NAVY MIL-B-82564-1968 BISTABLE MULTIVIBRATOR ASSEMBLY LD 546989 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)《LD 546989双稳多谐振荡器装置(MK 443 MOD 0 AND MOD 1制导控制测试装置用)》.pdf

《NAVY MIL-B-82564-1968 BISTABLE MULTIVIBRATOR ASSEMBLY LD 546989 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)《LD 546989双稳多谐振荡器装置(MK 443 MOD 0 AND MOD 1制导控制测试装置用)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-B-82564-1968 BISTABLE MULTIVIBRATOR ASSEMBLY LD 546989 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)《LD 546989双稳多谐振荡器装置(MK 443 MOD 0 AND MOD 1制导控制测试装置用)》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-E-82564 33 39Ob 0363938 3 1 - MILITARY SPECIFICATION BISTABLE MULTIVIBRATOR ASSEMBLY LD 546989 (For Guidance. Control Test Set MK 443 Mod O and Mod 1) This specification has been approved by the gava1 Ordnance Systems Cmand, Department of the Navy. 1. SCOPE 1.1 Bistable Multivibrator Assembly, L

2、D 546989 and BuWeps Dwg 2452610, herein referred to as ffassembly. ff (See 6,l for description and intended use.) This specification covers the requirements for the procurement of the 2. APPLICABLE DOCUMENTS 2.1 bids or request for proposal form a part of the specification to the extent specified he

3、rein. The following documents of the issue in effect on date of invitation for SPECIFICATIONS - . _. .- - . .* Federal PPP-B-636 Boxes, Fiber Military MIL -P -1 16 Preservation, Methods of Shockproof equipment, Class Hi (Hi Current: O to 150 ma; Lozd Regulation: Less than O. 3% from O to 150 ma.) Os

4、cilloscope (Bandpass: dc to 15 mc; Rise Time: O. 023 ,mec; Accuracy: 3% from 0.05 to 20 volts/cm.) Digital Voltmeter (Range: O. O01 to 999.9 vdc; Accuracy: -10.05% of reading *l digit.) Square Wave Generator (Frequency Range: 1 cps to 20 kc; Output: 25 volts peak across a 600-ohm load.) Multimeter (

5、Resistance Range: O to 20 megohms; Accuracy: within 3 degrees of arc on resistance scale.) . Bistable Multivibrator Test Fixture Identification Hewlett-Packard Model 721A Tektronix Model 535 A with Type CA Preamplifier Hewlett-Packard Model 3440A with 3442A Automatic Range Selector Hew1 ett-Packard

6、Model 211A Simpson Model 260 (consisting of the following components) (See figure 2) Circuit Symbol J1 Rl,R2;R3 R4, R5 R6, R7 c1 Sl,S3 s2 Part Connector Resistor, 1,000 ohm, 1/2 w Resistor, 100. k, 1/2 w Resistor, 165 k Al%, 1/4 w Capacitor, , O01 ufd, Switch, SPDT Switch, SPDT, Center C FF 600 VDC,

7、 *20% - Designation Amphenol 57-20140 Quantity 1 MS3 5 O 5 8 -2 1 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-825b4 13 m 7979906 0361928 4 m P1 1 BISTABLE MULTI VI BRATOR 2 7 9 10 3 6 4 5 11 14 12 B ISTABL E MU LT IV1 BRATO R *TEST FIXTUR

8、E COMMON 5 4 TPl i *!-a I NEGATIVE START-STOP SWITCH. 1 OFF- ; s1 1 I 1K R1 t 1/2w .1/2.w * 7 START-STOP TP54 1K R3 c - TEST CIRCU!T. 4-25 VDC POWER SUPPLY COMMON DIGITAL VOLTMETER INPUT 1 CHANNEL A OSCILLOSCOPE GROUND E: POWER SUPPLY I COMMON -15 VDC POWER SUPPLY GENERATOR 8 -2035-2 Provided by IHS

9、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-82564 33 m 7797706 0363727 b MIL-B-82564(0S) - . ! 1 4.7.3 Test procedure 4.7.3.1 Test setup 4,7.3,1.1 Turn on and. adjust the power supplies as follows: I Power Supply Limits (vdc) +25. O vdc +25. O *O. 6 -15,

10、O vdc -15. O *0.5 +9,5 vdc +9.5 it0.0 4.7.3.1.2 Turn off power supplies, and then connect assembly to the bistable multivibrator test fixture and to test equipment as shown in figure 2. 4.7.3.1.3 Position test fixture switches as follows: Switch Position s1 52 OFF 2 . .I_ -. . s3 i 4.7.3.2 Start and

11、 stop test . 4.7.3.2.1 Preliminary test (a) Turn on the +25, +9.5 and the -15 volt power supplies, and observe the digital voltmeter. The indication shall be +21. O to +24. O vdc. NOTE -Ifindicationin4.7.3.2.1is O,Oto+2.Ovdc, set switchS2 to position 1. Digital voltmeter shd indicate +21. O to +24.

12、O vdc. 4.7.3.2.2 Positive start and stop (a) Positive start. (1) Verify that switch S2 is set to position 1. (2) Set switches S2 and SS to position 2. Digital voltmeter shali indicate +21. O to +24. O vdc, and on switch S2 closure the oscilloscope shall display a level change with a rise time of 5 p

13、sec maximuni. - - - - - j -_ 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-82564 23 W 7777706 0362730 2 W - Mn-B-82564( OS) - (3) Set switch S3 to position 1. fiigital voltmeter shall indicate O. O to +2. O vdc. (b) Positive stop. (1) Set

14、switch S2 to position 1. The oscilloscope shall display a level change with a fall time of 5 pec maximum. Digital voltmeter shall indicate +21. O to +24. O vdc. (2) Set switch S3 to position 2. Digital voltmeter shall indicate O. O to +2. O vdc. 4.7.3,2,3 Negative start and stop .i (a) Negative star

15、t. (1) Set switch S3 to position 1, and switch S1 to position 2; then set to OFF position, The oscilloscope shall display a level change with a rise time of 5 psec maximum. Digital voltmeter shall indicate O. O to t.2. O vdc. (2) Set switch 53 to position 2. Digital voltmeter shall indicate t-21.0 t

16、o +24.0 vdc. . (b) . Negaive stop. (1) Set switch S1 to position 1, then set to OFF. Digital voltmeter shall indicate O. O to +2. O vdc, and the oscilloscope shall dis- play a level change with a time of 5 psec maximum. (2) Set switch 53 to position 1. Digital voltmeter shall indicate +21. O to +24.

17、 O vdc. (3) Turn off the +9.5 .volt power supply. 4,7,3 3 Diode steering 4,7.3.3.1 Turn on the square wave generator, and adjust the frequency to 2 cps. Adjust the output for a 9.5 ;O. 5 vp-p square wave, with a rise and fall time of 5 psec maximum. 4.7.3.3.2 Set switch S3 to position 2. Digital vol

18、tmeter indication shall alternate between O. O to +2. O vdc, and +21. O to +24. O vdc, at a 1 cps rate. Oscilloscope display shall indicate a square wave with a rise and fall time of 5 psec maximum, 4.7.3.3.3 Turnoff +25 and-15 vdcpower supplies. 4,7.3,4 Resistance measurements, Ramove assembly from

19、 test fixture, and with multimeter measure resistance from assembly test points to pins of connector P1 as shown in table IV. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-2564 13 7799906 O361731 4 = Assembly Test Point P1 Connector Pin TP1,

20、TP4 14 TP2 7 TP3 3 c Table IV Resistance (Ohms) 9,000 to 11,000 0.5 max O. 5 max , Resistance Measurements I I Between I 4.7.4 Examination of product. The assembly shall be examined for con- formance to the requirements specified herein and on the drawings listed in LD546989. The presence of any one

21、 of the following defects shall constitute a failure. (a) Assembly not complete; components or parts missing. (b) Unauthorized material used or unauthorized repairs made, (c) Dents , scrapes, nicks , bent pins, poor electrical connections , or any other damage as determined by the procuring activity

22、. (d) Receptacles .do not accept mating plugs. (e) Identification markings missing, located incorrectly, illegible or incomplete, 5. PREPARATION FOR DELIVERY 5.1 Preservation and packaging, Preservation and packaging shall be Level A or C as specified (see6.2). 5.1.1 Level A 5,l. 1.1 Cleaning. Clean

23、ing, if necessary, shall be in accordance with process C-1; and drying, if required, shall be in accordance with procedure D-1 or D-4 of MIL-P-116, 5.1.1.2 Unit packaging. Unit packaging of the assemblies shall be in accord- ance with Method IIb of Specification MIL-P-116. The unit package shall con

24、tain one assembly in fiberboard containers, The outer container shall be in accordance with Specification P.PP-B-636; Style RSC; Type CF; Class - Weather resistant; Variety SW; Grade V3c. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-82561, (

25、OS) 5.1.1.3 Intermediate package. Kot applicable. 5.1.1.4 Cushioning. The unit package, and pack, shall incorporate sufficient cushioning material, bracing, or other adequate shock absorbing devices, to assure that the assembly will meet all the requirements of Section 3 after trans- portation. Cush

26、ioning material and packaging procedure shall be such that the assembly shall not be contaminated with dust or foreign materials. At the time of packaging or packing, the moisture content of the cushioning material shall be no more than 5 percent, The pH range of the material shall be between 6, O a

27、nd 8.0. 5.1.2 Level B, Not applicable. 5.1.3 Level C. Cleaning, drying, preservation and packing shall be in accordance with the suppliers commercial practice when such practices are approved by the procuring activity. 5.2 Packing I -. 5.2.1 Level A 5.2.1.1 Eherior containers, Assemblies, packaged a

28、s described in 5.1.1.2, shall be packed in a fiberboard container in accordance with Specification PPP-B-636; Style RSC; Type CF; Class - Weather resistant; Variety SW; Grade V3c. Exterior containers shall contain the number of unit packages specified in the contract or order (see 6.2) or, in the ev

29、ent no quantity is specified, the number of unit packages packed shall be at the option of the contractor. 5.2.2 Level B Not applicable. 5.2.3 to afford protection against damage during direct shipment from the supply source to the first receiving activity for immediate use. Shipping containers shal

30、l conform to the carrier rules and regulations applicable to the mode of transportation, 5,3 Marking J Level C. Assemblies, packaged in accordance with 5.1, shall be packed . 5.3.1 Normal markings, In addition to the markings required by contract or order, unit packages and shipping containers shaU

31、be marked in accordance with the requirements of MIL-STD-129, including serial numbers. 6. NOTES 6.1 Description and intended use 6.1.1 Description. The assembly generates output signals, which are used to start and stop an electronic counter, for measuring torpedo timing functiolis. 6.1.2 Test Set

32、Mark 443 Mod O and Mod 1, used to veri.%- compliance 117ith performmce requirements of the Torped.) Mark 46 at Fleet level. Intended use, The assembly is an int.3gral part of the Guidance Control f f -I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

33、-MIL-B-825b4 33 9779906 O363933 - . - _.- - Mz-3-82564 (OS) 6.2 Ordering data. Procurement documents shall specify the following: (a) Title, number and date of this specification, (b) Required level of preservation and packaging, and packing. (c) Packing quantity. (d) Assigned activity for preproduc

34、tion and periodic tests, (e) Any exceptions to this specification. (f) Provisions for additonal samples required because of failure of any sample(s) to pass the prescribed inspections, (g) Required data. 6.3 Definitions 6,3.1 frequency, The amplitude may refer to displacement or acceleration. The di

35、splacement is given in one half the peak-to-peak excursion in inches or the cor- responding maximum acceleration in gravity units (g). The frequency is given in cycles per second (cps). 6.3.2 Shock, Shock is an abrupt change in the position of a body, resulting from the sudden application of a large

36、 external force of short duration. Shock is described as a pulse force in units of gravitational acceleration (gls), of duration in units of time, milliseconds (ma), and a shock wave approximating a one-half sine wave. The time duration shall be measured between trvo points where two lines intersect

37、 the zero ltgft line. These lines are tangent to the shock wave slopes. Vibration. Vibration is a sinusoidal motion defined by amplitude and 6.4 of preservation, packaging, and packing shall be as follows: Preparation for delivery criteria, Criteria for use of the proper level Level A This level sha

38、ll be used for those items which are to be shipped to indeterminate destinations or stored under indeterminate .conditions for redistribution anlwhere. Level B Not applicable. Level C This level shall be used only when it is definitely known that the packaged item is to be shipped to domestic instal

39、lations for immediate use at the first receiving activity. Custodian: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-82564 (OS) APPENDIX - CONTRACTOR CERTIFICATION GOVERNMENT ACCEPTANCE Contractor Date of Acceptance Contract Accepted by Equipm

40、ent Ser. No. Title Insp. Req. Satisfied Agency w - REPORT FORM QUALITY CONFORMANCE TESTS AND EXCIMINATIONS FOR BISTABLE MULTIVIBRATOR ASSEMBLY LD5469 89 (For Guidace Control Test Set Mk 443 Mod O and Mod 1) EQUIPMENT STATUS r Provided by IHSNot for ResaleNo reproduction or networking permitted witho

41、ut license from IHS-,-,-Assembly Serial No, Date APPENDIX REPORT FORM QUALITY CONFORMANCE TEST AND EXAMINATION 10. o Quality conformance test and examination Scope. This report form contains data sheets to record the re.sults - 10.1 of the quality conformance tests and examinations of 4.7 of this sp

42、ecification, 10.2 Verification. Where a limit or limits are provided, the value of a specific reading obtained shall be recorded. If limits are not provided, satis- factory compliance of the requirement must be verified. 10,3 Test results ! Reference Limits Reading 10.3.1 Test equipment 4.7.2 In cal

43、ibration L 10.3.2 Test procedure 4.7.3 10.3.2.1 Start and stop test 4.7.3.2 Preliminary test 4.7.3.2.1 P1-10 voltage - (4 +21. O to +24. O vdc Positive start and stop 4.7.3.2.2 I Positive start. (a) P1-3 voltage (2) +21. O to +24. O vdc Voltage rise time 5 psec max P1-10 voltage (3) O. O to +2, O vd

44、c Positive stop (b) P1-10 voltage (1) +21. O to +24. O vdc Voltage rise time 5.psec max I P1-3 voltage (2) 0.0 to +2.0 vdc Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-82564 33 999990b 0363936 3 Assembly Serial No. Date 10.3.2.1 Negative sta

45、rt and stop (Cont) Negative start P1- 1 O .vol tage Voltage rise time Pl-3 voltage Negative stop Pl-3 voltage Voltage rise time Pl-10 voltage 10.3.2.2 Diode steering Pl-3 voltage Voltage rise and fall time 10.3.2.3 Resistance measurements TP1, TP4 to Pl-14 TP2 to P1-7 TP3 to Pl-3 10,4 Examination of

46、 product 10.5 Preservation and packaging Readiw Limits -4 Reference 4.7.3.2.3 O. O to +2. O vdc 5 psec max (2) +21. O to +24. O vdc . (1) O.Oto +2.O vdc 5 psec max (2) +21. O to +24. O vdc 4.7.3.3 4i7.3.3.2 Alternates be- tween O, O to +2. O vdc and +21. O to t-24. O vdc at 1 cps rate 5 psec max 4.7.3.4 - 9,oooto 11,000 ohms 0.5 ohm max O. 5 ohm-max 4.7.4 Satisfactory . 5.1 Satisfactory Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-