NAVISTAR MPAPS G-6046-2016 Elastomeric Coatings.pdf

《NAVISTAR MPAPS G-6046-2016 Elastomeric Coatings.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS G-6046-2016 Elastomeric Coatings.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 1 of 8 NAVISTAR, INC. Material, Parts, and Process Specifications

2、(MPAPS) NUMBER: MPAPS G-6046 Former Designation: TMS-6046 TITLE: Elastomeric Coatings CURRENT REV No.: 1606 DATE: June 2016 WRITTEN/EDITED BY: S. Brailey APPROVED BY: R. Goluch SUPERSEDES: Rev. 0906 June 2009 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification ma

3、y involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use.

4、1.0 APPLICATION This specification applies to elastomeric coatings, generally polyurea, urethane and hybrids of those polymers. This specification may be applied to chemicals purchased to coat parts or parts coated by a supplier. 2.0 SCOPE This specification covers the qualification and processing,

5、quality, quality control and source approval, and packaging requirements of chemicals and finished parts. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.

6、0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 MPAPS P-9543 SAE J243 CFR Title 29, Part 1910 ASTM D

7、395 SAE J400 NAVISTAR Manufacturing Std. MS-D-13 ASTM D412 NAVISTAR Engineering Design Std A-16 ASTM D573 NAVISTAR MPAPS B-50 ASTM D624 MPAPS DT-12 ASTM D2137 MPAPS GT-31 ASTM D2240 MPAPS GT-Paint ASTM D4878 4.0 REQUIREMENTS This specification is not intended to limit or to specify the exact process

8、es and/or materials to be used in providing finished parts. The control of the primer quality and its application are the responsibility of the supplier. All finished coated parts shall be compatible with all subsequent NAVISTAR operations. NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION:

9、1606 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 2 of 8 4.1 Qualification of Coatings 4.1.1 Material/Process Ap

10、provals The coatings and pre-treatments used by the supplier must be approved by Materials Engineering prior to their first use in production. In addition, parts coated with the materials and applications processes/methods to be used by the supplier shall be approved by Materials Engineering and, af

11、ter approval, no deviation in materials and/or manufacturing processes are permitted without approval by Materials Engineering. 4.1.2 Material The initial qualification tests of paint shall be performed on parts formed from the same material and by the same process in which the finished parts are sp

12、ecified. These panels shall be coated with the materials to be tested using the procedure listed below. In cases where a primer is specified in addition to the topcoat, the panels shall contain both coatings applied by the intended production process. These panels shall be submitted to Materials Eng

13、ineering for approval with the vendors test results. Final qualification shall be performed on the finished part prior to production release. 4.1.3 Sample Preparation 4.1.3.1 A minimum of three (3) parts shall be submitted for qualification for each test. 4.1.3.2 Prior to coating, the samples shall

14、be cleaned with solvents or cleaners as necessary. This operation shall simulate production procedure. 4.1.3.3 The primer, if applicable, shall be applied to a minimum dry film thickness per the manufacturers recommended process. 4.1.3.4 The coated samples shall be cured by means which simulate prod

15、uction procedures. 4.2 Testing Finish painted parts, primed or unprimed, when coated with approved materials will meet the applicable requirements listed in Table 1. 4.2.1 Coatings used in flooring applications will meet the requirements listed in the table below in addition to Table 1. Test Test Me

16、thod Requirements Accelerated Weathering MPAPS GT-31 Method E Expose separate sets of samples to 100 and 500 hours continuous QUV-A light at 40C No color change greater than E of 3, plasticizer migration, delamination, or tackiness after 100 hours exposure. Report 500 hour results. Flammability FMVS

17、S 302 Meet the requirements of the latest issue Coefficient of Friction ASTM D2047 0.8 minimum Hardness (5 points) ASTM D2240 Type A 5 Tensile Strength (MPa) ASTM D412, Die C 5 minimum Low Temperature Resistance ASTM D2137, Method A Non-brittle at -40C (-40F) Pass Tear Resistance (kN/m) ASTM D624, D

18、ie B 15 minimum Heat Resistance ASTM D573, 70 hrs at 70C Hardness ASTM D2240 Type A 10 (max. % change) Tensile Strength ASTM D412, Die C 30 (max. % change) Tear Resistance ASTM D412, Die C -50 (max. % change) Mandrel Flexibility Test ” mandrel Pass 4.3 Material Properties Table 2 lists the required

19、cured material properties. NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION: 1606 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navist

20、ar, Inc. JUNE 2016 Page 3 of 8 4.4 Chemical Properties Table 3 lists the as-received chemical properties of the raw materials. This is only applicable to material received in this state by a using Navistar facility. 4.5 Processing Finished painted production parts shall be produced by the same metho

21、ds used on the qualification samples. Changes in processing must be approved by Materials Engineering. 5.0 QUALITY Painted parts shall be adherent and uniform in color and texture, with no thin spots, runs, wrinkles, porosity, pits, blisters or nodules. Material supplied shall be free from objection

22、able odor, be of uniform quality, and shall match performance properties of pre-production approved material. Pre-production samples of material sufficient for complete test and evaluation should be submitted to Materials Engineering for approval 5.1 Porosity In instances where porosity is not detec

23、table until after the primed substrate has been painted, isolated cases of porosity as defined in Table 4 shall not be cause for rejection. Porosity that is chronic and requires significant amounts of rework shall be cause for rejection and it is the responsibility of the supplier to correct this co

24、ndition. The supplier has the responsibility to provide quality primed parts which will not cause delayed defects after finishing in the using plant. This condition will require close cooperation with the paint facility and with Materials Engineering. 5.2 Appearance Requirements Specific appearance

25、requirements are given in Table 4. Appearance requirements are specified for the following zones or locations on the vehicle: 5.2.1 Zone I Primary: exterior, glamour surfaces such as hoods and fender exteriors, including visible edges, grilles, cab fronts, sides, doors, corners, and lower aerodynami

26、c fairings. 5.2.2 Zone II Secondary: exterior, glamour surfaces such as cab tops, cab backs (between corner radii), and upper aerodynamic fairings. Also, primary interior, surfaces, such as engine covers. 5.2.3 Zone III Recessed exterior or interior surfaces, such as door openings, door ends, painte

27、d grab handles, and floors or beds. 5.2.4 Zone IV Hidden areas, such as those covered in assembly and under hood or body. 5.2.5 Inspection Conditions Parts shall be inspected for appearance requirements at a distance of two feet under a light intensity of 100 foot-candles minimum at the part surface

28、. 5.3 Qualification Samples shall be accompanied by test data certifying that all requirements of the specification have been met. Data submitted shall include the following: 5.3.1 Report: A detailed and signed report documenting testing to this specification prepared in accordance with MPAPS P-9543

29、. The report will include actual test data and not merely test summaries. 5.3.2 Failure Modes: Test samples or photographs showing failure modes for each destructive test 5.3.3 Test Procedure: The procedures used for preparing and testing material. NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings RE

30、VISION: 1606 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 4 of 8 5.3.4 Analysis: A detailed analysis of the test

31、 results including assumptions made, unexpected results and an explanation of any non-compliant results. 5.3.5 Material: Pre-production material sufficient for complete test and evaluation by Navistar 5.4 Submission The material and test report shall be submitted to: Materials Engineering, Navistar

32、Inc., 10400 W. North Ave, Melrose Park, IL 60160. 5.5 Approval A report from Navistar will be issued, approving material to this specification. Approval is not formally granted until this report has been published. A change to this specification listing the new approval may be delayed. The approval

33、report serves as authorization for the use of that system prior to the changes to this specification. 6.0 QUALIFICATION Engineering qualification of sources is required in advance of production shipments. Samples shall be accompanied by test data certifying that all requirements of the specification

34、 have been met. Suppliers shall submit samples for approval of finish, luster, color and appearance to the Navistar Industrial Design Group. Upon approval, styling master samples denoting the minimum level of acceptable appearance quality shall be developed and retained by the supplier and the quali

35、ty department of each using NAVISTAR facility. 6.1 Quality Control Plan A Quality Control Plan for products supplied to the requirements of this specification will be established by mutual agreement between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics,

36、 where applicable*, shall be included in the plan as features for management by statistical process control.* * Other characteristics for inclusion in the control plan may be specified on the engineering drawing and/or purchase order. * See NAVISTAR Engineering Design Standard A-16 7.0 SOURCE APPROV

37、AL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation an

38、d approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Corporate Buyer upon request. 7.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent

39、 in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplie

40、r shall notify NAVISTAR Materials Engineering and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and Paint film thickness as per ASTM D1186 Adhesion of paint as per GT-Paint method 5A NUMBER: MP

41、APS G-6046 TITLE: Elastomeric Coatings REVISION: 1606 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 5 of 8 new or

42、 amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 7.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guideli

43、nes, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on sp

44、ecific products. 8.0 SHIPPING AND HANDLING Shipping and identification shall be in accordance with NAVISTAR Manufacturing Standard MS-D-13. Parts shall be packaged so as to avoid any damage in shipment detrimental to the appearance of the part. 9.0 DESIGNATION ON DRAWINGS Example of note to use on d

45、rawings: Coat per MPAPS G-6046 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Pa

46、rk, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ NUMBER: MPAPS G-6046 TITLE: Elastomeric Coatings REVISION: 1606 This document is restricted and may not be sent outside Navistar, I

47、nc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 6 of 8 TABLE 1 FILM PERFORMANCE REQUIREMENTS Test* Test Method Requirements Adhesion(1) GT-Paint, method 5A Steps 2,3,4 & 5 Under Proc

48、edure 95% Min. Peel per ASTM D903, kN/m 5 Min. Accelerated Adhesion (Water immersion, 49C) GT-Paint, method 5C Steps 2,3,4,5,6 & 7 Under Procedure 95% Min. Same as above except Peel per ASTM D903, kN/m and 168 hr immersion 4.5 Min. Initial Gloss GT-Paint, method 6B Step 3 Under Procedure Shall Match

49、 Color Standard in the Navistar Styling Department Intercoat Adhesion GT-Paint, method 5B 95% Min. Color(1) Visual comparison Shall Match Color Standard in the Navistar Styling Department Mar Resistance(1) GT-Paint, method 12 Steps 4.1 to 4.4 Under Procedure No Nail Marks Visible To The Unaided Eye Gravelometer SAE J400 2A as