NAVY A-A-50633-1994 GLOVES LEATHER GAUNTLET DRUMMER-S《交叉射击皮革手套》.pdf

《NAVY A-A-50633-1994 GLOVES LEATHER GAUNTLET DRUMMER-S《交叉射击皮革手套》.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-50633-1994 GLOVES LEATHER GAUNTLET DRUMMER-S《交叉射击皮革手套》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-50b33 = 9999974 0364909 3TO = A-A-50633 August 1, 1994 SUPERCEDING August 1, 1973 MIL-G-82167 COMMERCIAL ITEM DESCRIPTION GLOVES, LEATHER; GAUNTLET: DRUMMERS The General Services Administration has authorized the use of this commercial item description in preference to MIL-G-82167. 1. SCOPE 1.1

2、Intended use. This commercial item description covers requirements for white leather unlined gauntlet gloves for use by band members. 2. SALIENT CHARACTERISTICS 2.1 Salient characteristics. The gloves shall be sheepskin leather, dyed white, outseamed, unlined, with two piece gauntlet cuff lined with

3、 vinyl plastic and leather binding at top edge, three rows of ornamental stitching on the back, Bouton thumb, and one or two piece fourchettes. 2.1.1 Leather. The leather shall be sheepskin from hair sheep, dyed white of good quality (no boardy/flanky leather) and 2 to 3 ounce thick for palms, thumb

4、s, backs, fourchettes and binding and 2 1/2 to 3 1/2 ounce thick for the cuff. 2.1.2 Lininq. The cuff lining shall be 0.020 to 0.002 inch thick white vinyl plastic. 2.1.3 Thread. The thread for sewing the gloves shall be white nylon of suitable strength and size. 2.1.4 Adhesive. The adhesive for joi

5、ning the cuff and cuff lining shall be a good grade of rubber cement suitable for the purpose. Beneficial comments, recommendations, additions, deletions clarification, etc. and any data which may improve this document should be sent to: Commander (PSE-C), Marine Corps Systems Command, Quantico, VA

6、22134-5010. msc N/A FSC 8440 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50633 W 9999974 OLb49LO 012 W A-A- 50633 2.2 Sizes. The gloves shall be provided in hal

7、f sizes from size 7 1/2 through size 11. The following finished measurements for a size 9 are provided as a guide in sizing. (see Figure 1.) Measurements Inches A- Top edge of cuff to tip of second finger 14 1/2 B- Bottom edge of cuff to tip of second finger 8 1/2 C- Across palm at thumb crotch 4 li

8、8 D- Tip of index finger to thumb crotch 4 3/4 E- Thumb crotch to tip of thumb 2 3/4 F- Across bottom edge of cuff 4 3/4 G- Across top edge of cuff 7 3/4 2.3 Label. Gloves shall have a commercial style label providing the contractors name and size. 3. REGULATORY REQUIREMENTS 3.1 Requlatorv reuuireme

9、nts. The contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent possible, 4. QUALITY ASSURANCE 4.1 Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product c

10、onforms to the producers own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on cont

11、ractor quality assurance systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. 4.2 Visual examination. Gloves shall be examined for the defects listed below in

12、accordance with ANSI/ASQC-Z1.4. 4.3 Defects. Any hole, cut, tear, boardy or flanky leather, color not white, stain, open seam, thread ends not trimmed, distorted parts, label missing or incorrect. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. A

13、-A- 50633 5.PACKAGING 5.1 Preservation, Dacking and marking. Preservation, packing and Gloves will be paired marking shall be a good commercial practice. by individual size. 6. NOTES 6.1 Source of Government documents. Copies of military and Federal documents are available from: Standardization Docu

14、ments Order Desk Bldg 4D 700 Robins Avenue Philadelphia, PA 19111-5094 6.2 Sources of Non-Government documents. ANSI/ASQC-Z1.4 Sampling procedures for inspection by attributes. (Applications for copies should be addressed to American National Standards Institute, 11 West 42nd Street, New York, NY 10

15、036.) MILITARY INTERESTS Navy - MC CIVIL AGENCY COORDINATING ACTIVITY: GSA- FSS PREPARING ACTIVITY Navy - MC Project No. 8440-N211 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50633 m 9999974 OLb49L2 995 m A-A-5 O 6 3 3 FRONT BACK FIGURE 1. GLDVEZ;, LEATHER: GAUNTLET: DRUMMERS 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-