NAVISTAR TMS 6502-2001 Urethane Cellular Molded (Revision C-1).pdf

《NAVISTAR TMS 6502-2001 Urethane Cellular Molded (Revision C-1).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR TMS 6502-2001 Urethane Cellular Molded (Revision C-1).pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. Ge32001 by International Truck and Engine Corporation. AUGUST 2001 Page 1 of

2、 2 INTERNATIONAL TRUCK AND ENGINE CORPORATION (TMS) TRUCK MATERIAL SPECIFICATIONNUMBER: TMS-6502 TITLE: Urethane, Cellular, Molded REVISION: C-1 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering DATE ISSUED: August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR C

3、URRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicabilit

4、y of regulatory limits prior to use. Change Notice: Reformatted and Editorial Changes Reference: File 30-16B Keywords: Urethane Foam, Urethane Padding 1.0 APPLICATION This specification covers a molded cellular polyurethane material which is used as an instrument panel crash padding and other interi

5、or trim applications where shock absorbing is needed. Optional: A specially formulated synthetic latex. 2.0 SCOPE This specification covers the general requirements, property and performance requirements, quality, source and quality control, qualification, and packaging. 3.0 REFERENCE DOCUMENTS Unle

6、ss otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard QS-9000 (ISO 9001) FMVSS 201 INTERNATIONAL IQR Quality Standard FMVSS 107 INTERNATIONAL Manufacturin

7、g Standard D-13 FMVSS 302 CFR Title 29, Part 1910 INTERNATIONAL TMS-9544 4.0 GENERAL REQUIREMENTS 4.1 Material Molded cellular polyurethane or synthetic latex processed to meet the requirements of the latest issue of Federal Motor Vehicle Safety Standard No. 201 and TMS-9544. 4.2 Gloss Material used

8、 in interior trim applications such as an instrument panel shall meet the surface gloss reflectance requirements on the finished surface of the latest issue of Federal Motor Vehicle Safety Standard No. 107. 4.3 Manufacture The urethane foam shall be processed so that it can be molded to a slush mold

9、ed plastisol skin or ABS plastic sheet with and without polymers. NUMBER: TMS-6502 TITLE: Urethane, Cellular, MoldedREVISION: C-1 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Su

10、ppliers are required to assume all patent liability. Ge32001 by International Truck and Engine Corporation. AUGUST 2001 Page 2 of 2 4.4 Description The color, finish, and gloss of finished parts shall match approved master samples in the Styling Department, TDTC. 4.5 Property And Performance Require

11、ments 4.5.1 Flammability Material and parts supplied to this specification shall conform to and be certified by the supplier to meet the requirements of Federal Motor Vehicle Safety Standard No. 302 - Flammability of Interior Materials, and all requirements of TMS-9544. 5.0 QUALITY The finished part

12、 shall be free from intense or offensive odor. Residual parting agent on the surface of the finished part shall in no way contribute to contamination, fading, or discoloration of the plastisol skin surface. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements Suppliers must conform to t

13、he requirements of the International IQR Quality Standard which includes conformance to the QS-9000 (ISO 9001) Quality System Standard. A mutually acceptable Quality Control Plan as described therein is required for source approval to the requirements of this specification. 6.2 Approval Parts suppli

14、ed against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples, which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processin

15、g practices, construction, color, or labeling of the product are required, the supplier shall notify International TDTC and International Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new o

16、r amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced or provide statistical evidence o

17、f the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using International plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING,PACKING AND IDENTIFICATION Parts shall be packed in suitable containers to afford protection against damage during shipment and storage, and shall meet the requirements of Manufacturing Standard D-13.