NAVY MIL-DTL-22520 41-2008 CRIMPING TOOLS TERMINAL HAND WIRE TERMINATION TYPE II FOR TERMINALS AND SPLICES SIZE 10-14《终端和铰接用尺寸为10-14的II型端接器手动简易压接工具》.pdf

《NAVY MIL-DTL-22520 41-2008 CRIMPING TOOLS TERMINAL HAND WIRE TERMINATION TYPE II FOR TERMINALS AND SPLICES SIZE 10-14《终端和铰接用尺寸为10-14的II型端接器手动简易压接工具》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-22520 41-2008 CRIMPING TOOLS TERMINAL HAND WIRE TERMINATION TYPE II FOR TERMINALS AND SPLICES SIZE 10-14《终端和铰接用尺寸为10-14的II型端接器手动简易压接工具》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5120 INCH-POUND MIL-DTL-22520/41 16 June 2008 DETAIL SPECIFICATION SHEET CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; TYPE II FOR TERMINALS AND SPLICES SIZE 10-14 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements

2、for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-22520. FIGURE 1. Crimp tool configuration.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22520/41 2 FIGURE 1. Crimp tool configuration - Continu

3、ed. FIGURE 2. Wire barrel crimp dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22520/41 3 FIGURE 3. Insulation barrel crimp dimensions. TABLE I. Available gages for tool. Gage part number Gage type Gage area MIL-DTL-22520/42-01 G

4、o/No-Go Wire MIL-DTL-22520/42-02 Go/No-Go Insulation (position #1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22520/41 4 TABLE II. Metric equivalents. Inches MM Inches MM Inches MM Inches MM 0.001 0.025 0.015 0.381 0.283 7.188 2.00 50.80

5、0 0.002 0.051 0.020 0.508 0.284 7.214 3.25 82.550 0.003 0.076 0.031 0.787 0.337 8.560 3.50 88.900 0.005 0.127 0.074 1.880 0.341 8.661 12.20 309.880 0.008 0.203 0.101 2.565 0.342 8.687 17.00 431.800 0.010 0.254 0.127 3.226 0.625 15.875 17.50 449.500 0.129 3.277 0.90 22.860 0.172 4.369 1.15 29.210 0.1

6、88 4.775 NOTES: 1. Dimensions are in inches. 2. Metric equivalents when specified are based upon 1.00 inch = 25.4 millimeters. 3. Unless otherwise specified herein or in MIL-DTL-22520, tolerances are + .010 inch (0.25 millimeters) for three place decimals and + .5 for angles. 4. Refer to MIL-DTL-225

7、20/42 for calibration, inspection gage (M22520/42-01 and -02). REQUIREMENTS: 1. The envelope dimensions of the tool shall be in accordance with figure 1. Outline configuration optional within maximum dimensions shown for closed handle position. 2. The wire barrel crimp gaging dimensions and insulati

8、on barrel crimp gaging dimensions shall be in accordance with figures 2 and 4 when the tool is in the closed handle position. 3. The tool shall not be greater than 2.25 lb (1.02 kg). 4. Material: Jaw - 38 point carbon min. alloy steel Heat Treat Rockwell C 50 55 or equivalent. Handles - Steel or equ

9、ivalent. 5. Finish: Black oxide or equivalent. 6. Cycle control (ratchet) adjustment device shall be set to release between 75 to 85 pounds and shall be tamper proof. 7. Convex crimp surfaces shall be polished to 48 (RMS) Microfinish minimum. 8. Each tool shall have an instruction sheet which includ

10、es applications, usage and instructions. 9. Tool part number: M22520/41-01 10. Complete manufacturers name or AIR 1351 listed logo shall be permanently marked on the tool. 11. The tool shall have three (3) adjustment settings to regulate insulation crimp height. 12. Qualification testing shall be in

11、 accordance with MIL-DTL-22520 type 2 tool requirements. Initial qualification test samples shall consist of a sample lot of terminals and/or splices from all Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22520/41 5 sources (brands) qualifi

12、ed at the time of tool testing, and the tool is required to meet the minimum requirements with all samples tested. 13. Locator (positioner) design optional providing it meets the performance requirements of all terminals/splices used with the tool. 14. Optional design shall have the same marking req

13、uirements as shown on figure 3. 15. No loose parts or components that can become Foreign Object Damage (FOD) hazards are permitted. APPLICATION: The crimp cavities are for the crimping of SAE AS25036, SAE AS17143, terminal and splices in sizes 12 - 10. CONCLUDING MATERIAL Custodians: Preparing activ

14、ity: Navy - AS Navy - AS Army - CR (Project 5120-2007-002) AF - 11 Review activities: Navy - EC, MC, OS, SH DLA - CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-