NAVY MIL-C-87059 A-1989 CLOTH KNITTED NYLON TRICOT《尼龙经编织物编织布》.pdf

《NAVY MIL-C-87059 A-1989 CLOTH KNITTED NYLON TRICOT《尼龙经编织物编织布》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-87059 A-1989 CLOTH KNITTED NYLON TRICOT《尼龙经编织物编织布》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND 1 MIL-C-87059A(NU) 6 Februarv 1989 SUPERSEDING MIL-C-87059(SA) 30 October 1978 MILITARY SPECIFICATION CLOTHt KNITTED, NYLON, TRICOT *This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by. all Departme

2、nts and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope. This specification covers the requirements for a nylon tricot cloth. 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a

3、part of this specification to the extent specified herein, Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. h SPECIFICATIONS FEDE

4、RAL PPP-P-1133 - Packaging of Synthetic Fiber Fabrics Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use .in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick,

5、 MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. -?AMSC NIA FSC 8305 *DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. THIS DOCUMENT CONTAINS 4 PAGES. Provided

6、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- _ - flIL-C-87059A 3 9999906 04LObL3 b M . - - MIL-C-87059A(NU) STANDARDS FEDERAL FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-1491 Attribu

7、tes - Glossary of Knitting Imperfections (Copies of specifications, standards, drawings, and publications required by contractors in cbnnection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. ) * 2.1.2 Other Government doc

8、uments, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. LAWS AND REGULATIONS a Rules and

9、 Regulations Under the Textile Fiber Products Identification Act (Application or copies should be addressed to the Federal Trade Commission, Washington, DC 20580.) * 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise s

10、pecified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of t

11、he solicitation. TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (Application for copies should be addressed to the AATCC National Headquarters, P.O. Box 12215, Research Triangle Park, NC 27709-9989.) AMERICAN SOCIETY FOR TESTING MATERIALS No. D 3781-80a - Bursting Str

12、ength of Knitted Goods - Constant-Rate-of-Traverse (CRT) Ball Burst Test (Application for copies should be addressed to the American Society for Testing Materials, 1916 Race St., Philadelphia, PA 19103-1187.) (Technical society and technical association documents are generally available for referenc

13、e from libraries. They are also distributed among technical groups and using Federal agencies.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.3 Order of precedence. In the event of a conflict between the text of this specification and the refer

14、ences cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Standard sample. The finished cloth shall match-the standard and shal

15、l be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3). The standard sample is identified under piece number 79033. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article ins

16、pection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Fiber. The fiber shall be regular tenacity, dull luster, (front guide bar) and regular tenacity, mid-dull luster (back guide bar) nylon. Testing shall be as specified in 4.5. The yarn for the front guide bar shall be round cross section, no

17、minal 30 denier, 10 filaments with built-in anti-static protection. The yarn for the back guide bar shall be tri-loba1 cross section, nominal 40 denier, 13 filaments with built-in anti-static protection. Testing shall be as specified in 4.5. 3.4 Physical requirements. The finished cloth shall confor

18、m to the physical requirements shown in Table I when tested as specified in 4.5. 3.3.2 - Yarn. TABLE I. Physical requirements Characteristics Minimum Maximum Weight, oz/yd2 (g/m2) Wales/inch (2.54 cm) Courses/inch (2.54 cm) Bursting strength, lbs (N) 2.7 (91.5) - 32 (32) - 68 (68) - 100 (445) - 3.4.

19、1 Knit. The cloth shall be knitted on a single needle bed warp knit machine having 31 needles per inch (12.2 per cm) minimum and two guide bars. Testing shall be as specified in 4.3. 3.4.2 Knit pattern. The guide bar stitch pattern shall be as follows when tested as specified in 4.5: Front Bar WO, 0

20、/1 Back Bar 1/0, 4/5 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-87059A(NU) 3.4.3 Width. Unless otherwise specified (see 6.2), the width of the finished cm shall be a minimum of 50 inches (127.0 cm) inclusive of selvages. 3.5 Color. The c

21、olor shall be white, shade 3006 and shall match the standard sample. * 3.5.1 Matchin . The finished cloth shall match the standard sample when viewed un d er f ltered tungsten lamps which approximate artificial daylight having a correlated color temperature of 7500 + 200 K, with illumination of 100

22、+ 20 foot candles, and shall be a good mat t an 4.5 nor more than 7.0 when tested as specified in 4.5. 3.10 Face identification. The face side of the cloth shall be identified by stamping on that side with the word llFacell at each end of the roll. 3.11 Length and put-up. Unless otherwise specified

23、(see 6.2), the finished cloth shall be furnished in continuous lengths, each not less than 40 yards (36.4 m). Each length shall be put-up on full width rolls as specified in PPP-P-1133. 3.12 Fiber identification. Each piece shall be labeled, or ticketed for fiber coxtent in accrdance with the Rules

24、and Regulations Under the Textile Fiber Products Identification Act. 3.13 Workmanshi The finished cloth shall conform to the quality The. occurrence of defects shall not exceed the establishe d y t s document. applicable quality level specified. 4 Provided by IHSNot for ResaleNo reproduction or netw

25、orking permitted without license from IHS-,-,-4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. . Except as otherwise specified in the co

26、ntract or order, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspec

27、tions are deemed necessary to assure supplies and services conform to prescribed requirements. O * 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection s

28、ystem or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conf

29、ormance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of compliance are submitted, the Government. reserves the right to check test such

30、 items to determine the validity of the certification. 4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: O 1. First article inspection (see 4.3). 2. Quality conformance inspection (Se 4.4). 4.3 First article inspection. When required (see 3.2 a

31、nd 6.2), the first article shall be visually examined for appearance, color and finish, and shall be tested for physical and chemical properties in accordance with methods specified in 4.5. 4.4 Quality conformance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105,

32、 except where otherwise indicated. 4.4.1 Component and material inspection. In accordance with 4.1 above, components and materials shall b e tested in accordance with all the - requirements of referenced specifications, drawings, and standards unless otherwise“excluded, amended, modified, or qualifi

33、ed in this specification or applicable procurement documents. 4.4.2 Examination of the end item. Examination of the end item shall be in accordance with 4.4.2.1 through 4.4.2.3. 5 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_-. - - I - MIL-C-87

34、054A 83 W 7777706 0430637 3 MIL-C-87059A(NU) 4.4.2.1 Yard-by-yard examination. The required yardage of each roll in the sample shall be examined on the face side and visual defects as defined in MIL-STD-1491 shall be classified as listed. All defects found shall be counted regardless of their proxim

35、ity to each other, except where two or more defects represent a single local condition of the cloth, in which case only the more serious defect shall be counted. A continuous defect shall be counted as one defect for each wale-wise (lengthwise) yard (0.91m) r fraction thereof in which it occurs. The

36、 sample unit for this examination shall be one linear yard (0.9lm). The acceptable quality levels for this examination shall be 2.5 major defects and 6.5 total defects (major and minor combined) per 100 units (yards) (91.4m). The sample size shall be based upon inspection level II of MIL-STD-105. Th

37、e lot size shall be expressed in units of one yard (0.91m). The number of rolls from which the sample is to be selected shall be in accordance with Table II. An approximately equal number of yards (meters) shall be examined from each roll in the sample. Classification Defect Major Minor Any hole, cu

38、t, tear, run X Dropped stitch, end out X Tuck stitch, pulled stitch or needle streak X Mend (any) X Coarse or. fine yarn i/ Foreign matter 1/ X Knot oversize, extending above the surface of cloth Kink or untrimmed end X Crease or wrinkle, embedded X Stretch (stitch tension) knitting tension too tigh

39、t Shade bar 1/ X X X or too loose X Spot or stain X Barre marks, broken yarns or dye stains-1/ - X - 1/ Clearly visible at normal inspection distance (approximately 3 feet (0.9lm). 4.4.2.2 Overall examination. Each defect shall be counted no more than once in each roll examined. The sample unit shal

40、l be one roll. The sample size (number of rolls selected as sample) and the number of defects acceptable shall be as shown in Table II. Defects -de of cloth not on inside Width less than specified Overall uncleanness Uneven knitting throughout the piece Off shade, shaded end to end, side to side, si

41、de to center, or throughout the Poor dye penetration, mottled, streaky or cloudy Cut edge is not paralled to wales in the finished cloth Not labeled in accordance with the Textile Fiber Products Identification Act Face marking missing from either or both ends of the roll Face marking on the wrong si

42、de Hand and finish not equal to standard roll 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Table II - Sample sizes SamDle size AcceDtance Lot size (yards) (0.91m) (Eolls) number up to 1200 1/ 1201 up to and including 3200 3201 up to and includin

43、g 10,000 10,001 up to and including 35,000 35,001 up to and including 150,000 150,001 and over 3 O 5 O 8 O 13 O 20 1 32 2 - 1/ if a lot contains fewer than three rolls, each roll in the lot shall be examined. 4.4.2.3 Examination for length. 4.4.2.3.1 Individual rolls. During the yard by yard examina

44、tion, each roll in the sample shall be examined for length. Any length found to be less than the minimum specified, or more than two yards less than the length marked on the ticket shall be considered a defect with respect to length. The sample unit shall be one roll. The sample size (number of roll

45、s selected as sample) and the acceptance number shall be as shown in Table II. 4.4.2.3.2 Total yardage in sample. The lot shall be unacceptable if the total of the actual length of rolls in the sample is less than the total of the lengths marked on the ticket. The rolls examined shall be those selec

46、ted for the examination of individual rolls. 4.4.3 Examination of packaging requirements. An examination shall be made in accordance with the provisions of PPP-P-1133 to determine that preservation, packaging, packing, and marking comply with section 5 requirements. * 4.5 Testing of the end item. Th

47、e methods of testing specified in FED-STD-191, wherever applicable, and as listed in Table IV shall be followed. The physical and chemical values specified in Section 3 apply to the average of the determinations made on a sample unit for test purposes as specified in the applicable test methods. The

48、 sample unit shall be 2 1/2 yards (2.3m) full width of the finished cloth. The sample size shall be as listed in Table III. The lot size shall be expressed in units of 1 yard (0.91m). The lot shall be unacceptable if one or more sample units fail to meet any requirement specified. All test reports s

49、hall contain the individual values utilized in expressing the final results. Table III - Sample size Lot size (yards) 800 or less 2 801 up to and including 22,000 3 22,001 and over 5 Sample size (units) e 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y z MIL-C-87059A(N) Table IV - Test Methods Requirement Test Characteristic Paragraph Met hod Fiber identification Yarn denier