NAVY MIL-C-48569 (2)-1978 CATAPULT AIRCRAFT EJECTION SEAT CKU-7 A METAL PARTS ASSEMBLY《航空器座椅弹射器CKU-7 A型金属部件组件》.pdf

《NAVY MIL-C-48569 (2)-1978 CATAPULT AIRCRAFT EJECTION SEAT CKU-7 A METAL PARTS ASSEMBLY《航空器座椅弹射器CKU-7 A型金属部件组件》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-48569 (2)-1978 CATAPULT AIRCRAFT EJECTION SEAT CKU-7 A METAL PARTS ASSEMBLY《航空器座椅弹射器CKU-7 A型金属部件组件》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、* * * * * * * MIGC-48569(OS) .AnlENDr-,m 2 6 February 1978 SUPERWING MIGC-48569(OL;) Amm 1 10 January 1978 MILITARY SPECIFICATION CATAPUET, AIRCRAFT l?JECIION SEAT: W-7/A hrnALI Pm ASrnlBLY This amendment fom a part of Military Specification hlIGC-48569(OS) dated 10 October 1977. PAGE 16 TABL;E IV,

2、“Release, Drawing D10551416“, Major defect 101 : Delete “Concentricity of flange with end“ and substitute “True position of flange with end.“ PACE 21 TABL;E IV: Add “119 Position of scribe mrk Gage/Visual.“ PAm 22 TAm IV: Add “245 Dupth of scribe mark Gage/Visual. It PAGE 23 TAl3U IV, Major defect c

3、lassification 105: substitute “Concentricity of outside diameter (groove end) with outside diameter (thread end). TAi3E IV, Major defects classifications 106, 111, 119 and 122 and Minor defect classification 205: Delete description and Delete tlgroovel and substitute “grooves TBLE IV, Minor defect c

4、lassification 209: Delete “,small OD“ and substitute “OD (groove end). PAGE 24 TABLE IV: “219“ and “220“, respectively, and insert the following : Change present defect classifications “217“ and “218“ to “217 Positions of O-ring grooves from end of tube Gage 218 kngth of &ring land Gage i1 II A Prov

5、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-!i8569 (2) 13 999770b 0321725 T U * * PACE 25 Delete page 25 in its entirety and substitute new page 25 attached. PAGE 26 TABU3 IV: Add defect Classifications “124 Position of scribe nark Gage/Visual

6、215 Drpth of scribe mrk Gage “ PAGE 27 TABU3 IV: Add the following * Washer, Drawing Cl1820367 BITICAL None defined IAJOR 101 102 IINOR Diameter, outer Protective finish All other characteristics Gage Visual Visual /Gage The margins of this amenchnt are marked with an asterisk to indicate where chan

7、ges (additions, mdificaticns, corrections, deletions) from the previous amendment were made. only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendrent. This was done as a convenience custodian : Navy - OS o Preparing Activity: Navy - OS Project No. 1377-N654 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-