NAVY MIL-C-24933-1987 CLOTH FLANNEL COTTON (FLAME RETARDANT TREATED)《法兰绒棉布(阻燃剂处理过)》.pdf

《NAVY MIL-C-24933-1987 CLOTH FLANNEL COTTON (FLAME RETARDANT TREATED)《法兰绒棉布(阻燃剂处理过)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-24933-1987 CLOTH FLANNEL COTTON (FLAME RETARDANT TREATED)《法兰绒棉布(阻燃剂处理过)》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-ZLI933 83 9 77999Ob 038q823 b 33-0 7 MIL-C-24933 23 June 1987 MILITARY SPEC IF ICATION CLOTH, FLANNEL, COTTON (FLAME RETARDANT TREATED) This specificat.ion is approved for use by all Departments and Agencies of the Department of Defense. 6- 1. SCOPE 1.1 Scope. This specification covers the req

2、uirements for one type of ?4 flannel cotton cloth which has been treated with a flame retardant finish. 2 APPLICABLE DOCUMENTS 2.1 Government documents. 2. I. 1 Specifications, standards and handbooks. The following specifications, standards, and handbooks form a part of this specification to the ex

3、tent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISC) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL PPP-P -1 13 4 - Packaging, Packing

4、 of Cotton and Cotton Synthetic Fiber Blend Fabrics (excluding duck fabrics) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 St

5、rathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or bv letter. AMSC NIA FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. THIS DOCUMENT CONTAINS

6、 7 PAGES, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-24733 83 9 777970b 0384824 8 W MIL-C-249 33 MILITARY MIL-T-43548 - Thread, Polyester, Core: Cotton-, Rayon-, or Pol yes t er Cove red STANDARDS FEDERAL FED-S TD-19 1 - Textile Test Metho

7、ds FED -S TD- 4 - Glossary of Fabric Imperfections MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspections by At tributes (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from t

8、he procuring activity or as directed by the contracting officer .) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issu

9、es shall be those in effect on the date of the solicitation. LAWS AND REGULATIONS Rules and Regulations Under the Textile Fiber Products Identification Act (Copies may be obtained from the Federal Trade Commission, Washington, DC 20580). 2.2 Order of precedence. In the event of a conflict between th

10、e text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified

11、 (see 4.3 and 6.2), the contractor shall furnish a sample for first article inspection and approval. 3.2 Material. 3.2.1 Yarn. The yarn shall be made from cotton which has been carded, drawn, and spun into singles yarn for both the warp and the filling, when tested as specified in 4.5. 2 A a Provide

12、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2493 3 3.3 Weave. The weave shall be a 3 or 4 harness twill, when tested as specified in 4.5. 3.4 Color. The cloth shall be unbleached. 3.5 Physical requirements. The finished cloth shall conform to the

13、physical requirements shown in TabJe I when tested as Specified in 4-50 TABLE I. Physical requirements Characteristics Minimum Maximum 2 2 Weight, oz/yd (gm/m ) Greige Finished Warp Fil 1 i ng Stiffness, in-lbs (N.m) Warp Filling n Tear Strength, lbs (N) 3 2 Air permeability, ft3/min, (cm /sec/cm Ya

14、rns per inch (2.54 cm) Warp Filling Warp Filling Initially and after 25 launderings: Breaking strength, lbs. (N) Flame resistance After flame time, seconds After glow time, seconds Char length. inches (2.54 cm) 8.00 (271.2) - 8.75 (296.6) 9.75 (330.5) 5.00 (22.2) - 4.50 (20.0) - - .O06 (.0007) - .O0

15、4 (aO004) 20 (10.2) - 62 38 65 (289.2) - 40 (178.0) - 2 5 5 - - - VI 3.6 Finish. The cloth shall be napped on the back side, scoured, desized, and given an approved flame retardant treatment (see 6.4 and 6.5). 3.6.1. Toxicity approval. Only those flame retardant treatments already evaluated and appr

16、oved by the appropriate medical service in regards to toxicity and solicited in the invitation for bids or requests for proposals shall be considered acceptable for the related procurement (see 6.4). 3.7 Nonfibrous material. Prior to the application of the flame retardant treatment, the cloth shall

17、contain no more than 3.0 percent starch and protein content including chloroform-soluble and water-soluble material, when tested as specified in 4.5. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-24733 83 W 9979906 03L182b L MIL-(2-24933 3.

18、8 Width. The width of the cloth shall be as specified (see 6.2) and shall be the minimum acceptable width, inclusive of selvages when fly shuttle looms or shuttleless with tuck-in selvage looms are used. For all other shuttleless looms the width measurement shall be made between the last warp yarn o

19、n each side excluding the protruding fringe. 3.9 Seam efficiency. The cloth shall have a seam efficiency of not less than 85 percent when tested as specified in 4.5. 3.10 Dimensional stability. The finished cloth shall not shrink nor elongate more than 2.0 percent in either the warp or filling direc

20、tion when tested as specified in 4.5. The preshrinking process used shall not be identified by name or by trademark, either on the cloth, ticket, or package. rn 3.11 pH, The pR value of the wafer extract of the finished cloth shall be - no less than 5.0 nor more than 8.5 when tested as specified in

21、4.5. A 3.12 Length and put-up. Unless otherwise specified (see 6.2), the cloth shall be furnished in continuous lengths, each not less than 40 yards. Each length shall be put up in full width rolls as specified in 5.1. 3.13 Fiber identification. Each piece shall be labeled, or ticketed for fiber con

22、tent in accordance with the Textile Fiber Products Identification Act. 3.14 Face identification. The face side of the cloth shall be identified by stamping on that side with the word “Face“ at each end of the roll. 3.15 Workmanship. The cloth shall conform to the quality and grade of product establi

23、shed by this document. The occurence of defects shall not exceed the applicable quality levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified

24、 herein. Except as otherwise specified in the contract or order, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections

25、set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a

26、part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requiremen

27、ts of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

28、m IHS-,-,-I I l l I I I c I f I MIL-C-2Y733 83 m 777770b 0384827 3 m MIL-C-24933 4.1.2 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Classification of inspectio

29、n. The inspection requirements specified herein are classified as follows: 1. First article inspection (see 4.3). 2. Quality conformance inspection (see 4.4). 4.3 First article inspection. When required (see 3.1 and 6.2), the first article shall be visually examined for appearance, color, and finish

30、, and shall be tested for physical and chemical properties in accordance with the methods specified in 4.5. 4.4 Quality conformance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105, except where otherwise indicated. 4.4.1 Component and material inspection. In acc

31、ordance with 4.1 above, components and materials shall be tested in accordance with all the requirements of referenced specifications, drawings, and standards unless otherwise excluded, amended, modified, or qualified in this specification or applicable procurement documents. 4.4.2 Examination of th

32、e end item. Examination of the end item shall be in accordance with 4.4.2.1 through 4.4.2.3. 4.4.2.1 Yard-by-yard examination. Each roll in the sample shall be examined on the napped side only. When the total yardage in the roll does not exceed 100 yards (91.4m) the entire yardage in the roll shall

33、be examined. When the total yardage in the roll exceeds 100 yards (91.4m), only 100 yards (91.4m) shall be examined. Ail defects as defined in Section 1 of FED-STD-4, which are clearly noticeable at normal inspection distance (3 feet) (0.9m) shall be scored and assigned demerit points as listed in 4

34、.4.2.1.1, except that only the slubs and knots which exceed the limits shown on Sears Fabric Defect Scale (see 6.3), “D“ for slubs, or 3-1/2 as applicable, and “C“ for knots shall be scored. No linear yard (increments of 1 yard (0.91m) on the measuring device of the inspection machine) from any one

35、roll within the sample shall be penalized more than 4 points. The sample size shall be in accordance with the following: Lot size (yards) Sample size (rolls) - i/ 3200 or less 3201 thru 10,000 10,001 and over 8 13 20 i/ Only one roll shall be taken from any shipping container, unless the number of s

36、hipping containers in the lot are less than the number of rolls required for sampling, in which case, all shipping containers shall be sampled. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ - MIL-C-24933 83 W 999990b 0384828 5 W MIL-C-249 33 2

37、The lot shall be unacceptable if the points per 100 square yards (83.6m ) of the total yardage examined exceeds 28 points. The lot sh 11 be unacceptable if the individual points per 100 square yards (83.6m ) of two or more individual rolls exceed9 40 points. If one roll exceeds the point level per 1

38、00 square yards (83.6m ), a second sample, the same size as the final sample, shall be examined only for individual roll quality examination. The lot shall be unacceptable if one or mor5 rolls in the second sample exceeds 38 points per 100 square yards (83.6m ). Point computation for lot quality and

39、 individua1,roll quality shall be as follows: 13 Total points scored in sample X 3600 = Points per 100 Contracted width of cloth (inches) x total yards inspected square y rds 4 (83.6m ) 4.4.2.1.1 Demerit points. Demerit points shall be assigned as follows: For defects up to and including 3 inches (7

40、.6cm) For defects exceeding 3 inches (7.6cm) but not For defects exceeding 6 inches (15.2cm) but not For defects exceeding 9 inches (22.8cm) in any in any dimension = one point exceeding 6 inches (15.2cm) in any dimension = two points exceeding 9 inches (22.8cm) in any dimension = three points dimen

41、sion = four points The following defects, when present, shall be scored 4 points for each yard (0.91m) in which they occur: Baggy, ridgy, or wavy cloth Width less than specified Excess ive neppi nes s Object ionable odor 4.4.2.2 Examination for length. 4.4.2.2.1 Individual rolls. During the yard-by-

42、yard examination, each roll in the sample shall be examined for length. Any length found to be less than the minimum specified or more than two yards (1.8m) less than the length marked on the ticket shall be considered a defect with respect to length. The lot shall be unacceptable if two or more rol

43、ls in the sample are defective in respect to length. 4.4.2.2.2 Total yardage in sample. The lot shall be unacceptable if the total of the actual lengths of rolls in the sample is less than the total of the lengths marked on the tickets. The rolls examined shall be those selected for the examination

44、of individual rolls. I J 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2Y733 83 9777906 0384827 7 H I l l 1 I I I I I I I I i MIL-C-24933 4.4.2.3 Examination for face identification, non-identification of preshrinking process , and complian

45、ce with Textile Fiber Products Identification Act. Durine: the vard-bv-vard examination. each roll in the u .r.r sample shall be examined. for defects listed below. The lot shall be unacceptable if two or more of the following defects are present in the sample: Face identification missing from eithe

46、r or both ends Face identification on wrong side Preshrinkage process identified by name or trademark on cloth, ticket, Not labeled or ticketed in accordance with the Rules and Regulations under or package the Textile Fiber Products Identification Act 4.4.3 Examination of packaging requirements. An

47、examination shall be made in accordance with the provisions of PPP-P-1134 to determine whether packaging, packing, and marking comply with section 5 requirements. 4.5 Tests. The methods of testing specified in FED-STD-191, wherever applicable, and as listed in Table 11 shall be followed. The physica

48、l and chemical values specified in section 3 apply to the results of the determinations made on a sample unit for test purposes as specified in the applicable test method. The sample unit shall be 5 continuous yards (4*6m) full width of finished cloth, and 1/4 yard (.23m) full width of cloth prior t

49、o the application of the finish for determination of nonfibrous materials and greige weight. The lot size shall be expressed in units of 1 yard (0.9m) each. The lot shall be unacceptable if one or more sample units fail to meet any test requirements specified. Ai1 test reports shall contain the individual values utilized in expressing the final results. The sample size shall be as shown in the list below. Lot size Sample size (units) 800 or less 2 801 up to an