NAVY MIL-A-22305 C-1963 AMPLIFIER DISTRIBUTION AM-2123 (V) U《AM-2123 (V) U分配放大器》.pdf

《NAVY MIL-A-22305 C-1963 AMPLIFIER DISTRIBUTION AM-2123 (V) U《AM-2123 (V) U分配放大器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-A-22305 C-1963 AMPLIFIER DISTRIBUTION AM-2123 (V) U《AM-2123 (V) U分配放大器》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-A-22305C (SHIPS) 16 October 1963 SUPERSEDING 14 February 1962 (See Section 6.3) MIL -A -223 05B (SHIPS) MILITARY SPECIFICATION AMPLIFIER, DISTRIBUTION AM-2123/U 1. SCOPE 1.1 This specification covers requirements of a transistorized radio frequency (r-f.) amplifier used in shipboard standard-fre

2、quency distribution systems. Amplifier channels are provided for 5 megacycles (mc.), 1 mc. and 100 kilocycles (kc.) signals. Power gain and isolation between channels are provided. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request fo

3、r proposal, form a part of the specification to the extent specified herein. SPECIFICATIONS FEDERAL J-C-175 - Cable Assembly, Power, Electrical, (3-Wire, 3-Prong, Grounding Plug Connector, for 125-Volt Equipment). MILITARY MIL-L-3661 MIL-P-15024 - Plates, Identification-Information and Marking for I

4、dentification of Electrical, MIL-E-16400 - Electronic Equipment, Naval Ship and Shore: General Specification. MIL-E-17555 - Electronic and Electrical Equipment and Associated Repair Parts; Preparation MIL-R-22732 - Reliability Requirements for Shipboard and Ground Electronic Equipment. - Lampholders

5、; Lights, Indicator; Indicator-Light Housings; and Lenses, Indicator Light, General Specification For. Electronic and Mechanical Equipment. for Delivery of. STANDARDS MI LIT ARY MIL-STD-108 - Definitions of and Basic Requirements for Enclosures for Electric and Elec- MIL-STD-189 - Racks, Electrical

6、Equipment, 19-Inch and Associated Panels. MIL-STD-242 - Electronic Equipment Parts (Selected Standards). MIL-STD-736 - Unitized Equipment Design. tronic Equipment. DRAWINGS BUREAU OF SHIPS REA49028 - UG-625B/U Connector Receptacle, Series BNC. PUBLIC ATIONS BUREAU OF SHIPS NAVSHIPS 93820 - Handbook

7、for the Prediction of Shipboard and Shore Electronic Equipment Reliability. (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contract- ing offi

8、cer.) I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-A-22305C 58 7779906 035075q I m 3.0 NIIL-A-22305C(SHIPS) 2.2 ther publications.- The following document forms a part of this specification to the extent specified herein. Unless otherwise in

9、dicated, the issue in effect on date of invitation for bids or request for proposal shall apply. OFFICIAL CLASSIFICATION COMMITTEE Uniform Freight Classification Rules. (Application for copies should be addressed to the Official Classification Committee, 1 Park Avenue at 33rd Street, New York 16, N.

10、 Y.). 3. REQUIREMENTS 3.0 0.75 .- 3.1 Qualification.- The equipment furnished under this specification shall be a product which has been tested, and passed the qualification tests specified herein, and has been listed on or approved for listing on the applicable qualified products list. except as ot

11、herwise specified herein. 3.2 General requirements.- The equipment shall be in accordance with all provisions of MIL-E-16400, 3.2.1 Reliability.- The following is an outline of the general reliability requirements specified in MIL- r E-16400 as it is applicable to this equipment. 3.2.1.1 -.- The rel

12、iability goal for this equipment shall be 10,000 hours mean-time-between-failure 3.2.1.2 Reliability evaluation shall be performed in accordance with the procedures for Weliability As- 3.2.1.3 Testing.- For test purposes, demonstration of attainment of a reliability level of 300 hours (MTBF). suranc

13、e by Analysis and Prediction“ as specified in MIL-R-22732. MTBF with a 90 percent confidence level will be required. (See 4.1.3) be submitted whenever the design changes or additional design data becomes available affecting the prediction. 3.2.1.4 In addition to the regular reliability reports of MI

14、L-R-22732, reliability prediction reports shall 3.3 Mechanical design.- 3.3.1 Modular construction.- The equipment shall be designed for modular construction in accordance with MIL-STD-736, except that test points and test features are not required. Twelve amplifier channels shall be provided, each

15、channel consisting of one modular assembly with its input and output connections. Module size shall be in accordance with table I. The equipment power supply may be mounted directly to the chassis, or it may be partially or wholly contained in plug-in assemblies. Table I - Assembly size. Inches 2 3.

16、3.2 Channel frequency selection.- The 12 channefk to be provided shall be arranged SO that any of the channels can serve any of 3 frequencies, 5 mc, 1 mc. and 100 kc. Individual assemblies shall be designed for operation at one of these frequencies. Frequency service for a given channel shall be sel

17、ected by inserting an amplifier assembly of the desired frequency. No switching or wiring changes shall be required to select a channel frequency. The equipment shall be capable of use with any number of assemblies from O to 12 plugged in, with normal operation on the channels in use. each of the 3

18、frequencies, unless otherwise specified in the contract or order. Input characteristics shall be such that any number of assemblies from O to 12 may be plugged in to serve any of the 3 frequencies. 3.3.3 Number and frequency of channels.- The equipment shall be supplied with 4 assemblies serving - P

19、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.4 Connectors.- 3.3.4.1 Assembly connectors.- Requirements of MIL-STD-736 apply, except that power and signal input and output connections shall be made thru the same connector for each assembly. Inpu

20、t No. 1 shall be consid- ered 5 mc. input, likewise No. 2 shall be 1 mc., and No. 3 shall be 100 kc. Outputs from all assemblies shall be connected thru pins identified with output No. 1. 3.3.4.2 Chassis connectors.- Signal input and output connectors type UG-625 B/U, in accordance with REA49028 sha

21、ll be located at the rear of the equipment. One input connector shall be for each of the 3 fre- quencies. Connection shall be made to furnish input signals of the 3 frequencies to the appropriate pins on all chassis receptacles. One output connector shall be provided for each amplifier assembly, and

22、 shall be con- nected to one assembly only. or output, and the frequency served. Output connectors shall be numbered from 1 thru 12. Each connector shall be conveniently identified to the assembly it is serving. 3.3.4.3 Connector identification.- All signal connectors on the chassis shall be marked

23、to indicate input 3.3.5 Enclosure and mounting.- The equipment shall be capable of 19-inch rack mounting and separate shelf mounting. The outer enclosures shall be dripproof in accordance with MIL-STD-108, and may be remov- able for rack mounting of the equipment. Drawer slides shall be provided for

24、 withdrawing the chassis from the enclosure or rack. 3.3.6 e.- The total enclosed volume shall not exceed one-third cubic foot. Limiting dimensions for rack mounting shall be as specified in MIL-STD-189. The overall dimensions of the equipment with outer en- closure shall not exceed the dimensions s

25、hown in table II. Table II - Overall dimensions. 21 inches Height 8-3/4 inches Depth 3.3.7 Weight.- The total equipment shall not exceed 16 pounds. 3.3.8 Accessibility.- All parts shall be readily accessible for test (with equipment in operation), and for replacement or repair without injury to or r

26、emoval of other parts or wiring, Chassis withdrawal and access to all parts and assemblies shall be from the front of the equipment. 3.3.9 Temperature class.- The equipment shall meet the class 4 temperature requirements. 3.3.10 Shock class.- For shock tests, the equipment shall be classified as gra

27、de A, class I, light weight, type A. 3.4 Electrical design. - 3.4.1 - Duty.- The equipment shall be capable of continuous operation. 3.4.2 Power source.- The equipment shall be designed to operate from either 115 volts, 50 to 400 Cycle, single phase, or 22 to 30 volts direct current (d.c.). Connecti

28、on to the 115 volt source shall be thru a cable assembly permanently attached to the rear of the equipment and conforming to Type II of J-C-175. A suitable connector shall be provided on the rear of the equipment for connection to the d.c. source. Circuitry to the d.c. power connector shall be such

29、that an external battery will furnish standby power, with no break in oper- ation of the equipment, in case of a 115 volt power failure. The internal power supply shall not load the ex- ternal battery during such a power failure. lampholder style LH74LC13CN conforming to MIL-L-3661, and associated n

30、eon lamp, to indicate power on“. 3.4.2.1 Power indicator.- An indicator light shall be provided on the front panel in accordance with 3.4.2.2 Blown-fuse indicators.- Blown-fuse indicators shall be provided in accordance with MIL-STD- 242. 3 Provided by IHSNot for ResaleNo reproduction or networking

31、permitted without license from IHS-,-,-MIL-A-22305C 58 9790b 01507bL T W MIL-A-22305C(SHIPS) 3.4.3 Input characteristics.- * 3.4.3.1 Frequency.- Three separate input channels shall be provided: one each for 5 mc., 1 mc., and 3.4.3.2 e.- The equipment shall be designed for operation at any input leve

32、l between 0.5 and 5.0 3.4.3.3 Impedance.- Input impedance on each channel shall be no less than 50 ohms with 12 amplifier 100 kc. volts (V). A manual adjustment for different input levels will be acceptable if necessary. assemblies connected to that channel. 3.4.4 Output characteristics.- 3.4.4.1 =.

33、- Output level shall be between 4.0 and 5.0 V measured across any load impedance between 3.4.4.2 Bandwidth.- The bandwidth of each frequency shall be less than 2 percent of input frequency for 3.4.4.3 Distortion.- Any single distortion product shall be at least 80 db below signal level, except har-

34、3.4.4.4 Isolation.- The signal at any output connector shall be unaffected by a short circuit on any num- 3.4.5 Metering.- A front panel meter with suitable switching shall be provided for selective monitoring 50 ohms and 1 megohm. 3 decibels (ab) down, and 10 percent for 30 db down. monics shall be

35、 at least 60 db down, on each signal line. ber of other output circuits. of operating conditions of important circuits, including power inputs and all outputs. A means shall be pro- vided to indicate proper meter readings for all circuits monitored, either a green area on the meter, or an informatio

36、n plate, type A or B in accordance with MIL-P-15024, attached to the front panel. ally required; the input level controls if used shall be infrequently required and have suitable locking devices. 3.4.6 Controls.- No power switch shall be provided. The panel meter selector switch shall be continu- 4.

37、 QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.- Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein, Except as otherwise specified, the supplier may utilize his own faciliti

38、es or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the speci- fication where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Classification of t

39、ests. - Qualification tests as specified herein, and quality conformance inspection as specified in MIL-E-16400 shall be performed on the equipment. 4.1.2 Test procedure approval. - Procedures for all required inspections, including descriptions of test equipment to be used, shall be submitted to th

40、e bureau or agency concerned for approval at least 30 days be- fore tests are scheduled to begin. number 3. The test time on each equipment shall be not less than 450 hours and not more than 720 hours. If an accept decision cannot be made before 720 hours on an equipment, the test shall be terminate

41、d and the re- quired reports of the tests shall be submitted to the bureau or agency concerned for the decision to accept or reject. With all inputs energized, three output lines shall be monitored, one at each frequency, for level across 50 ohms. Violating the limits of 4.0 to 5.0 volts shall const

42、itute a failure. If input level controls are used, they may be set initially, but may not be adjusted during the test. Reliability testing shall be conducted on one out of every 25 units produced. 4.2 Qualification tests.!./- Qualification tests shall be conducted at a laboratory satisfactory to the

43、 Bureau of Ships, Qualification tests shall consist of the tests specified in table IIi and 4.4. Three complete equipments shall be submitted for qualification inspection. 4.1.3 Reliability testing.- Reliability tests shall be performed as specified in MIL-R-22732 for test level /Application for dal

44、ification tests shall be made in accordance with “Provisions Governing Qualification“ (see 6.2 and 6.2.1). 4-/- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A -223 05C (SHIPS) Table - Qualification tests. Inspection Group I Surface examination

45、 Operating test Weights and dimensions Heat Enclosure Power line voltage and frequency Group II Signal level Bandwidth Impedance Isolation Distortion Group Di Temperature Humidity Shock and vibration inclination Salt spray test Accelerated life Reference MIL-A-22305C 5B 777370b OL503b2 I W - MIL-E-1

46、6400 MIL-E-16400 MIL-E -16400 MIL-STD-108 and 3.3.5 MIL-E-16400 and 3.4.2 3.3.6 and 3.3.7 4.4.1 4.4.2 4.4.3 4.4.4 4.4.5 MIL-E-16400 MIL-E -1 64 O0 MIL-E -16400 MIL-E-16400 MIL-E-16400 MIL-E-16400 4.3 Quality conformance inspection. - Quality conformance inspection shall consist of the following: (a)

47、 Production inspection. (b) Production control inspection. (c) Environmental tests. 4.3.1 Production inspection.- Production inspection shall be made on every equipment offered for deliv- ery and shall comprise such examination and tests as will prove the workmanship and reveal possible omis- sions

48、and errors in the production process. Production inspection shall include the tests shown in table IV. Table IV - Production inspection. I Inspection 1 Reference I Operating test MIL-E-16400 4.3.2 Production control inspection.- Production control inspection shall be conducted on equipments which ha

49、ve passed the inspection of 4.3.1. Inspection shall be conducted to detect any deterioration in the de- sign by wear of such items as dies, molds, jigs, fixtures, and to detect deviations in the material or part processing, selection, or assembly, and to detect any deterioration in the performance of the equipment not discernible under the inspection of 4.3.1. As equipments are produced and their number increases, sample units shall be selected in accordance with table V. I. - - 5 Provided b