NASA NACA-TN-1817-1949 Plastic buckling of simply supported compressed plates《简支压缩板的塑性屈曲》.pdf
《NASA NACA-TN-1817-1949 Plastic buckling of simply supported compressed plates《简支压缩板的塑性屈曲》.pdf》由会员分享,可在线阅读,更多相关《NASA NACA-TN-1817-1949 Plastic buckling of simply supported compressed plates《简支压缩板的塑性屈曲》.pdf(23页珍藏版)》请在麦多课文档分享上搜索。
1、. r -I * . : .- . NATIONAL, ADVISORY COMMITTEE FOR AERONAUTICS TECHNICAL NOTE No. 1817 PLASTIC BUCKLING OF SIMPLY SUPPORTED COMPRJZSSED PLATES By Richard A. Pride and George J. Heimerl Langley Aeronautical Laboratory Langley Air Force Base, Va. Provided by IHSNot for ResaleNo reproduction or network
2、ing permitted without license from IHS-,-,-I!U!l?IONAT; ADVISORY Cm TECHNTCAL NOTE NO. 1817 By Richard A. Pride end George J. Helmerl An Fnvestigation was made to asaertain the validity of various theories for the plastic buckling of use of-inside dimenBiOn6 is consistent with previous method for di
3、mensioning extrudons (refer- ence 4) and gives best agreement with test results in elas- tic range length of platy thickness of plate plate bu number by which criticel stress computed for elastic case must be multi$lied to give criti- cal stress for plastic case (for stresses In elastic range, tl =
4、1, whereas above elastic renge, Q * DIL2 = 1 - c8(2 - P)(W - 1) D* = T.- c6(2p - 1* 7 (6) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 secanmodtilus method. - An empirical method fordetermlning plastic buckling streseee of plates was suggested b
5、y Gerard (reference 10) and has been found to-work qtite well for plate assemblies of H-, Z-, and C-sec- tlans for a number of aircraft structural materials. (See reference 4.) This method defines q *aa *a =- E (71 The results of the local-Instability tests are summarized for the critical. compressi
6、ve stress Jn table I and figure 6 and for the average stress at maximum load in table I. The correlation of the results with the theories for plastic buckljng and the secant-modulus method is shown Fn figure 9. For direct comparisan.with the applicable stress-strain curves for the materl$l, the expe
7、rimsntal critical compressive stress ucr is plot- ted against the calculated elastic critical compressive atraW Gcr (see equation (2) in figure 6 where the teat points are seem to fall saamwhat below the atrese-strain curves in the plastic region. The generalized correlation with the single represen
8、tative compressive etress-strain curve, the theories for plastic buckling, and the eecant- modulus method is madein figure 9 by adjusting the test-results to allow for variations in the compressive yield stress of the material for the various tubes by the method described in reference ll. In this ge
9、neralized comparison the test results In the plastic region can be seen to fall a little below the stress-strain curve which also gives the results of the secant-modulus method; the test results lie closeat to the calculated plate buckling curve ncr aWnat- 6cr given by Stowelle theory. Tlyuahins and
10、 Bijlsards theories give results which are slightly higher but st3Jl fall below the comreasive stress-strain curve. Thus, good agreement with the test-results is shown for the three deformation-type theories of plastic buckling. There is little correlation, however, between the test- results and the
11、 Handelman-%ager theory, and the difference between this flow-type theory and deformation-type theories is marked. (See fig. 9.) With regard to the accuracy of the teat results for ucrr the nearly ideal load-displacement curves obtained for many of the tests (fig* 4) end the unusual degree of isotro
12、py of the mteriel (fig. 7) lead to the belief that the teat specimens came close to being theoretically ideal specimens, and therefore the test-results provide a good basis for dls- criminating between the various theories on plastic buckling of plates. Provided by IHSNot for ResaleNo reproduction o
13、r networking permitted without license from IHS-,-,-NACA TN NO. 1817 CONCLUSIONS 9 The result8 of the local-instability tests of drawn spume tubes warrant the following concluaione a8 regasde the plastic buckling of a long, flat, eimply supported ccmeeeed plate: 1. The result6 of these test6 show go
14、od agreement with Stowelle theory for the plastic buckling of a simply supported plate which ie based on a deformatirm theory of plastioity. This confirmation, together with that previously shown for a flauge aud column, is considered to constitute a satisfactory experimental verification of the the
15、ory. 2. Good agreement with the teat resulte Is evidenced in general by the deformation-type theories for plastic buckling. Stowells theory is in the closest agreerrmnt with the teat results reported herein, but Ilyushins and Bijlaarde theories give results only slightly higher. 3. Wked disagreement
16、 is shown between the test results and the Handem-Prager theory which is based on a flow theory of plasticity. 4. Buckling stresses calculated by the empirical secant-modulus vsthod, are reasonable, though higher than the test results. This convenient rapid method can therefore be used for au approx
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NASANACATN18171949PLASTICBUCKLINGOFSIMPLYSUPPORTEDCOMPRESSEDPLATES 压缩 塑性 屈曲 PDF

链接地址:http://www.mydoc123.com/p-836244.html