NAVY MIL-DTL-24231 16 E-2013 CONNECTOR ADAPTER FOR MOLDED PLUG TYPE II SEVEN-CONDUCTOR.pdf

《NAVY MIL-DTL-24231 16 E-2013 CONNECTOR ADAPTER FOR MOLDED PLUG TYPE II SEVEN-CONDUCTOR.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24231 16 E-2013 CONNECTOR ADAPTER FOR MOLDED PLUG TYPE II SEVEN-CONDUCTOR.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/16E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/16D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, ADAPTER, FOR MOLDED PLUG, TYPE II, SEVEN-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for use by al

2、l Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 5. 2. Material for adapter body shall be manufactured

3、 from nickel-copper alloy in accordance with Class A, Form 1, hot-finished condition of QQ-N-281 with a minimum yield strength of 40,000 lbf/in2 at 0.2 percent offset, or nickel-copper alloy in accordance with Class A, Form 1, cold-drawn condition of QQ-N-281 with a minimum yield strength of 50,000

4、lbf/in2 at 0.2 percent offset. 3. All dimensions are in inches. 4. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-2423

5、1/16E(SH) 2 FIGURE 1. Connector, adapter. MOUN TING DIMEN SIO N SMOUN TING BOLT S 12-13NC - 2A378FIGUR E 1 . C onne ctor adapt e r .ASSY, AD APT ER BO D YM24 231/1 6- 04 0GASKET , O-R IN GSAE- AS28 775- 21 3RET AINING RINGM24 231/7- 04 1GASKET, O-R ING (2 R EQD )SAE- AS28 775- 22 0PIN, GUID EFLA N G

6、E, 112“ HIGHI M PACT R I GID PV CM24 231/1 6- 04 0ASSEM BLY, C APM24 231/1 6- 03 0BRA SS SCR EW M24 231/15- 04 3SAFET Y CHA INM24 231/1 5- 04 2ASSEMBLY, ADAPTE R (7 - C ON D )M24 231/1 6- 00 1 SYM. N O. 11 16ASSEMB LY I N SER T ,MOLD ED M 2423 1/16- 02 0NYL ON INSER T X 0. 20 3 LG (2 R EQD )M24 231/

7、5- 07 7CAP , M 24 231/13- 01 1BRASS SCR EWM24 231/1 5- 04 1SPR I N G PINCR ES N ASM17 15 02DR ILL 0.094 HO LEAT A SSEM BL YFOR SPRING PIN60.1 270.1 23431314111101791281572Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/16E(SH) 3 FIGURE

8、2. Assembly, adapter body M24231/16-010. 125ALL OVER E XCE PT A S S H O W N0.0620. 93 7SR 0. 04 60.04632301.1891.1851. 29 70.0270.023301. 20 41.4051.40132FIGURE 2. Assembly, adapte r body - M24231/16 -010 .21.6171.6131832323167320.3440.4370.500 0.120 H O LE S0.187 D E EP . D ONOT P ENE T R A T E+0.

9、00 0-0.0 050.047R G RO O V E0.3440.4370.5007321831632323.438301. 20 40.051 R, P OLA R IZ IN GG RO OV E+0. 00 1-0.0 01132R0.719316332H OLEPIN, W E LD17642.2 50-1 2UN -2 AUNDE R C U T132R0.0642-12UN -2A (B OT H EN D S )0.051 R, P OLA R IZ IN GG RO OV E+0. 00 1-0.0 010.78129322.5322 Provided by IHSNot

10、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/16E(SH) 4 FIGURE 3. Flange M24231/16-040. FIGURE 4. Assembly, cap M24231/16-030. PAD 12 X 14 , NI-A L -B Z180.1 64-3 2NC -2 B14 D EE P65FIG URE 4. As se mbly , ca p - M2 42 31 /16 -03 0 . 17CAPM2423 1/ 13 -0

11、 11FIG UR E 3. Fl ange - M24 231/ 16-0 40 .1116R EF2916R EF78R EF5 .00 R EF1342M2/16-040STAMP OR EN GR A V EAS SH OWN AND FI LLWITH WH ITE E NAME L12FL ANGEM2 423 1/16-04030378916DRILL(4 HOLES)2.250-12 UN-2B0.164-32 NC-2B1 HOLE 12D EEP12 17 Provided by IHSNot for ResaleNo reproduction or networking

12、permitted without license from IHS-,-,-MIL-DTL-24231/16E(SH) 5 FIGURE 5. Assembly, insert, molded M24231/16-020. MO LDED E P OX YRES IN INS E RT0.9670.963132R15161.1 730.2 33 (TY P )0.2 70 (TY P )0.1 35 (TY P )CL0.187382.0001332+132-132WIRE0.053316716PIN CONTACT . EACH P IN S HA LL B ECONNECTE D TO

13、ITS MA T CHI NG P INNO. O N OPPOSITE E ND. ( 14 R E QD)12345671819163FIG URE 5. As se mbly , ins ert , mold ed - M24 23 1/1 6-0 20 .1236754CL0.2 33 (TY P )0.055R GROO V E0.2 70 (TY P )0.1 35 (TY P )MOL D IN P IN N UMBE RSON EACH E ND0.9 173 Provided by IHSNot for ResaleNo reproduction or networking

14、permitted without license from IHS-,-,-MIL-DTL-24231/16E(SH) 6 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/16- 3/ Material/specification Remarks 001 1 Connector, adapter, 7-conductor, symbol no. 1116 1 - See figure 1. 2 Body, adapter 1 Ni-Cu, Class A, QQ-N-281 See figure 2 an

15、d requirement 2. 3 Insert assembly, molded 1 See items 16, 17, and 19. See figure 5. 4 Insert 2 M24231/5-077 See figure 1. 5 Pad, diameter by 1 Ni-Al-BRZ, ASTM B150/B150M See figure 4. 6 Cap, pressure-proof 1 M24231/13-011 4/ See figure 1. 7 Gasket, O-ring 1 SAE-AS28775-213 5/ Lubricate with silicon

16、e compound, SAE-AS8660; see figure 1. 8 Gasket, O-ring 2 SAE-AS28775-220 5/ See item 7. 9 Pin, guide 4 M24231/12-012 See figure 1. 10 Screw, roundhead 1 M24231/15-043 See figure 1. 11 Screw, roundhead 1 M24231/15-041 See figure 1. 12 Flange, 1-inch 1 High impact rigid PVC See figure 3. 13 Chain, saf

17、ety 1 M24231/15-042 6/ See figure 1. 14 Pin, spring 1 CRES, NASM 171502 See figure 1. 15 Ring, retaining 1 M24231/7-041 See figure 1. 16 Pin, contact 14 MIL-DTL-24231 See figure 5. 17 Cap, assembly 1 M24231/13-011, modified as shown 4/ See figure 4. 18 Epoxy resin, molded As required Cast epoxy resi

18、n compound 7/ See figure 5. 19 Wire As required Type B-16, SAE-AS22759/11 See figure 5. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of e

19、ach size. 4/ Cap material shall be Ni-Al-BRZ, ASTM B150/B150M. 5/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. 6/ Safety chains shall be coated with gray plastisol or covered with sleeving in acc

20、ordance with MIL-I-631 (size number 1, 0.294 id, Subform Ua, Grade a, Class II, Category 1, color white) for noise reduction. 7/ Arco Set 200, M.M. Reif and Co., Ivyland, PA, or PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. Provided by IHSNot for ResaleN

21、o reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/16E(SH) 7 CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935

22、-2011-065) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-