NAVISTAR MPAPS S-A-0 101-2015 Foreword.pdf

《NAVISTAR MPAPS S-A-0 101-2015 Foreword.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS S-A-0 101-2015 Foreword.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 3 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-A-0.101 Former Designation: ESP-A-0.101 TITLE: Foreword CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-A-0.101 - September 2008 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVIS

3、ION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulat

4、ory limits prior to use. Change Notice: Changed to New MPAPS format. 1.0 GENERAL: The standards contained in this book are compiled and published by Corporate Technical Standards. These standards, particularly those covering common hardware (bolts, nuts, screws, fittings, etc.) comply, where possibl

5、e, with standards published by the International Organization for Standardization (ISO) and worldwide national standards organizations such as the American National Standards Institute (ANSI) and the Society of Automotive Engineers (SAE). 2.0 INDEXES: Section A contains an Alphabetical Index, Materi

6、al and Finish Abbreviations, and Finish Specifications. The Alphabetic Index provides an alphabetic listing of products covered by the Standard Parts Book and indicates the section in which each can be found. 3.0 PART NUMBER ASSIGNMENTS: All part numbers appearing in this book are controlled by Corp

7、orate Technical Standards. Upon request part numbers are assigned to new and reinstated standard parts by Corporate Technical Standards from the special block of numbers reserved for that purpose. Drawings are not required and, in fact, must not exist for Corporate standard parts. 4.0 REQUESTS FOR S

8、TANDARD PARTS PAGES FOR SUPPLIERS: Suppliers requiring Engineering Standard Parts pages for price quotation or firm order purposes must contact the distributor of those documents for either one-time purchase or for subscription purposes. The Standards are available in printed form, on a CD-ROM or on

9、 a controlled access Internet Web site. Information on these options may be obtained by contacting the distributor at the address shown below. Information Handling Services 15 Inverness Way East Englewood, CO 80112-5776 NUMBER: MPAPS S-A-0.101 TITLE: Foreword REVISION: 1506 This document is restrict

10、ed and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 3 5.0 STANDARD PARTS: These are parts which have had minimum corporate criteria establi

11、shed for standardization of size, material, finish, general physical and performance characteristics, or a combination of these attributes. The criteria are established by consensus of the companys product engineering departments and reflect the parameters within which Group approved parts policies

12、are established. 6.0 HARDWARE PARTS: Hardware is a term used to describe a particular segment of the corporate standard parts commodities that are available as commercial products in various forms and sizes such as bolts, nuts, pins, clamps, washers, and fittings. 7.0 APPROVED PARTS: “Approved“ is t

13、erms used to segregate the parts within a recommended standard parts commodity to reduce variety and assure maximum availability, interchangeability, and cost savings. “Approved parts“ meet the minimum established corporate criteria for standardization of size, material, finish, and general physical

14、 characteristics. The criteria normally are established by consensus of the company product engineering departments and reflect the parameters within which Group approved parts policies are established. With a few exceptions, the general specifications for each type of part include a detailed outlin

15、e of the approved parts policy. 8.0 NOT FOR NEW DESIGN: This is a term used to describe certain standard parts commodities that should not be used in new or revised product designs and, if practical, should be replaced by another design in present products. These commodities normally are placed in t

16、his category as a result of a consensus of the product engineering departments to discontinue use of parts which either have been removed form national standards, or are difficult to procure, or are proprietary parts that limit availability and competitive pricing. There are also cases where other d

17、esigns exist that are interchangeable and technically equivalent or superior, less expensive, more readily available, etc. In rare instances, a “not for new design“ commodity may possess unique design characteristics for special applications for which a substitute commodity does not exist. In these

18、cases, the unique characteristics and examples of special applications will be described for which the commodity may be used. It must be remembered, however, that the listed special applications are not carte blanche approval to use the commodity, and every attempt must be made to design the applica

19、tion to avoid use of the parts. 9.0 SERVICE ONLY PARTS: “Service Only” is the term used for the parts which are no longer used in the production and made available only for service. 10.0 VOID PARTS: This term is used for the items which are voided in the systems like spectrum, team center, CDMS. NUM

20、BER: MPAPS S-A-0.101 TITLE: Foreword REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 3 11.0 DEL

21、ETED PART NUMBERS: Periodic usage searches are conducted throughout Navistar operations to confirm approved parts listings and to eliminate items no longer in use. The deleted list of part numbers is maintained by Corporate Standards and information regarding these numbers may be obtained by contact

22、ing the Parts Standardization Section. The increasing exchange of design within our company on a worldwide basis and the increasing number of internationally accepted parts a standard has made it advisable to establish a program for incorporating metric standard parts in the Enginee10-32ring Standar

23、d Parts Book. The following is a reaffirmation of the Corporate Metric Policy Committees agreements reached previously. 1. The Policy in changing to new Metric Series Parts Standards will be to adhere whenever possible to international standards, or standards with strong potential for international

24、recognition. 2. Usage of metric series parts should start when parts availability and economics are optimum for a division. The timing of such releases is a problem to be worked out by each division and its product groups. 3. New metric based standards will only be used after publication as our Corp

25、orate Engineering Standards. 4. Such new standards will only be introduced into new major components such as engines and transmissions, or into complete new machines. 12.0 PARTS NUMBERING: The following policy for obtaining part numbers for metric parts will apply: 12.1 Published Metric Standards: C

26、orporate Standards will assign all part numbers for metric standards published, in the Standard Parts Book. 13.0 DOCUMENT-BASED DOCUMENT CONTROL: These Engineering Standard Parts were converted to document-based document control approximately 5 years ago. Previously, the documents were basically con

27、trolled at a page number level. Users of these documents at that time occasionally fell into the inadvisable practice of referring to individual page numbers in documentation and now are unable to find those page numbers. The contents have not disappeared; they are just accessed at a document level.

28、 14.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/