NAVY MIL-C-22667 B-1966 CABLE SPECIAL PURPOSE BUOYANT ELECTRICAL TYPE RG-298 U (SUBMARINE USE)《潜艇用RG－198／U型专门用途电动浮力缆索》.pdf

《NAVY MIL-C-22667 B-1966 CABLE SPECIAL PURPOSE BUOYANT ELECTRICAL TYPE RG-298 U (SUBMARINE USE)《潜艇用RG－198／U型专门用途电动浮力缆索》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-22667 B-1966 CABLE SPECIAL PURPOSE BUOYANT ELECTRICAL TYPE RG-298 U (SUBMARINE USE)《潜艇用RG－198／U型专门用途电动浮力缆索》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 flIL-C-22b67B bL 7797706 0088320 L W MIL-C -22667B( SHIPS) 11 May 1966 SUPERSEDING MIL-C - 22667A( SHIPS) 21 November 1961 MILITARY SPECIFICATION CABLE, SPECIAL PURPOSE, BUOYANT, ELECTRICAL, TYPE RG-298/U (SUBMARINE USE) 1. SCOPE 1.1 This specification covers special single-conductor buoyant cable

2、with high mechanical performance characteristics, such as high strength, flexibility, low compression set, low water absorption, low tempera- ture properties and abrasion resistance. # 2. APPLICABLE DOCUMENTS 2. 1 The following documents, of the issue in effect on date of invitation for bids or requ

3、est for proposal, form a part of this specification to the extent specified herein: SPECIFIC ATIONS FEDERAL L-P-390 - Plastic Molding Material, Polyethylene, Low and Medium Intensity. QQ-W-345 - Wire, Electrical, Steel, Copper Covered. MILITARY MIL-(2-17 - Cables, Radio Frequency; Coaxial, Dual Coax

4、ial, Twin Conductor, and Twin Lead. (Copies o specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contract- ing officer. ) 2. 2 Other publications. - The fol

5、lowing document forms a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. OFFICIAL CLASSIFICATION COMMITTEE Uniform Freight Classification Ratings, Rules, and Regulations (App

6、lication for copies should be addressed to the Official Classification Committee, 1 Park Avenue at 33rd Street, New York 16, N. Y. ) 3. REQUIREMENTS 3.1 Preproduction sample. - A preproduction sample shall be furnished for the inspection speciied in 4.2 (see 6.2). 3. 2 Materials and construction. -

7、3. 2.1 Center conductor. - The center conductor of the cable shall be stranded in accordance with # MIL-C-17. The conductor shall consist of seven strands of No. 24 AWG, high-strength, copper-covered (electroplated) wires, 30 2 percent conductivity, conforming to QQ-W-345. class L, grade 7 (natural)

8、 or 7a (colors) of L-P-390, having an outside diameter of O. 115 2 O. 004 inch. 3. 2. 2 Solid core dielectric. - The solid core dielectric shall be polyethylene in accordance with type II, . THIS DQGUMIENT CONTAINS PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted without li

9、cense from IHS-,-,-flIL-C-2i?bb7B b1 4Ob 0088321 3 MIL-C- 22667B(SHIPS) # 3.2.3 Jacket. - The jacket shall consist of two layers of continuous, homogeneous unicellular black foamed polyethylene. Minimum thickness of individual layers shall be O. 120 inch. The extreme outside diameter of the cable sh

10、all be O. 650 5 O. 025 inch. The outer layer of the jacket shall be of uniform hard- ness, and shall be free of major imperfections such as blow holes, cuts, valleys, and bruises. The jacket shall be manufactured from material which meets the requirements of type I, class L, grade 2 of L-P-390. 3.3

11、Breaking strength, - The center conductor of the cable shall have a minimum breaking strength of 400 pounds, 3.4 Shear strength, - 3.4.1 Between center conductor and solid core dielectric. - The shear strength between the center 3.4.2 Between solid core dielectric and inner or outer layer of jacket.

12、 - The shear strength between conductor and solid core dielectric shall be a minimum of 50 pounds per linear foot of cable. the solid core dielectric and the inner or outer layer of the jacket shall be a minimum of 50 pounds per linear foot of cable, 3.5 Specific gravity. - The cable shall have the

13、lowest possible overall specific gravity consistent with the requirements specified herein, The specific gravity shall not exceed O. 80 when tested as specified in 4.4.5. 3.6 Cold bend. - There shall be no evidence of cracks or flaws in either the dielectric material or the jacket, when tested .as s

14、pecified in 4,4.6. 3.7 Crack resistance. - The cable shall be resistant to stress cracking, when tested as specified in 4.4.7. 3,8 Bonding. - Bonding shall be accomplished by the proper appllcation of heat. The bond between the solid core dielectric and inner layer shall be non-continuous in such ma

15、nner that the jacket will be easily strippable in certain areas to effect an “O“ ring seat on the inner core dielectric without any additional preparation, These strippable areas shall be not less than 2 inches long in any linear foot of cable. The bond between the jacket layers shall be continuous

16、and construction shall not impair the strength requirements of 3.4. 3.9 Length, - Unless otherwise specified (see 6.1) cable shall be provided in not less than 2,000-foot 3.10 Marking, - 3,lO.l Manufacturers identification. - Manufacturers identification shall consist of coloring the solid a nor mor

17、e than 2,100-foot continuous (with no joint or splice) lengths. # dielectric core in accordance with a manufacturers identification color to be assigned by the bureau or agency concerned. Coloring of the core shall not affect the characteristics of the cable. There shall be no markings on the outer

18、surface of the cable, 3.10.2 Reel marking. - All reels shall be marked with cable designation, contract, date of manufacture, manufacturer, and lengths of cable. 3.11 Workmanship. - The workmanship shall be first class in every respect and uniform throughout each lot of cable offered for delivery. 4

19、, QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection, - Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facili

20、ties or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements, # Provided by IHSNot for

21、ResaleNo reproduction or networking permitted without license from IHS-,-,-.t MIL-C-22667B 61 W 9779706 0088322 5 W MIL-C - 22667B( SHIPS) # 4.1.1 Quality control system. - The supplier shall provide and maintain a quality control system which meets the requirements specified in the appendix. # 4.2

22、Preproduction inspection. - A 300-foot sample of cable constructed in accordance with this specification shall be subjected to the examination and tests specified in 4. 3. 2 and 4.4, # 4.2.1 Preproduction test report. - A report of the tests conducted shall be forwarded to the Bureau of Ships and th

23、e contracting officer. The manufacturer shall not initiate production prior to receipt of approval of this report except at his own risk. # 4.3 Quality conformance inspection. - . # 4,3,1 Sampling. - A 10-foot sample of cable shall be selected from every production run for the examination and tests

24、of 4. 3. 2, 4.4. 1, 4.4. 2, 4.4. 3, 4.4.4, and 4.4.5. Samples of sufficient length shall be selected from every 40,000 feet of cable for the tests of 4.4.6 and 4.4.7. 4.3,2 Visual and dimensional examination. - The samples selected in accordance with 4.3.1 shall be examined to verify that the design

25、, construction, physical dimensions, and workmanship are in accordance with this specification, 4.3. 3 Tests. - Samples selected in accordance with 4. 3.1 shall be subjected to the tests of 4.4. 4.4 Test procedures. - # 4.4.1 Dimensions and out-of-round. - The overall diameeer of solid core polyethl

26、yene dielectric and outer jacket shall be measured. The cable making equipment shall be fitted with electronic or mechanical measuring device(s) to produce graphic records of the cable produced. Two recordings shall be made as nearly simultaneously as possible of each diameter, 90 degrees apart, and

27、 at a point in manufacturing where further dimensional changes such as cooling, tension, and SO forth will not occur. permanent and reproducible by a-common commercial process. The recording accuracy shall be no less than ?. 5 percent of the tolerance being measured, and any portion of the recording

28、 shall be identifiable to within 2 2 feet of the cable being measured and not less than 1/20 of an inch of paper per each 1 foot of cable being monitored. Each recording shall be identified with the reel of cable being monitored. The beginning of .the cable length and end of the cablerun shall be in

29、dicated on the recordings. The recordings shall be # 4.4.1.1 Calibration. - The zero position on the graph and an indication of which side of zero is over and which side is under the nominal cable diameters shall be required, and an indication of specific values in thousandths of an inch shall be ma

30、de on the recording with-regard to he dielectric and outer jacket outside diameters. # 4.4. 2 Bonding. - The cable shall be tested for conformance with 3.8. 4.4.3 Breaking strength. - The breaking strength of the center conductor shall be determined by means of a power-driven tensile machine. The ra

31、te of travel of the power-actuated grip shall be adjusted to move at a rate of 2 5 1/2 inch per minute. A 20-inch specimen of center conductor shall be used for this test. # 4.4.4 Shear strength. - A suitable device shall be constructed to measure the shear strength between 4,4.5 Specific gravity. -

32、 The specific gravity shall be measured under a hydrostatic pressure of 600 each bond surface. Five 1-foot pieces shall be used for the tests. pounds per square inch gage (p. s. i, g. ) at room temperature in fresh water. The measurement shall be made after a continuous immersion of 24 hours. The ca

33、ble sample shall not be removed from the pressure tank nor the pressure reduced until after the measurement is completed. 4.4.6 Cold bend. - The cable shall be subjected to the cold bend test specified in MIL-C-17. 4.4. 7 Crack resistance. - The cable shall be tightly wrapped around a mandrel 3 inch

34、es in diameter continuously for 24 hours to determine conformance with 3.7. 4.5 Inspection conditions. - Unless otherwise specified herein, all inspections shall be made at room ambient temperature, pressure and humidity. 3 :rz- * 4 i-) ,.- -2- - .- t Provided by IHSNot for ResaleNo reproduction or

35、networking permitted without license from IHS-,-,-MIL-C-22667B(SHIPS) 6. PREPARATION FOR DELIVERY 5.1 Domestic shipment and early material use. - 5.1.1 Packaging, - Cable in the length specified (see 3.9) shall be packaged to afford adequate protection against deterioration and physical damage durin

36、g shipment from the supply source to the using activity and until early use. 5.1.2 Packing, - Packing shall be accomplished in a manner which will insure acceptance by common carrier and will afford protection against physical and mechanical damage during direct shipment from the supply source to th

37、e using activity for early use. The shipping containers or method of packing shall conform to tlie Uniform Freight Classification Ratings Rules, and Regulations or other carrier regulations as applicable to the mode of transportation, 5.1.3 Marking. - Shipment marking information shall be provided i

38、n accordance with the contractors cornmercime, The information shall include nomenclature, Federal stock number or manufacturers part number, specification number, contract or order number, date of manufacture (month and year), con- tractors name, and destination, 5.1.3.1 Marking of each reel or spo

39、ol shall be located on the flange area in a manner designed to pre- clude the possibility of the markingls becoming illegible during use. 5.2 Domestic shipment and storage or overseas shipment. - The requirements and levels of packaging, packing, and marking for shipment shall be specified by the pr

40、ocuring activity (see 6.1). 5.2.1 The following provides various levels of protection during domestic shipment and storage or over- ( 5.2.1.1 Packaging, packing, and marking. - Cable in lengths specified (see 3.9) shall be packaged level seas shipment, which may be required when procurement is made

41、(see 6.1). A Or C as specified (see 6. i), packed level A or 3 as specified (see 6.1) and marked in accordance with the requirements of MIL-C-OOO, ) 8. NOTES 6.1 Ordering data. - Procurement documents should specify the following: # (a) Title, number, and date of this specification. (b) Length if ot

42、her than specified in 3.9. (c) Level of packaging, packing, and marking required if other than as specified in 5.1 (see 5.2). 8.2 Preproduction. - Invitations for bids should provide that the Government reserves the right to waive the requirement for preproduction campies as to those bidders offerin

43、g a product which has been previously procured or tested by the Government, and that bidders offering such products, who wish to rely on such pro- ducfion or test, must furnish evidence with the bid that prior Government approval is presently appropriate for fhe pending procurement. MARKEXI “#“ TO I

44、NDICATE WHERE CHANGES (DELETIONS, ADDITIONS, ETC. ) FROM THE PREVIOUS ISSUE HAVE BEEN MADE. THIS HAS BEEN DONE AS A CONVENIENCE ONLY AND THE GOVERNMENT ASSUMES ET0 LIABILITY WHATSOEVER FOR ANY INACCURACIES IN THESE NOTATIONS, CONTRACTORS ARE CAUTIONED TO EVALUATE THE REQUIREMENTS OF THIS DOCUMENT BA

45、SED ON THE ENTIRE CONTENT AS WRITTEN IRRESPECTntE OF THE MARGINAL NOTATIONS AND RELATION- SHIP TO THE LAST.PREVIOUS ISSUE. # 6,3 CHANGES FROM PREVIOUS fSSUE, THE OUTSIDE MARGINS OF THIS DOCUMENT HAVE BEEN BIDDERS AND Preparing activity: Navy - SH (Project 6145-N145Sh) Provided by IHSNot for ResaleNo

46、 reproduction or networking permitted without license from IHS-,-,-MIL-C-22bb7B bL W 797770b 008832LI 7 W / MIL-C-22667B(SHIPS) APPENDIX QUALITY CONTROL SYSTEM REQUIREMENTS CABLE, SPECIAL PURPOSE, BUOYANT TYPE RG-298/U (SUBMARINE USE) 10. SCOPE 10.1 This appendix requires the establishment of a qual

47、ity control system by the contractor to assure that supplies meet the quality standards established by the contract. This system, including procedures, is subject to surveillance by the Government representative. The procedures shall be designed by the contrac- tor. the disapproval of the Government

48、 representative. The contractors procedures used to implement the requirements of this appendix shall be subject to 10. 2 Applicability. - This appendix shall apply to all supplies on which Government inspection is required. 10.3 Significance. - This appendix and any procedure or document executed i

49、n implementation thereof, shall be in addition to and not in derogation of other contract requirements. 20. REQUIREMENTS 20.1 Outline. - The contractor shall maintain an effective and economical quality control system planned and developed in conjunction with other planning functions. The system, including procedures, shall be adjusted to suit production procurement. The system shall be based upon consideration of the complexity of product design, quantity under procurement, i