NAVY A-A-50598-1992 KIT PHOTOLUMINESCENT MARKING《冷光标记照片工具包》.pdf

《NAVY A-A-50598-1992 KIT PHOTOLUMINESCENT MARKING《冷光标记照片工具包》.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-50598-1992 KIT PHOTOLUMINESCENT MARKING《冷光标记照片工具包》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-50578 42 m 9999974 0067073 O m A-A-50598 22 May 1992 COMMERCIAL ITEM DESCRIPTION KIT, PHOTOLUMINESCENT MARKING The General Sewices Administration has authorized the use of this Commercial Item Description. Abstract. This Commercial Item Description covers two sizes of Photolumines- cent Marking

2、Kits and two types of stencils to be used to establish an emergency egress/damage control marking/paint system (one coat of primer, two coats of photoluminescent paint, and one coat of protective top coat) on the interior of U.S. Navy surface ships and submarines. The size of kit is identified by th

3、e amount of photoluminescent paint in each kit. Salient characteristics. 1. Two sizes of kits and two types of stencils are required as follows: a. The ten gallon kit consists of the following items: (1) Ten l-gallon cans of photoluminescent paint. (2) A sufficient quantity of l-gallon cans and l-qu

4、art cans of surface primer to cover an equivalent effective surface area covered by ten gallons of photoluminescent paint. (3) A sufficient quantity of l-gallon cans and l-quart cans of clear protective top coat to cover an equivalent effective surface area covered by ten gallons of photoluminescent

5、 paint. (4) Three 7-inch paint rollers. (5) Twelve 7-inch paint roller covers. (6) One stir stick for each container of photoluminescent paint, primer, and top coat. b. The five gallon kit consists of the following items: (1) Five l-gallon cans of photoluminescent paint. (2) A sufficient quantity of

6、 l-gallon cans and l-quart cans of surface primer to cover an equivalent effective surface area covered by five (5) gallons of photoluminescent paint. Beneficial comments, recommendations, additions, deletions, clarifi- cations, etc. and any other data which may improve this document should be sent

7、by letter to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101. AMSC N/A FSC 4240 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

8、om IHS-,-,-A-A-50598 42 = 9999974 00b7072 2 A-A-50598 (3) A sufficient quantity of 1-gallon cans and 1-quart cans of clear protective top coat to cover an equivalent effective surface area covered by five gallons of photoluminescent paint. (4) Three 7-inch paint rollers. (5) Twelve 7-inch paint roll

9、er covers. (6) One stir stick for each container of photoluminescent paint, primer, and top coat. c. Surface ship stencil package. d. Submarine stencil package. 2. Photoluminescent Paint a. Shall employ water as its solvent and have a maximum volatile b. Shall be a 1-component material. c. organic c

10、ontent (VOC) of 250 grams per liter. Shall exhibit a sag index of no less than 12 mils (1 mil = 1/1000 inch) wet using Federal Test Standard Number 141 Sag Test Method 4494 on a vertical surface. (OF) using test method specified in ASTM D93. roller. Shall have a minimum effective surface coverage of

11、 75 square feet per gallon, obtained in two coats with a film thickness equivalent to that obtained using the provided roller. d. Shall have a flash point of no less than 100 degrees Fahrenheit e. Shall be applied evenly and without streaks using a fine nap paint f. g. Shall have a minimum shelf sto

12、rage life of one year. 3. Primer a. b. d. e. f. g. h. C. i. k. j. 1. Shall employ water as its solvent and have a maximum VOC of 250 grams per liter. Shall remain acid-free upon aging. Shall be free from heavy metals such as lead chromate or iron. Shall be a 1-component material. Shall be bright whi

13、te in color. Shall not be lifted from the surface when the photoluminescent paint is being applied over it. Shall not react to either the surface being primed or the photo- luminescent paint being applied over it. Shall adhere to all types of interior surfaces including wood, aluminum, steel, and th

14、ermal fibrous glass insulation board Shall adhere to painted and unpainted surfaces. Shall have a minimum shelf storage life of one year. Shall have a minimum surface coverage of 250 square feet per gallon, obtained in one coat with a film thickness equivalent to that obtained using the provided rol

15、ler. Shall have a flash point of no less than 100F using the test method specified in ASTM D93. (MIL-1-742). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 O067073 4 A-A-50598 c m. Shall exhibit a sag index of no less than 12

16、mils (1 mil - 1/1000 inch) wet using Federal Test Standard Number 141 Sag Test Method 4494 on a vertical surface. Shall allow a corrosion rate of no more than nine when applied to steel using ASTM D610-85. n. 4. Clear Protective Top Coat a. Shall employ water as its solvent and have a maximum VOC of

17、 250 b. Shall be transparent non-yellowing adhering compound for mechanical c. Shall be 1-component material. d. Shall not react with the Photoluminescent paint layer or stencil e. Shall have a minimum surface coverage of 250 square feet per grams per liter. protective purposes. paint of Federal Spe

18、cification TT-E-489, class A. gallon, obtained in one coat with a film thickness equivalent to that obtained using the provided roller. f. Shall have a flash point of no less than 100F using the test method specified in ASTM D93. g. Shall exhibit a sag index of no less than 5 mils (1 mil = 1/1000 in

19、ch) wet using Federal Test Standard Number 141 Sag Test Method 4494 on a vertical surface. 5. Paint System a. b. C. d. e. It shall be guaranteed by the manufacturer that for a three year period after application of this paint system (one coat of primer, two coats of photoluminescent paint, and one c

20、oat of protective top coat) on any U.S. Naval surface ship or submarine the properties of these materials will still satisfy requirements set forth in this document. Failure to satisfy these requirements will be cause for the manufacturer to provide, at no cost to the Government, enough material to

21、reapply the paint system to the defective areas. The applied paint system shall have a flame spread index of no more than 10 using ASTM E162 Radiant Panel Test. The applied paint system shall have smoke generation values of no more than 120 and 60 for flaming and non-flaming condition respectively,

22、using ASTM E662 Smoke Chamber Test. Using test method specified in ASTM D2248, the applied paint system shall prove to be chemically resistant to detergent solution. Using luminance measurement method specified in MIL-L-3891, the applied paint system, when applied with the kit paint roller, shall pr

23、ovide the following luminance after specified periods of time after excitation of the material has ceased: (1) 20 microlamberts after 2 minutes. (2) .4 microlamberts after 30 minutes, (3) .1 microlamberts after 2 hours. (4) .O4 microlamberts after 4 hours. (5) .O1 microlamberts after 8 hours. 3 Prov

24、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5059 42 9999974 O067074 b - A-A-50598 f. Components of the paint system, when tested as specified in Method 4335 of Federal Test Standard Number 141, shall be accomplished using a paint roller system an

25、d without causing excessive drag on the roller cover. smooth, uniform appearance, and shall be free from sags, runs, wrinkles, roller marks, or any other film defects. Components of the paint system shall be certified mercury free. material other than that which is naturally occurring, and shall not

26、 rely on radioactive decay of any of its constituents to produce luminescence. g. When dry, the coated surface shall exhibit good adhesion with a h. i. Components of the paint system shall contain no radioactive 6. Paint Rollers, 7-Inch a. Shall be in accordance with Federal Specification H-R-550. b

27、. Shall have plastic grips. 7. Paint Roller Covers, 7-Inch a. Shall be fine nap, having a pile height between 1/8 inch and 3/8 b. Shall be slip off. c. Shall be chemically resistant to all paints provided under this inch. document. 8. Stencils a. b. C. d. e. f. g. h. i. The designs for stencils to b

28、e provided by the contractor shall be as specified in figure 1 (surface ship kit) and figure 2 (sub- marine kit). A maximum tolerance of 1/32 inch for each dimension will be allowed for the cut stencils. Shall be constructed of clear plastic between 1/32 and 1/16 inch thick. Shall be chemically resi

29、stant to stencil paint TT-E-489. Shall resist capillary action of the stencil paint. Shall be cleaned after paint has dried on it. Shall be resistant to cracking, tearing, and deformation for a minimum of 1000 applications of striping paint TT-E-489. If any stencil fails to meet the requirements set

30、 forth in this document the contractor shall provide a replacement. Stencil package shall be clearly labeled as to its content, surface ship or submarine stencils. 9. Application Instructions. The manufacturer shall provide detailed application instructions with each photoluminescent marking kit. Ou

31、alitv assurance Drovisions. None additional. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 O067075 8 A-A-50598 Contractor certification. The contractor shall certify, and maintain substan- tiating evidence, that the product o

32、ffered meets the salient characteristics of this Commercial Item Description, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and th

33、ereafter as may be otherwise provided for under the provisions of the contract. Metric Products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the tolerances specified using conversion tables

34、contained in the Commercial Item Description are met. c latest revision of Federal Standard No. 376, and all other requirements of this n If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the co

35、ntracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. Rewlatorv - requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practical. P

36、reservation. vackaninn, vackinn. labelinn. and markinq. The preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order. Notes. Purchaser should specify size of kit and type of stencils. Copies of military and federal specifications and standards are availa

37、ble from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. Copies of ASTM standards may be obtained from the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Prepari

38、ng activity: (Project 4240-0580) Navy - SH 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 O067076 T A-A-50598 10 u c-l NOTES: 1. All measurements are in inches. 2. Dimensions marked with an “;ti mean spaces between letters and

39、 numbers shall be of uniform width. Typical spacing between letters is 3/8 inch. FIGURE 1. Surface ship stencil packane 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5059 42 9999974 0067077 Z W A-A-5 05 9 8 U 1-1/2 142J 14 -1/4 I FIGURE 1. Su

40、rface shiD stencil Dackage (contd). 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 0067078 3 cr Y b 5 511-1 t Z/T-1 Il0 7- FIGURE 1. Surface shiD stencil Dackage - (contd). 8 Provided by IHSNot for ResaleNo reproduction or net

41、working permitted without license from IHS-,-,-A-A-50598 42 W 9997774 00b7077 5 A-A-5 05 98 1 - 1/4 1-1/4 4-1/2 FIGURE 1. Surface ship stencil Dackage - (contd). 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 O067080 L U A-A-5

42、0 5 9 8 0 U I 1-1/4 FIGURE 1. Surface shiD stencil packape (contdl. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 W 9949974 00b7081 3 W A-A-5 05 98 FIGURE 1. Surface ship stencil package (contd). 11 Provided by IHSNot for ResaleNo r

43、eproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 0067082 5 A-A-50598 FIGURE 1. Surface ship stencil package (contd). 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9799971.1 O067083 7 A-A-505 9 8

44、n I-.- - - 1 5-1/2 5 - 1/2 2 4 -1/2 e FIGURE 1. Surface ship stencil packape (contd). 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 = 9999974 0067084 9 A-A-5 05 98 FIGURE 1. Surface ship stencil package (contd). 14 Provided by IHSNo

45、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 0067085 O A-A-5 O 5 9 8 I- -I FIGURE 1. Surface ship stencil package (contd) 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c c A-A-50598 Y2 999

46、9974 006708b 2 A-A-505 98 v -11 -3 f FIGURE 1. Surface ship stencil package (contd). 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 9999974 O067087 4 A-A-5 O 5 9 8 c -I 5-1R FIGURE 1. Surface ship stencil package (contd). 17 Provided

47、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50538 42 m 9799974 0067088 b m A-A-50598 5 -3/4 I I 1 I.1 P- 11 - 1n t 4 FIGURE 1. Surface ship stencil package (contd). 18 e Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

48、ense from IHS-,-,-A-A-50598 42 W 9999974 00b7089 8 D A-A-505 9 8 b r i I FIGURE 1. Surface shir, stencil Dackave (contd). 19 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 W 9999974 00b7090 Y = A-A-505 98 12 I I FIGURE 1. Surface ship stencil package (contd). 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50598 42 = 9939974 00b709