF-SEALING GROUND SUPPORT QUICK DISCONNECT TYPE I AND TYPE II《I和II型快速断开地面支持自密封液压软管附件半联轴器》.pdf

《NAVY MIL-DTL-25427 3-2009 COUPLING HALF HOSE ATTACHMENT HYDRAULIC SELF-SEALING GROUND SUPPORT QUICK DISCONNECT TYPE I AND TYPE II《I和II型快速断开地面支持自密封液压软管附件半联轴器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-25427 3-2009 COUPLING HALF HOSE ATTACHMENT HYDRAULIC SELF-SEALING GROUND SUPPORT QUICK DISCONNECT TYPE I AND TYPE II《I和II型快速断开地面支持自密封液压软管附件半联轴器》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-25427/3 08 December 2009 DETAIL SPECIFICATION SHEET COUPLING HALF, HOSE ATTACHMENT, HYDRAULIC, SELF-SEALING, GROUND SUPPORT, QUICK DISCONNECT, TYPE I AND TYPE II This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiri

2、ng the product described herein shall consist of this specification sheet and MIL-DTL-25427. FIGURE 1. Coupling half, hose attachment, dimensions and configuration for type I and type II. AMSC N/A FSC 4730 INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license

3、 from IHS-,-,-MIL-DTL-25427/3 2FIGURE 2. Type U fitting end in accordance with SAE-AS4395 style E design standard flared. FIGURE 3. Type V, fitting end in accordance with SAE-AS4375 style E design standard flareless. FIGURE 4. Type W fitting end in accordance with SAE-AS85421/1, style 1 design stand

4、ard beam seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-25427/3 3TABLE I. Coupling half, hose attachment dimensions for type I and type II. Thread T SAE-AS8879 Class 3A Dash No. Tube OD SAE-AS4395 flared SAE-AS4375 flareless SAE-AS8542

5、1/1 beam seal -04 0.250 0.4375-20UNJF 0.4375-20UNJF 0.4375-24UNJS -06 0.375 0.5625-18UNJF 0.5625-18UNJF 0.5625-20UNJS -08 0.500 0.7500-16UNJF 0.7500-16UNJF 0.7188-20UNJS -10 0.625 0.8750-14UNJF 0.8750-14UNJF 0.8438-18UNJS -12 0.750 1.0625-12UNJ 1.0625-12UNJ 1.0000-16UNJ -16 1.000 1.3125-12UNJ 1.3125

6、-12UNJ 1.2500-14UNJS -20 1.250 1.6250-12UNJ 1.6250-12UNJ 1.5781-14UNJS -24 1.500 1.8750-12UNJ 1.8750-12UNJ 1.8438-14UNJS TABLE I. Coupling half, hose attachment dimensions for type I and type II - Continued. A (max) B (max) Dash No. Type U Type V Type W Type U Type V Type W -04 1.660 1.560 1.367 0.5

7、65 0.463 0.290 -06 1.824 1.732 1.563 0.571 0.479 0.310 -08 1.940 1.825 1.576 0.672 0.572 0.323 -10 2.570 2.430 2.111 0.773 0.635 0.387 -12 2.450 2.270 1.983 0.879 0.698 0.427 -16 2.650 2.600 2.180 0.926 0.698 0.475 -20 2.550 2.640 2.020 0.973 0.698 0.475 -24 2.729 2.735 2.188 1.098 0.698 0.557 Provi

8、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-25427/3 4TABLE I. Coupling half, hose attachment dimensions for type I and type II Continued. D Dash No. C (max) Type I Type II E F G H -04 0.403 0.28 0.28 0.74 0.37 0.56 0.87 -06 0.515 0.29 0.28 0.9

9、5 0.54 0.75 1.06 -08 0.515 0.29 0.100 0.95 0.54 0.75 1.06 -10 0.820 0.40 0.263 1.37 0.76 1.00 1.53 -12 0.820 0.40 0.263 1.37 0.76 1.00 1.53 16 0.905 0.38 0.160 1.62 0.99 1.24 1.77 -20 0.546 0.16 0.110 1.87 1.24 1.50 2.00 -24 0.736 0.23 - 2.12 1.49 1.74 2.25 NOTES: 1. Dimensions are in inches, unless

10、 otherwise specified, tolerances decimals + .010. 2. The surface of shoulder sleeve must fully contact with MIL-DTL-25427/2 bulkhead coupling half male surface when coupled with body nut. 3. MIL-DTL-25427/3 type I hose attaching halves are designed to be used with MIL-DTL-25427/6 type I coupling nut

11、s only and MIL-DTL-25427/3 type II hose attaching halves are designed to be used with MIL-DTL-25427/6 type II coupling nuts only. Type I and type II hose attaching coupling halves or coupling nuts are not interchangeable with each other. However, type I or type II hose attaching half assemblies with

12、 nuts installed are interchangeable with the aircraft bulkhead halves of the same sizes and pressure classes. 4. For design feature purposes, this specification sheet takes precedence over the procurement document. 5. Referenced documents shall be of the issue in effect on date of contract award. RE

13、QUIREMENTS: 1. Material -for material requirements, see procurement specification MIL-DTL-25427. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-25427/3 52. Finish -for finish requirements, see procurement specification MIL-DTL-25427. 3. The

14、surface of the aluminum alloy parts, after anodizing, sealing and surface treatment, shall be free of pits, powder coatings, discontinuities (such as scratches or breaks) and shall be uniform in appearance. 4. External threads shall be produced by die cutting or machining by the single point method.

15、 5. The coupling body shall have wrench flats for wrenching of end fitting connectors. 6. The part or identification number (PIN) consists of the letter M, the specification sheet number, a dash number from table I, material code, end fitting type and pressure class. M 25427/3 -X X X XXXX X Example:

16、 M25427/3-16DV1000 type I represents 1 inch tube hose attaching coupling half, 2024 aluminum,1000 PSI flareless fitting end, type I 7. Marking. Marking shall consist of the complete specification sheet part number and manufacturers name, trademark, or CAGE code and shall be impression stamped or las

17、er etched and shall be protected from corrosion. 8. Interchangeability. Coupling, coupling halves, or coupling parts shall be interchangeable having the same tube size and pressure class. This coupling half configuration is known to be similar to Stratoflex coupling half 13901, Eaton coupling half 1

18、55-S5, and Hydraulic International coupling half HL-A-XF-B. Parker coupling half 4400 has a smaller collar (D Specification sheet number Dash number (see table I herein) Type fitting end U = AS4395 style E flared V = AS4375 style E flareless W = AS85421/1 style 1 beam seal Pressure class 1000=1000 P

19、SI (see 1.2 of MIL-DTL-25427) Material code (see MIL-DTL-25427) M Prefix (M=military) Type I or II (see table I of MIL-DTL-25427) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-25427/3 6diameter) and will not interchange with other coupling

20、halves. Suppliers seeking to be on QPL-25427 are responsible for interchangeability and shall perform the manual operation test to ensure a manufactured coupling is interchangeable with other suppliers couplings and coupling halves and vice versa. 9. Operation. Connection and disconnection of the co

21、upling half with MIL-DTL-25427/2 bulkhead mounting half and MIL-DTL-25427/5 coupling plug shall be easily accomplished using a simple turning motion. The coupling halves when assembled shall function satisfactorily as required in MIL-DTL-25427. When connecting the coupling halves, the coupling assem

22、bly may have a partially coupled and unlocked position, but shall remain stable and permit fluid flow. 10. Test requirements. The test shall be performed in accordance with the applicable test requirements of MIL-DTL-25427. Suppliers seeking qualification of new couplings are responsible for interch

23、angeability of their coupling halves with the existing qualified couplings. The qualifying activity will perform the manual operation tests of the coupling halves provided by manufacturers whenever necessary to ensure interchangeability and leakage within the allowable limit. 11. Intended use. This

24、hose attaching coupling half is intended for use in ground support equipment delivering hydraulic fluid from ground cart to aircraft operating at 3000 and 5000 PSI and returning at 1000 PSI. Type II system fluid is capable of operating at temperature ranging from -65 F to +275 F. These couplings hal

25、ves are intended for use in military and aerospace hydraulic ground support equipment where the bulkhead mounting half and protective cap are part of the aircraft and the hose attaching half and protective plug are part of the ground support equipment. CONCLUDING MATERIAL Custodians: Preparing activ

26、ity: Army-AV Navy-AS Navy-AS Air Force-99 (Project 4730-2008-126) Review activities: Army-AT, MI Navy-SA Air Force-11 DLA-CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-