NAVY MIL-C-87052 B-1990 CLOTH TWILL POLYESTER WHITE《白色涤纶斜纹织布》.pdf

《NAVY MIL-C-87052 B-1990 CLOTH TWILL POLYESTER WHITE《白色涤纶斜纹织布》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-87052 B-1990 CLOTH TWILL POLYESTER WHITE《白色涤纶斜纹织布》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-C-87052B 83 m 9777706 0429786 O m MIL-C-87052B 14 May 1990 SUPERSEDING MIL-C-87052A 13 September 1983 MILITARY SPEC1 FI CATI ON CLOTH, TWILL, POLYESTER, WHITE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specificat

2、ion covers the requirements for one type of twill cloth made from 100% texturized polyester. 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards and handbooks form a part of this document to the extent specified

3、herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) an

4、d any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the sel-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at t

5、he end of this document or by letter. AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMIL-C-87052B SPECIFICATIONS FEDERAL * PPP-P-1133 - Packaging of Synthetic Fiber Fabrics STANDARDS FEDERAL FED-STD-4 FED-S

6、TD-191 - Textile Test Methods - Glossary of Fabric Imperfections MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes * MIL-STD-2073-1 - DoD Materials Procedures Development and Application * MIL-STD-2073-2 of Packaging Requirements - Packaging Requirement Codes * (Unle

7、ss otherwise indicated, copies of federal and military specification, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) * 2.1.2 Other Government documents, drawings, and publications. The following other

8、Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. Rules and Regulations Under the Textile Fiber Products Identification Act (Copies may be obtained without charge f

9、rom the Federal Trade Commission, Washington, DC 20580). * 2.2 Non-Government publications. The following document(s) form a part of this specification to the extent specified herein. . Unless otherwise specified, the issue of documents which are DoD adopted shall be those listed in the issue of the

10、 DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS AATCC 61-1989 Colorfastness to Launderin

11、g, Home and Commercial: Accelerated AATCC 130-1981 Soil Release: Oily Stain Release Method (Application of copies should be addressed to AATCC National Headquarters, P.O. Box 12215, Research Triangle Park, NC 27709-2215.) 2 Licensed by Information Handling ServicesMIL-C-87052B 83 H 777970b 0929788 4

12、 H MIL-C-87052B (Non-government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) * 2.3 Order of precedence. In the event of a confli

13、ct between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Standard sample. The finished cloth sha

14、ll match the standard and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.4). The standard sample is identified under piece number 89233. Variations from this specification may appear in the sample in which c

15、ase this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample 3 3 Material. unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3.1 Fiber. The fiber shall be polyethylene glycol terephthalate, regular 3.3.2 Yarn. The yarn used in both

16、the warp and filling shall be made by plying two ends of 150 denier octalobal cross section, 33 (+ 3) filaments per end polyester and shall be texturized by the false twist process. All yarns shall contain the same number of filaments (see 4.4.1). 3.4 Color. Unless otherwise Specified the color of t

17、he finished cloth shall be white 3006 and shall match the standard sample. The white cloth shall be fully bleached and supplemented with a blue violet fluorescing optical brightener. All cloth within any one contract shall be processed for whiteness in the same manner. tenacity, semi-dull (see 4.4.1

18、). * 3.4.1 Matching. The color and appearance of the dyed and finished cloth shall match the standard sample when viewed under filtered tungsten lamps approximate artificial daylight having a correlated color temperature of 7500 (+ 200) K, with illumination of 100 (+ 20) foot candles and shall be a

19、good match to the standard sample under incandescent lamplight at 2300 (+ - 200) K. * 3.4.2 Discoloration. The finished cloth shall show fastness to light, laundering, combined laundering and bleaching, wet-dry cleaning and perspiration equal to or better than the standard sample. When no standard s

20、ample is available, the finished cloth shall show a minimum of fgoodff fastness to combined laundering and bleaching, light, laundering, wet-dry cleaning and perspiration. Testing shall be as specified in 4.5. 3.5 Physical Requirements. The finished cloth shall conform to the requirements specified

21、in Table I when tested as specified in 4.5. 3 Licensed by Information Handling ServicesMIL-C-87052B 83 W 7777906 0427787 b W MIL-C-87052B Table I - Physical Requirements Characteristic Requirements Weight oz/sq yd Wm) Yarns per inch (2.5cm) - minimum Warp Fi 11 ing 6.7 (+ 0.5) (227.T + 17) 67 57 Bre

22、aking Strength lbs (N) (min) Warp 200( 890) Filling 150( 668) Tearing Strength lbs (N) (min) 12 (53) Filling 12 (53) Warp 3.5.1 Weave. The weave shall be a 2 right hand twill. i * 3.5.2 Width. Unless otherwise specified (see 6.2) the width of the cloth shall be theminimum of 60 inches (2.5m) inclusi

23、ve of selvages, when fly shuttle looms or shuttless with tuck-in selvage looms are used. For all other shuttleless looms the width measurement shall be made between the last yarn on each side excluding the protruding fringe. * 3.6 Finish, The cloth shall be scoured, heat set, dyed and given an appro

24、ved soil release finish (see 6.5 and when tested as specified in 4.5). Percent add-on of the soil release finish shall be in accordance with the manufacturers instructions. The character of the finished cloth shall be equal to that of the standard sample, 3.7 Non-fibrous materi-als. The starch and p

25、rotein content including chloroform-soluble and water-soluble material of the cloth shall not exceed 3.0 percent when tested as specified in 4.5. * 3.8 Dimensional stability. The finished cloth shall not shrink or elongate more than 3.0 percent in warp and 2.0 in the filling when tested as specified

26、 in 4.5. 3.9 pH. The pH value of the water extract, of the finished cloth shall be no less than 5.0 nor more than 8.5 when tested as specified in 4.5. 3.10 Length and put-up. Unless otherwise specified (see 6.2), the finished . cloth shall be furqished in continuous lengths each not less than 40 yar

27、ds (36.6111). Each length shall be put-up on rolls as specified in PPP-P-1133. 3.11 Fiber identification. Each roll shall be labeled or ticketed for fiber content in accordance with the Textile Fiber Products Identification Act. 4 Licensed by Information Handling ServicesMIL-C-87052B 3 m 777770b 042

28、7770 2 m MIL-C-87052B 3.12 Face identification. The face side of the cloth shall be identified by stamping on that side with the word l1FaceI1 at each end of the roll, 3.13 Workmanship. The finished cloth shall conform to the quality establJshed by this specification. The demerit points per 100 squa

29、re yards (83.6111 ) when calculated as specified in section 4 shall not exceed the established maximum point value. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of al

30、l inspection requirements (examinations and tests) as specified herein, Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Governme

31、nt. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. * 4.1.1 Responsibility for compliance. All items must meet all requirements of sectio

32、ns 3 and 5, The inspection set forth in this mecification shall become a part of the contrators overall inspection System or quality program. The absence of any inspection requirements in the specification- shall not relieve the contractor of the responsibility of ensuring that all products or suppl

33、ies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indi

34、cated or actual, nor does it commit the government to acceptance of defective material. 4.1.2 Certificate of Compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Classification of in

35、spection. The inspection requirements specified herein are classified as follows: 1. First.article inspection (see 4.3). 2. Quality conformance inspection (see 4.4). * 4.3 First article inspection. When required, the Eirst article submitted in accordance with 3.2, shall be inspected as specified in

36、4.4,2 for compliance with design, construction, workmanship, appearance and dimensiohal requirements and tested in accordance with paragraph 4.5 and Table II, 4.4 Quality conformance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105, except where otherwise indicat

37、ed. 5 Licensed by Information Handling ServicesMIL-C-870528 83 = 7799706 0429773 4 MIL-C-87052B 4.4.1 Component and material inspection. In accordance with 4.1 above, components and materials shall be tested in accordance with all the requirements of referenced specifications, drawings, and standard

38、s unless otherwise excluded, amended, modified, or qualified in this specification or applicable procurement documents. In addition, a certificate of compliance shall be submitted for the material requirements of 3.3.1 and 3.3.2. 4.4.2 Examination of the end item. Examination of the end item shall b

39、e in accordance with 4.4.2.1 through 4.4.2.5. 4.4.2.1 Yard-by-yard examination. Each roll in the sample shall be examined on face side only. When the total yardage in the roll does not exceed 100 yards (91.4m), the entire yardage in the roll shall be examined. When the total yardage in the roll exce

40、eds 100 yards (91.4111) only 100 yards (91.4111) shall be examined. All defects as defined in Section III of FED-STD-4, which are clearly noticeable at normal inspection distance (3 feet) (0.91m) shall be scored and assigned demerit points as listed in 4.4.2.1.1, except that only those knots which e

41、xceed the limits shown on Sears Fabric. Defect Scale (see 6.4), “C“ knots shall be scored. No linear yard (increments of 1 yard (0.91m) on the measuring device of the inspection machine) from any one roll within the sample shall be penalized more than 4 points. The sample size shall be 20 rolls sele

42、cted from 20 containprs. The lot shall be unacceptable if the points per 100 square yards (83.6111 ), of the total yardage examined exceeds 25 pointsi The lot shall be unacceptable if the point per 100 square yards (83.6m ) of two or more individual rolls exceeds 238 points. If one roll exceeds the

43、point level per 100 square yards (83.6111 ) a second sample of 20 rolls shall be examined only for individual roll quality examination. The lot shall be unacceptable if one or mo;e rolls in the second sample exceeds 38 points per 100 square yards (83.6111 ). Point computation for lot quality and ind

44、ividual roll quality shall be as follows: Total points scored in sample x 3600 = Points/100 Contracted width of cloth (inches) x total yards inspected square-yds * 4.4.2.1.1 Demerit points. Demerit points shall be assigned as follows: For defects 3 inches (7.6cm) or less 5n any direction one point F

45、or defects exceeding 3 inches (7.6cm), but not exceeding 6 inches (15.2cm) in any direction - two points For defects exceeding 6 inches (15.2cm), but not exceeding 9 inches (22.9cm) in any direction - three points For defects exceeding 9 inches (22.9cm) in any direction - four points The following d

46、efects, when present, shall be scored 4 points for each yard (0.91m) in which they occur: Baggy, ridgy or wavy cloth Width less than specified Characteristics of finish, hand and shade not equal to the standard sample Non uniformity of shade (mottled, streaky or cloudy) Holes, cuts, tears, open plac

47、es 6 Licensed by Information Handling ServicesMIL-C-87052B 3 9999906 0429792 b W MIL-C-87052B 4.4.2.2 Examination of length. 4.4.2.2.1 Individual rolls. During the yard-by-yard examination, each roll in the sample shall be examined for length. Any length found to be less than the minimum specified o

48、r more than 2 yards (1.82111) less than the length marked on ticket shall be considered a defect with respect to length. The lot shall be unacceptable if two or more rolls in the sample are defective with respect to length. 4.4.2.2.2 Total yardage in sample. The lot shall be unacceptable if the tota

49、l of the actual lengths of rolls in the sample is less than the total of the lengths marked on the tickets. The rolls examined shall be those selected for the examination of individual rolls. 4.4.2.3 Examination for shade variation. During the yard-by-yard examination, each roll in the sample shall be examined for shade variation. Any role in the sample exhibiting uneven shade, shade variation side to side, side to center, or end to end, shall be cause for rejection of the entire lot represented by the sample. 4.4.2.4 Examination for shade match and finish, individual rolls. Each roll