NAVY MIL-C-18244 A (1)-1993 CONTROL AND STABILIZATION SYSTEM AUTOMATIC PILOTED AIRCRAFT GENERAL SPECIFICATION FOR《一般规格飞机自动控制和稳定系统》.pdf

《NAVY MIL-C-18244 A (1)-1993 CONTROL AND STABILIZATION SYSTEM AUTOMATIC PILOTED AIRCRAFT GENERAL SPECIFICATION FOR《一般规格飞机自动控制和稳定系统》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-18244 A (1)-1993 CONTROL AND STABILIZATION SYSTEM AUTOMATIC PILOTED AIRCRAFT GENERAL SPECIFICATION FOR《一般规格飞机自动控制和稳定系统》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-18244A (1) 9999906 1952780 572 = MIL-C-l8244A(AS) AMENDMENT 1 18 August 1993 MILITARY SPECIFICATION CONTROL AND STABILIZATION SYSTEM: AUTOMATIC, PILOTED AIRCRAFT, GENERAL SPECIFICATION FOR This amendment forms a part of MIL-C-l8244A(AS), dated 1 December 1962, nd i approved for use by the Nava

2、l Air Systems Command, Department of the Navy and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1: Delete and substitute: “2.1 Government documents .II “2.1.1 Specifications and standards. this document to the extent specified herein. Unless otherwise sp

3、ecified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards DODISS and supplement thereto, cited in the solicitation (see 6.21.“ The following specifications form a part of 2.1: II JAN- 1-2 2 5 I Delete the following cancell

4、ed documents: 0 JAN-T-78 1 II “MI L- E-4 6 8 2 I “MI L- E- 5 2 7 2 I “MIL-1-61 81 I “MIL-L-6880“ Bottom of page: Delete “FSC N/A“ and page number “1“ and insert below documents list: II Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improvin

5、g this document should be addressed to: Commanding Officer, Naval Air Warfare Center Aircraft Division Lakehurst, Systems Requirements Department Code SR3, Lakehurst, NJ 08733-5100, by using the self-address Standardization Improvement Proposal (DD Form 1426) appearing at the end of this document or

6、 by letter. AMSC NIA 1 of 5 FSC 1680 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-18244A (1) 779990b II952781 409 MIL-C-l8244A(AS) AMENDMENT 1 PAGE 2 2.1: Dele

7、te tne following cancel led documents: “MI L-0-8706“ “MIL-E-1 9600“ “MI L-R-222 56 II “MIL-R-23094“ Move “MIL-M-7793“ to its correct numerical pos1 tion below “MIL-E-7080“ 2.1.1: Add the following superseding documents under “MILITARY“ in their correct numer i cal or.der : “MIL-E-1 Electron Tubes, G

8、eneral Specification for“ “MI L-T-781 “MI L-T-5422 Testing, Environmental, Airborne Electronic and Associated Equipment“ “MI L-S-8805 “MIL-S-8805/1 Switches, Sensitive, SPDT, Unsealed“ “MIL-S-19500 Semiconductor Devi ce, General Specification for“ Termi na1 ; Wire Rope Swagi ng“ Switches and Switch

9、Assemblies, Sensitive and Push (Snap Action), General Specification for“ 2.11: numerical order: Add the following superseding documents under “STANDARDS“ in their correct “MIL-STD-200 Electron Tubes, Selection of“ “MIL-STD-461 “MIL-STD-462 “MI L-STD-701 Lists of Standard Semiconductor Devices“ “MIL-

10、STD-781 “MIL-STD-810 Environmental Test Methods and Engineering Guidelines“ “MIL-STD-838 Electromagnetic Emission and Suscepti bi 1 i ty Requirements for the Control of Electromagnetic Interference“ Electromagnetic Interference Characteristics Measurements of“ Reliability Testing for Engineering Dev

11、elopment Qualification and Product i on I Lubrication of Mi 1 i tary Equipment“ 2.1.1: “STANDARDS“ 1 i s t : Add the following parenthetical statement below last document listed below “(Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are avai lable

12、from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094)“ 2.2: Delete paragraph and substitute: “2.1.2 Other Government documents. part of this document to the extent specified herein. Unless otherwise specified, The following other Government docu

13、ment form a the issues are those cited in the solicitation. NAVAL AIR SYSTEMS COMMAND SD 8706 Design Examination, Engineering, Aircraft Weapons Systems General Spec i fi cat i on for II 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-L8244A (

14、1) 9999906 1952782 345 MIL-C-l8244A(AS) AMENDMENT 1 Add paragraph as fol lows: “2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related MS standards), the text of this document takes precedence. Nothing in this documen

15、t, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. PAGE 16 3.1.1.6.1, line 4, delete “Specification MIL-E-5272“ and substitute “MIL-STD-8 PAGE 18 O“ . 3.3.1, line 3, delete “MIL-E-4682“ and substitute MIL-STD-200, MIL-STD-701, MIL-E-1, MIL-T-19500.

16、Seventh line, delete whole sentence. 3.3.1.3, first sentence, delete “JAN-S-63, or MIL-S-6743“ and substitute “MI L-S-8805/ 1 , or MI L-S-8805“. 3.3.1.4, delete and substitute: “3.3.1.4 Electron Devices. Electron devices not specifically designated in the equipment detail specification or contract s

17、hall be selected and applied from MIL-STD-200, MIL-STD-701, and Navy Supplement to MIL-STD-200, and shall be in accordance with the requirements f the applicable specification (MIL-E-1 or MI L-T-19500). I O PAGE 19 3.3.1.7, line 2, delete “conforming to specificat 3.3.1.9, line 2, delete “MIL-L-6880

18、“ and substitu PAGE 22 3.5.1, line 8, delete last sentence. PAGE 25 on MIL-E-19600“ e “MI L-STD-838“. Add the fol lowing paragraphs and renumber “4.1 I to “4.2“ and subsequent paragraphs accordingly. “4.1 Unless otherwise specified in the contract or purchase order, the contractor is responsible for

19、 the performance of all inspection requirements (examinations and tests) as specified herein. specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless di sapproved by the G

20、overnment. right to perform any of the inspections set forth in this specification where such Responsibility for inspection. Except as otherwise The Government reserves the inspections are deemed necessary to ensure suppl ies and services conform to prescribed requirements.“ 3 Provided by IHSNot for

21、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-L244A (I) 9999906 1952783 281 = MIL-C-l8244A(AS AMENDMENT 1 “4.1.1 Responsibility for compliance. All items shall meet all requirements of I y.( sections 3 and 5. The inspection set forth in this specification shall be

22、come a par of the contractors overall inspection system or quality program. The absence of an inspectioli requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requ

23、irements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept def

24、ective material .II PAGE 26 4.3.5, line 4, delete “MIL-E-5272“ and substitute “MIL-STD-810“. PAGE 27 4.3.5.3, line 7, delete “Specification MIL-1-6181“ and substitute “MIL-STD-461 and MIL-STD-462“. Eight line, delete “Specification MIL-1-6181“ and substi tute “MI L-STD-461 and MI L-STD-462“ . PAGE 2

25、8 . 4.4.3, line 3, delete “Specification MIL-R-23094“ and substi tute “MIL-STD-781 .II PAGE 30 Section 6, add the following parenthetical note below the heading “NOTES“: “(This section contains information of a general or explanatory nature that may be helpful but is not mandatory)“ Section 6: “6.2

26、Acquisition requirements. Acquisition documents must specify the fo lowing: add the following paragraph and renumber the subsequent accord ngly: a. Title, number, and date of the specification. b. Issue of DODISS to be cited in the solicitation, and if required, the specific l issue of individual do

27、cuments referenced (see 2.1).“ I I 6.3: delete and substi tute: Electronic Maintainability“ will be available upon application to the Commander, Naval Air Systems Command, Air 53014 Washington, D.C. 20361“ i “Additional information on “Microelectronic Modular Assemblies“ and “Aircraft I I I Add para

28、graph as follows: 1 “6.5 Subject term (key word) listing.“ “Automated F1 ight Equipment“ “Automated F1 i ght Gui dance“ “Automated F1 ight Navigation“ “Automated F1 ight Systems“ “Microelectronic Modular Assemblies“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Cus tod i ans : Navy - AS NIL-C-18244A (1) W 9999906 1952789 118 MIL-C-l8244A(AS) AMENDMENT 1 Preparing activity Navy - AS (Project 1680-N612) Revi ew acti vi ti es : Army - AV 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-