NAVY A-A-59311-1998 PACKAGING MATERIAL KRAFT PAPER 3-PLY FLEXIBLE [Superseded NAVY MIL-P-29596 CANC NOTICE 1 NAVY MIL-P-29596]《3-PLY弹性牛皮纸包装材料 [代替 海军 MIL-P-29596 CANC 通告 1 海军 MIL-P-.pdf

《NAVY A-A-59311-1998 PACKAGING MATERIAL KRAFT PAPER 3-PLY FLEXIBLE [Superseded NAVY MIL-P-29596 CANC NOTICE 1 NAVY MIL-P-29596]《3-PLY弹性牛皮纸包装材料 [代替 海军 MIL-P-29596 CANC 通告 1 海军 MIL-P-.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-59311-1998 PACKAGING MATERIAL KRAFT PAPER 3-PLY FLEXIBLE [Superseded NAVY MIL-P-29596 CANC NOTICE 1 NAVY MIL-P-29596]《3-PLY弹性牛皮纸包装材料 [代替 海军 MIL-P-29596 CANC 通告 1 海军 MIL-P-.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-59311 = 9018054 0003897 bb3 COMMERCIP ITEM DE I INCH-POUND 1 17 November 1998 SUPERSEDING 15 January 1993 A-A-593 1 1 MIL-P-29596(NAVY) XIPTION PACKAGING MATERIAL, KRAFT PAPER, 3-PLY, FLEXIBLE The General Services Administration has authorized the use of this commercial item description for all

2、federal agencies. 1. SCOPE. This commercial item description (CID) covers the requirements for flexible 3-ply kraft paper for use in dunnage packaging operations. 2. SALIENT CHARACTERISTICS. 2.1 Raw material. Packaging materials covered under this specification shall be made from kraft material conf

3、orming to A-A-203. 2.1.1 Construction. The materials shall be constructed in any manner that forms a 3-ply configuration. The plies shall be plainy layered and shall be non-bonded. 2.2 Form. The material specified in 2.1.1 shall be furnished in rolls. The roll material shall be uniformly wound on no

4、nreturnable cores. The cores inside diameter shall be not less than 3 inches, with a tolerance of + O. 125 inch. The length of the core shall be equal to the width of the roll material, with a tolerance of + O. 125 inch. The core shall be rigid to prevent distortion of the roll during use and shipme

5、nt conditions. Each roll shall be restrained to prevent unwinding. 2.2.1 Roll dimensions. Unless otherwise specified (see 5.2), the average length shall be not less than 150 yards. The length of any individual roll shall be not less than 145 yards. If rolls are specified with an average length that

6、exceeds 150 yards the individual roll length tolerance shall be -5 percent. Unless otherwise specified, the width of roll material shall be 30 inches with a tolerance of i 0.25 inch. E rolls are specified in widths exceeding 30 inches the tolerance shall be 22 percent. if rolls are specified in widt

7、hs less than 30 inches the tolerance shall be 20.5 percent. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data which may improve this document should be sent to: Commander, Naval Air Warfare Center Aircraft Division, Code 414100B120-3, Highway 547, La

8、kehurst, NJ 08733-5100. FSC 8135 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I A-A-593 11 2.3 Packaging material (conversion). Roll materials specified in 2.2 and 2.2.1 shall be capable of being converted

9、into packaging materials with portable equipment and processes developed by the manufacturer. 2.4 Identification sheet. Each lot or order shall contain the specification number, manufacturers designation, manufacturers name, lot number, and date of manufacture. 2.5 Contact corrosivity. The kraft pap

10、er shall have no corrosion, etching, or pitting in the contact area when tested in accordance with FED-STD- 1 O 1, Method 3005, 2.6 Abrasiveness. The kraft paper shall not rupture, tear or produce a macroscopic scratch on the material or metai surface when tested in accordance with 3.3.2. 2.7 Low te

11、mperature flexibility. The kraft paper surface shail have no cracks, tears, or separation when bent over a manrel and tested in accordance with 3.3.3. 2.8 Vibrational settling. The kraft paper samples average thickness decrease shall be not greater than 15 percent, and the thickness decrease of any

12、one sample tested shall be not greater than 20 percent when tested in accordance with 3.3.4. 3. QUALITY ASSU”CE PROVISIONS. 3,l Product Conformance. The products provided shall meet the salient characteristics of this commercial item description, codorm to the producers own drawings, specifications,

13、 standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 3.2 Market acceptability. The following market acceptability criteria is necessary to document the quality of the pr

14、oduct to be provided under this commercial item description: The company frnishing the kraft paper must have been producing a product meeting the requirements of this commercial item description for at least 6 months. 3.3 Testing. All tests shall be conducted as specified herein. 3.3.1 Test conditio

15、ns. Unless otherwise specified, tests shall be conducted at a temperature of 72 2 2 OF and a relative humidity of 50 _+5 percent. 3.3.2 Abrasiveness. 3.3.2.1 Procedure. A specimen of packaging material shall be placed on the surface of a polished 2024T2 aluminum panel conforming to QQ-A-250/4. The a

16、iuminum panel shall be wider than the packaging material and long enough to permit the packaging material to be pulled along the 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-593LL m 9ClL805ii COO3899 T3b m A-A-593 1 1 panel is specified her

17、ein. A weight exerting a force of 1 .O 2 O. 1 psi shall be placed on top of the packaging material. The weighted packaging material shall be pulled horizontally 6.0 I0.5 inches back and forth along the panel for 30 cycles at a speed of 1 foot (1 cycle) per second. The weight shall then be removed an

18、d this procedure shall be repeated using the other side of the specimen in direct contact with the same plate. 3.3.3 Low temperature flexibilitv test. 3.3.3.1 Conditioning. Cut four specimens, 4 by 12 inches, and condition for 3 hours at -20 2 2 OF. The specimens shall be arranged in a low temperatu

19、re chamber so that the air can circulate against all surfaces of the specimens. A 0.25 inch steel diameter mandrel and the test specimens shall be placed in the low temperature chamber simultaneously. 3.3.3.2 Procedure. Mer low temperature conditioning, immediately bend each specimen over the mandre

20、l so that the specimen is subjected to a 180 degree bend. Bending shall be accomplished at the conditioning temperature. The flexing operation over the mandrel shall take 2 to 3 seconds. Each specimen shall be bent over the mandrel 3 times with one face against the mandrel and then turned over so th

21、at the opposite face of the specimen is toward the mandrel; the bending procedure is then repeated as described above. 3.3.4 Vibrational settling test. 3.3.4.1 Cleated plywood box. A cleated plywood box conforming to PPP-B-601, Style A (except as specified herein) shall be fabricated. The box shall

22、have interior dimensions of 10 by 10 by 10 inches with a tolerance of + 0.0625 inch. The plywood panels shall be 0.5 inches thick. The lumber for cleats shall be nominal 1 by 2 inch material. No cover is necessary. 3.3.4.2 Prototype load. A rigid prototype test load shall be fabricated of wood, stee

23、l, aluminum, or other rigid materials. In order to provide a 100 square inch bearing area on the packaging material, the prototype test load shall have length and width dimensions of 1 O by 1 O inches with a -0.0625 tolerance for each. The prototype shall be constructed in such a manner that the loa

24、d-bearing surface is flat. The prototype load shall be designed so that its weight provides a bearing stress of O. 1 O f 0.01 psi. In addition, an accelerometer shall be mounted to the prototype load. 3.3.4.3 Pack assembly. The inside bottom surface of the cleated plywood box shall be covered with 1

25、00 f 5 grams of the packaging material to be tested. 3.3.4.4 Test Drocedure. Place the completed pack upon a vibration table in the configuration shown on figure 1. Place the prototype test load on the test specimen and immediately vibrate the entire test xture at O. 5 Gs through a frequency sweep o

26、f 5 Hz to 1 O0 Hz (vertical linear) at a rate of 2 octaves/minute. Note the fiequency at which resonance occurs (natural frequency). Record 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59311 m 9038054 0003700 588 m A-A-593 1 1 the material i

27、nitial thickness immediately following frequency sweep (allow the load to remain on the material). Run at the natural frequency for 30 f 0.5 minutes and record the final material thickness. Three samples shall be tested. The average thickness decrease of the three samples and the thickness decrease

28、of any one sample shd be not greater than the requirement specified in 2.8. The thickness decrease shall be calculated in accordance with 3.5.1.4. 3.5.1.4 Calculations. Calculate the percent thickness decrease utilizing the following formula: x 100 percent (TF- TI) TF TD = TF = finalmaterialthicknes

29、s TI = initial material thickness TD = percent material thickness decrease A - Spacer B - 22 inch guide C - Accelerometer D - Graduated cylindrical guide bar E - Hydraulic actuator and table components F - 10 by 10 inch prototype load x 4 x 4 FIGURE 1. Test fixture confimiration. 4 Provided by IHSNo

30、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59311 = 90l18054 0003901 414 A-A-593 1 1 4. PACKAGING. 4.1 Preservation. packing. and marking. Preservation, packing, and marking shall be as specified in the contract or order. 5. NOTES. 5.1 Usage. 5.1 - 1 Intended

31、 use. The packaging materials covered by this specification are intended for use primarily as dunnage in packing or shipping applications where a flexible, non-plastic material is required. 5.1.2 Other use. In certain applications, at the discretion of the acquiring activity, these packaging materia

32、is may be used in cushioning applications. It is recommended that in those instances, testing be conducted to determine the adequacy of the material to perform as a cushioning material. These materials may be oriented in such a manner to enhance their ability to provide primary cushioning protection

33、. The manufacturer may be able to furnish idormation as to particular material Orientations that may yield the desired results. 5.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of this specification. b. Issue of the DODISS to be cited in th

34、e solicitation, and ifrequired, the specific issue of individual documents referenced. c. Number of rolls (see 2.2. i). d. Length of rolls (if other than 150 yards) (see 2.2.1). e. Width of rolls (if other than 30 inches) (see 2.2.1). 5.3 Federal Standards and Specifications may be obtained from the

35、 General Services Administration Specifications Section, Suite 8 100,470 E. LEdnt Plaza, SW, Washington, DC 20407. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593 1 1 MILITARY INTERESTS: custodians: Navy - AS CIVIL AGENCY COORDINATING ACTIVITY: GSA/FSS-2FYE Preparing activity: Navy - AS (Project 8 13 5-NOO3) Review activities: Navy - SA 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-