NASA UFGS-12 31 00-2009 MANUFACTURED METAL CASEWORK《制造的金属箱子》.pdf

《NASA UFGS-12 31 00-2009 MANUFACTURED METAL CASEWORK《制造的金属箱子》.pdf》由会员分享，可在线阅读，更多相关《NASA UFGS-12 31 00-2009 MANUFACTURED METAL CASEWORK《制造的金属箱子》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-12 31 00 (May 2009)-Preparing Activity: NASA SupersedingUFGS-12 31 00 (January 2008)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2009*SECTION TABLE OF CONTENTSDIVISION 12 - FURNISHINGSSECTION 12 31 00MANUFACTURED METAL

2、CASEWORK05/09PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 DELIVERY, STORAGE, AND HANDLING1.4 DESIGNPART 2 PRODUCTS2.1 GENERAL2.2 MATERIALS2.3 STEEL CABINET FABRICATION2.3.1 General2.3.2 Workmanship2.3.3 Minimum Thickness of Steel2.3.4 Cabinets2.3.5 Doors2.3.6 Drawers2.3.7 Shelves2.3.8 Dustcover Top

3、s2.3.9 Finish2.3.10 Welded Cabinets2.3.11 Doors and Drawer Fronts2.3.12 Undercounter Table and Bench Frames2.3.13 Closures and Filler Strips at Pipe Spaces2.4 MISCELLANEOUS CABINETS2.4.1 Combination Sink-and-Base Cabinet2.4.2 Special Purpose Cabinets2.5 ACCESSORIES AND HARDWARE2.6 CABINETS2.6.1 Cabi

4、net Locks2.6.2 Cabinet Hardware2.7 FINISH2.7.1 Cabinet Finish2.8 COLOR, TEXTURE, AND PATTERN2.9 DISPENSING TRAYS AND BINSSECTION 12 31 00 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.10 ELECTRICAL FIXTURES2.11 SUSPENSION SYSTEM FOR INTERCH

5、ANGEABLE CASEWORK2.12 WHEELED CARRIERPART 3 EXECUTION3.1 INSTALLATION3.1.1 Coordination3.1.2 Fastenings and Anchorage3.1.3 Closures and Filler Plates3.1.4 Cabinets3.2 CLEANING3.3 INSPECTION- End of Section Table of Contents -SECTION 12 31 00 Page 2Provided by IHSNot for ResaleNo reproduction or netw

6、orking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-12 31 00 (May 2009)-Preparing Activity: NASA SupersedingUFGS-12 31 00 (January 2008)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2009*SECTION 12 31 00MANUFACTURED METAL CASE

7、WORK05/09*NOTE: This guide specification covers the requirements for metal casework.Coordinate the use of this section in conjunction with and coordinated with the referenced sections.Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed

8、 items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments and suggestions on this guide specification are welcome and should be directed to the technical proponent of the s

9、pecification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications

10、cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Artic

11、le to automatically place the reference in the Reference Article. Also use the SECTION 12 31 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Reference Wizards Check Reference feature to update the issue dates.References not used in the text

12、will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic d

13、esignation only.AMERICAN WELDING SOCIETY (AWS)AWS D1.1/D1.1M (2008; Errata 2009) Structural Welding Code - SteelAWS D1.3/D1.3M (2008; Errata 2008) Structural Welding Code - Sheet SteelASTM INTERNATIONAL (ASTM)ASTM A 1008/A 1008M (2008a) Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, S

14、tructural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake HardenedASTM A 167 (1999; R 2004) Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripASTM A 325 (2009) Standard Specification for St

15、ructural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile StrengthASTM A 325M (2009) Standard Specification for Structural Bolts, Steel, Heat Treated, 830 Mpa Minimum Tensile Strength (Metric)ASTM C 1036 (2006) Standard Specification for Flat GlassASTM D 4689 (1999; R 2005) Standard Specifica

16、tion for Adhesive, Casein-TypeASTM D 4690 (1999; R 2005) Standard Specification for Urea Formaldehyde Resin AdhesivesASTM F 594 (2008) Standard Specification for Stainless Steel NutsASTM F 836M (2002) Standard Specification for Style 1 Stainless Steel Metric NutsSECTION 12 31 00 Page 4Provided by IH

17、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BUILDERS HARDWARE MANUFACTURERS ASSOCIATION (BHMA)BHMA A156.11 (2004) American National Standard for Cabinet LocksBHMA A156.5 (2001) Auxiliary Locks Supplement 2007) International Plumbing CodeKITCHEN CABINET MANUFAC

18、TURERS ASSOCIATION (KCMA)KCMA A161.1 (2000) Performance Nail, Expansion; and Nail, Drive Screw (Devices, Anchoring, Masonry)FS TT-C-490 (1990; Am 2) Cleaning Methods for Ferrous Surfaces and Pretreatments for Organic CoatingsFS TT-E-489 (Rev J; Notice 1) Enamel, Alkyd, Glass, Low VOC ContentFS TT-E-

19、491 (Rev C) Enamel; Gloss, Synthetic (for Metal and Wood Furniture)FS TT-F-336 (Rev E) Filler, Wood, PasteFS WW-P-541 (1990e; Am 1) Plumbing FixturesSECTION 12 31 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1.2 SUBMITTALS*NOTE: Review Su

20、bmittal Description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submit

21、tal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the

22、 project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect

23、-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item

24、for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation foll

25、owing the “G“ designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsSubmit fabrication drawings for steel and wood cabinets.Submit Installation Drawings for steel and wood

26、cabinets in accordance with the paragraph entitled, “Installation,“ of this section.SD-03 Product DataSubmit Manufacturers catalog data for the following items:CabinetsCorrosion-Resistant SteelGlassAdhesivesFiller MaterialSECTION 12 31 00 Page 6Provided by IHSNot for ResaleNo reproduction or network

27、ing permitted without license from IHS-,-,-FastenersSteel SinksService FixturesAccessories and HardwarePlastic LaminateCountertopsSD-04 SamplesAccessories and Hardware, one each.Submit Manufacturers Standard Color Charts in accordance with paragraph entitled, “General,“ of this section.SD-07 Certifi

28、catesSubmit certificates for the following items showing conformance with the referenced standards contained in this section.Corrosion-Resistant SteelGlassAdhesivesFiller MaterialFastenersSteel SinksService FixturesAccessories and HardwareSD-08 Manufacturers InstructionsSubmit Manufacturers Instruct

29、ions for in accordance with paragraph entitled, “General,“ of this section.1.3 DELIVERY, STORAGE, AND HANDLINGDeliver, store, and handle metal casework in a manner that prevents damage or disfigurement.Provide temporary skids under units weighing more than _ kilogram pounds.1.4 DESIGNProvide metal c

30、asework, factory-fabricated and finished in the manufacturers standard sizes and finishes of the type, design, and configuration indicated. Construct casework as specified and meet the requirements of KCMA A161.1. Provide wall and base cabinet assemblies consisting of individual units joined into co

31、ntinuous sections. Accomplish fastenings to permit removal and replacement of individual units without affecting the remainder of the installation. Provide counters with watertight sink rim when indicated. Provide removable doors equipped with position stops to avoid accidental complete withdrawals.

32、 Fix or adjust shelves as indicated.PART 2 PRODUCTS2.1 GENERALSubmit Manufacturers Standard Color Charts for metal cabinets showing the SECTION 12 31 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-manufacturers recommended color and finish

33、selections.Submit Manufacturers Instructions for metal cabinet systems including special provisions required to install equipment components and system packages. Include special notices detailing impedances, hazards and safety precautions.Provide the manufacturers standard size and type of casework

34、conforming with the design indicated. type and design indicated. Provide both wall and base cabinet assemblies consisting of individual units joined into continuous sections as indicated. Accomplish fastenings to permit removal and replacement of individual units without affecting the remainder of t

35、he installation.2.2 MATERIALSProvide Corrosion-Resistant Steel conforming to ASTM A 1008/A 1008M, and ASTM A 167, Type 302 304 316 Finish 4.Provide Glass conforming to ASTM C 1036, Type I, Class 1, Quality q3, 6 millimeter 1/4 inch thick, for unframed sliding glass doors; other glass is to conform t

36、o ASTM C 1036, Type II, Class 1, Quality q8, 5 millimeter 7/32 inch thick.Use thermosetting urea-resin Type II Adhesives for application of plastic laminate conforming to ASTM D 4690 as recommended by the manufacturer of the laminate. Use adhesive conforming to ASTM D 4689 for wood members.Provide f

37、iller material conforming to FS TT-F-336.*NOTE: Review NEMA LD 3 and insert style, type, grade, class, and finish as required.*Provide Plastic Laminate conforming to NEMA LD 3, Style _, Type _, Grade _, Class _, Finish _.Provide Accessories and Hardware conforming to the following requirements, as a

38、pplicable:Extension drawer slides: BHMA A156.9, Type B85071 Semiconcealed hinges: BHMA A156.9, Type B81201, 40 millimeter 1-1/2 inches Full surface hinges: BHMA A156.9, Type B81131, 40 millimeter 1-1/2 inches Knob pulls: BHMA A156.9, 25 millimeter 1-inch diameter, Type B12132 Bar type pulls: BHMA A1

39、56.9, 100 millimeter 4-inch overall length, Type B12012Locks, keying, and keys: As directedCatches: Magnetic, 22 Newton 5-pound pullSECTION 12 31 00 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Sliding door set:Impregnated fiberboard trackNy

40、lon glidesProvide Fasteners conforming to the following:Screws: Complying with ANSI Standards, Group, Type and Class as applicableAnchoring Devices: FS FF-S-325, Group, Type, and Class as applicableToggle bolts: FS FF-B-588, Type I, Class A, Style 2Nuts: ASTM F 594, corrosion-resistant steelBolts: A

41、STM A 325, heavy, hexagon head bolts corrosion-resistant steelNuts: ASTM F 836M, corrosion-resistant steelBolts: ASTM A 325M, heavy, hexagon head bolts corrosion-resistant steel*NOTE: Sink for inset-type installation is as specified in Section 22 00 00 PLUMBING, GENERAL PURPOSE.*Corrosion-resistant

42、Steel Sinks:1.3 millimeter 18-gauge corrosion-resistant steel, integral with corrosion-resistant steel countertop1.3 millimeter 18-gauge corrosion-resistant steel, nonintegral, self-rimmingDrain holes in center of bowlUnderside coated with 3 millimeter 1/8-inch thick sound deadenerDie-form, seamless

43、, raised edges at front and endsCove corners to 13 millimeter 1/2-inch radiusEquip with strainers and tail piecesProvide Service Fixtures conforming to the following requirements:a. Provide fixtures in accordance with the water conservation policy as stated in the ICC IPC.b. Faucets:(1) Splashback m

44、ounted, cast brass, chrome plated, FS WW-P-541(2) Deck mounted, cast brass, chrome plated, FS WW-P-541c. Gas, air, and vacuum, distilled water, steam, and de-ionized water SECTION 12 31 00 Page 9Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-cocks: cast brass, chrome plated, ground key typed. Drains, strainers, and taps: brass, chrome plated, FS WW-P-541e. Index buttons: plastic, color codes in accordance with SEFA 7f. Special items: provide nipples and locknuts with each fixture.*