MSS SP-72A-2010 Ball Valves with Flanged or Butt-Welding Ends for General Service.pdf

《MSS SP-72A-2010 Ball Valves with Flanged or Butt-Welding Ends for General Service.pdf》由会员分享，可在线阅读，更多相关《MSS SP-72A-2010 Ball Valves with Flanged or Butt-Welding Ends for General Service.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 MSS SP-72-2010a MSS Ball Valves with Flanged or Butt-Welding Ends for General Service Standard Practice Developed and Approved by the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 127 Park Street, NE Vienna, Virginia 22180 Phone: (703) 281-6613 Fax: (703) 281-6671 E

2、-mail: standardsmss-hq.org www.mss-hq.org Note: This 2010a Edition Replaces the Original 2010 Edition. MSS STANDARD PRACTICE SP-72 i This MSS Standard Practice was developed under the consensus of the MSS Technical Committee 401 and the MSS Coordinating Committee. The content of this Standard Practi

3、ce is the resulting efforts of competent and experienced volunteers to provide an effective, clear, and non-exclusive standard that will benefit the industry as a whole. This MSS Standard Practice describes minimal requirements and is intended as a basis for common practice by the manufacturer, the

4、user, and the general public. The existence of an MSS Standard Practice does not in itself preclude the manufacture, sale, or use of products not conforming to the Standard Practice. Mandatory conformance to this Standard Practice is established only by reference in other documents such as a code, s

5、pecification, sales contract, or public law, as applicable. MSS has no power, nor does it undertake, to enforce or certify compliance with this document. Any certification or other statement of compliance with the requirements of this Standard Practice shall not be attributable to MSS and is solely

6、the responsibility of the certifier or maker of the statement. “Unless indicated otherwise within this MSS Standard Practice, other standards documents referenced to herein are identified by the date of issue that was applicable to this Standard Practice at the date of approval of this MSS Standard

7、Practice (see Annex A). This Standard Practice shall remain silent on the validity of those other standards of prior or subsequent dates of issue even though applicable provisions may not have changed.” By publication of this Standard Practice, no position is taken with respect to the validity of an

8、y potential claim(s) or of any patent rights in connection therewith. MSS shall not be held responsible for identifying any patent rights. Users are expressly advised that determination of patent rights and the risk of infringement of such rights are entirely their responsibility. In this Standard P

9、ractice, all text, notes, annexes, tables, figures, and references are construed to be essential to the understanding of the message of the standard, and are considered normative unless indicated as “supplemental”. All appendices, if included, that appear in this document are construed as “supplemen

10、tal”. Note that supplemental information does not include mandatory requirements. U.S. customary units in this Standard Practice are the standard; (SI) metric units are for reference only. Substantive changes identified in the 2010 edition are “flagged” by parallel bars, as shown on the margins of t

11、his paragraph, and included within this 2010a edition. The specific detail of the change may be determined by comparing the material flagged with that in the previous edition. Specific changes and corrections between the 2010 and 2010a editions are indicated in the Forward. Non-toleranced dimensions

12、 in this Standard Practice are nominal unless otherwise specified. Excerpts of this Standard Practice may be quoted with permission. Credit lines should read Extracted from MSS SP-72-2010a with permission of the publisher, Manufacturers Standardization Society of the Valve and Fittings Industry. Rep

13、roduction and/or electronic transmission or dissemination is prohibited under copyright convention unless written permission is granted by the Manufacturers Standardization Society of the Valve and Fittings Industry Inc. All rights reserved. MSS is a registered trademark of Manufacturers Standardiza

14、tion Society of the Valve and Fittings Industry, Inc. Originally Published: February 1970 2010 Version Approved: March 2010 2010 Version Published: April 2010 2010a Version Published: April 2012 Copyright , 2010/2011 by Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. P

15、rinted in U.S.A. MSS STANDARD PRACTICE SP-72 ii FOREWORD The 1999 Edition of MSS SP-72 was updated from the 1992 Edition by revising material names in Sections 1.4, 2.1.5., 2.1.6, and 4.1. Metric data (DN) and (PN) was added to Sections 1.3, 3.1.1, 5.2.2.1, 7.1.3, 7.1.4, 7.2.2, 7.2.3, and Table 1. T

16、he formulas in Sections 7.1.4 and 7.2.2 was revised to agree with MSS IS-9 formatting. The reference to NPS was corrected in all applicable Sections. Annex A listing all referenced standards documents was added. The 2010 Edition of MSS SP-72 was substantively updated from the 1999 Edition by primari

17、ly revising material in Section 7.2.4. The Pressure Number “PN” reference data was deleted in the 2010 edition (Sections 5.2.2.1, 5.2.2.2, and 7.1.4) as ASME no longer makes a soft conversion between class designations and PN. In addition, the Annex A listing of all referenced standards documents ha

18、s been updated. This 2010a Edition of MSS SP-72 replaces the 2010 Edition. The 2010a Edition of MSS SP-72 updates the obsolete 2010 Edition by: (1) the re-inclusion (from previous editions) of Section 3.1.2 and the first sentence of Section 5.3.1; (2) additional descriptive notes were inserted in Se

19、ctions 7.1.4 and 7.2.2; (3) the equation in Section 7.2.4.3 was clarified; (4) corrected the definition of “MYS1” in Section 7.1.4 and “AYS2” in Section 7.1.4; (5) corrected the definition of “AYS5” and “AYS6” in Section 7.2.2; and (6) additional editorial and conforming corrections. The corrections

20、 and changes mentioned in this paragraph are not “flagged” in the body of this text in order to preserve the substantive changes from the 1999 Edition that were identified in the original 2010 Edition. MSS STANDARD PRACTICE SP-72 iii TABLE OF CONTENTS SECTION PAGE 1 SCOPE . 1 2 SERVICE PRESSURE RATI

21、NGS . . 1 3 VALVE PORT SIZES . 1 4 MATERIALS . 2 5 DESIGN . 2 6 MARKING . 2 7 TESTING . 3 TABLE 1 Port Sizes for Less than Full Port Ball Valves . 5 FIGURE 1 Examples of Body Construction 6 2 Nomenclature for Ball Valve Parts, Typical 7 ANNEX A Referenced Standards and Applicable Dates . 8 MSS STAND

22、ARD PRACTICE SP-72 1 1. SCOPE 1.1 This Standard Practice covers flanged or Butt-weld end ball valves having in general, but not restricted to, round openings which may be full port, regular port, or reduced port types. The following characteristics shall be considered standard practice unless otherw

23、ise specified by agreement between manufacturer and purchaser. 1.2 Valves covered by this Standard Practice are suitable for use in general liquid and gas service. Their service pressures and temperatures generally conform to standards cited in Section 2, but may be restricted by the materials used

24、for their seats and seals, or by other special considerations. 1.3 The size range covered by this Standard Practice is NPS 1/2 (DN 15) through NPS 36 (DN 900). 1.4 This Standard Practice covers ball valves of the following materials: Carbon Steel Alloy Steels Stainless Steels Ductile Iron Gray Iron

25、Copper Alloy 1.5 Names of common valve body types are given in Figure 1. When variations or other body types are used, they may be named by the manufacturer. The names of basic valve parts are given in Figure 2. Other parts may be named by the manufacturer. Body types and valve parts may also be ide

26、ntified by applicable MSS or other terminology standards. 2. SERVICE PRESSURE RATINGS 2.1 The pressure-temperature rating of flanged and Butt-welding end ball valves shall conform to those set forth in the Standards listed within this section, except as they are limited by their seat and seal materi

27、als. 2.1.1 Carbon Steel ASME B16.5 ANSI/ASME B16.1-2005 Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 B16.5-2009 Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard B16.10-2009 Face-to-Face and End-to-End Dimensions of Valves B16.24-2006 Cast Copper

28、 Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 600, 900, 1500, and 2500 B16.34-2009 Valves Flanged, Threaded and Welding End B16.42-1998 Ductile Iron Pipe Flanges and Flanged Fittings: Classes 150 and 300 MSS SP-25-2008 Standard Marking System for Valves, Fittings, Flanges, and Unions S

29、P-44-2010 Steel Pipeline Flanges; including Errata (2011) The following organizations appear in the above list: ANSI American National Standards Institute, Inc. 25 West 43rd Street, Fourth Floor New York, NY 10036-7406 ASME American Society of Mechanical Engineers (ASME International) Three Park Ave

30、nue New York, NY 10016-5990 MSS Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 127 Park Street, NE Vienna, VA 22180-4602 Listing of MSS Standard Practices TITLE SP-6-2012 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fitt

31、ings SP-9-2008 Spot Facing for Bronze, Iron and Steel Flanges SP-25-2008 Standard Marking System for Valves, Fittings, Flanges, and Unions SP-42-2009 Corrosion Resistant Gate, Globe, Angle and Check Valves with Flanged and Butt Weld Ends (Classes 150, 300 & 600) SP-43-2008 Wrought and Fabricated But

32、t-Welding Fittings for Low Pressure, Corrosion Resistant Applications (Incl. 2010 Errata Sheet) SP-44-2010 Steel Pipeline Flanges (incl. 2011 Errata Sheet) SP-45-2003 (R 2008) Bypass and Drain Connections SP-51-2007 Class 150LW Corrosion Resistant Flanges and Cast Flanged Fittings SP-53-1999 (R 2007

33、) Quality Standard for Steel Castings and Forgings for Valves, Flanges, and Fittings and Other Piping Components Magnetic Particle Examination Method SP-54-1999 (R 2007) Quality Standard for Steel Castings and Forgings for Valves, Flanges, and Fittings and Other Piping Components Radiographic Examin

34、ation Method SP-55-2011 Quality Standard for Steel Castings for Valves, Flanges, Fittings, and Other Piping Components Visual Method for Evaluation of Surface Irregularities (ANSI-approved American National Standard) SP-58-2009 Pipe Hangers and Supports Materials, Design, Manufacture, Selection, App

35、lication, and Installation (incorporates content of SP-69, 77, 89, and 90) (ANSI-approved American National Standard) SP-60-2004 Connecting Flange Joint between Tapping Sleeves and Tapping Valves SP-61-2009 Pressure Testing of Valves SP-65-2008 High Pressure Chemical Industry Flanges and Threaded St

36、ubs for Use with Lens Gaskets SP-67-2011 Butterfly Valves SP-68-2011 High Pressure Butterfly Valves with Offset Design SP-69-2003 Pipe Hangers and Supports Selection and Application (ANSI-approved American National Standard) SP-70-2011 Gray Iron Gate Valves, Flanged and Threaded Ends SP-71-2011 Gray

37、 Iron Swing Check Valves, Flanged and Threaded Ends SP-72-2010a Ball Valves with Flanged or Butt-Welding Ends for General Service SP-75-2008 Specification for High-Test, Wrought, Butt-Welding Fittings SP-78-2011 Gray Iron Plug Valves, Flanged and Threaded Ends SP-79-2011 Socket Welding Reducer Inser

38、ts SP-80-2008 Bronze Gate, Globe, Angle, and Check Valves SP-81-2006a Stainless Steel, Bonnetless, Flanged Knife Gate Valves SP-83-2006 Class 3000 Steel Pipe Unions Socket Welding and Threaded SP-85-2011 Gray Iron Globe & Angle Valves, Flanged and Threaded Ends SP-86-2009 Guidelines for Metric Data

39、in Standards for Valves, Flanges, Fittings, and Actuators (Incl. 2011 Errata Sheet) SP-87-1991 (R 1996 Reinstated 2011) Factory-Made Butt-Welding Fittings for Class I Nuclear Piping Applications SP-88-2010 Diaphragm Valves SP-91-2009 Guidelines for Manual Operation of Valves SP-92-2012 MSS Valve Use

40、r Guide SP-93-2008 Quality Standard for Steel Castings and Forgings for Valves, Flanges, Fittings, and Other Piping Components Liquid Penetrant Examination Method SP-94-2008 Quality Standard for Ferritic and Martensitic Steel Castings for Valves, Flanges, Fittings, and Other Piping Components Ultras

41、onic Examination Method SP-95-2006 Swage(d) Nipples and Bull Plugs SP-96-2011 Guidelines on Terminology for Valves and Fittings SP-97-2012 Integrally Reinforced Forged Branch Outlet Fittings Socket Welding, Threaded, and Buttwelding Ends SP-98-2012 Protective Coatings for the Interior of Valves, Hyd

42、rants, and Fittings SP-99-2010 Instrument Valves SP-100-2009 Qualification Requirements for Elastomer Diaphragms for Nuclear Service Diaphragm Valves SP-101-1989 (R 2001) Part-Turn Valve Actuator Attachment Flange and Driving Component Dimensions and Performance Characteristics SP-102-1989 (R 2001)

43、Multi-Turn Valve Actuator Attachment Flange and Driving Component Dimensions and Performance Characteristics SP-104-2012 Wrought Copper Solder-Joint Pressure Fittings SP-105-2010 Instrument Valves for Code Applications SP-106-2012 Cast Copper Alloy Flanges and Flanged Fittings: Class 125, 150, and 3

44、00 SP-108-2012 Resilient-Seated Cast Iron Eccentric Plug Valves SP-109-2012 (R 2006) Welded Fabricated Copper Solder Joint Pressure Fittings SP-110-2010 Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends (incl. 2010 Errata Sheet) SP-111-2001 (R 2005) Gray-Iron and Ductile-Ir

45、on Tapping Sleeves SP-112-2010 Quality Standard for Evaluation of Cast Surface Finishes Visual and Tactile Method. This SP must be used with a 10-surface, three dimensional Cast Surface Comparator, which is a necessary part of the standard. Additional Comparators available separately. SP-113-2001 (R

46、 2007) Connecting Joint between Tapping Machines and Tapping Valves SP-114-2007 Corrosion Resistant Pipe Fittings Threaded and Socket Welding Class 150 and 1000 (ANSI-approved American National Standard) SP-115-2010 Excess Flow Valves, 1 NPS and Smaller, for Fuel Gas Service SP-116-2011 Service-Line

47、 Valves and Fittings for Drinking Water Systems SP-117-2011 Bellows Seals for Globe and Gate Valves SP-118-2007 Compact Steel Globe & Check Valves Flanged, Flangeless, Threaded & Welding Ends (Chemical & Petroleum Refinery Service) SP-119-2010 Factory-Made Wrought Belled End Pipe Fittings for Socket

48、-Welding SP-120-2011 Flexible Graphite Packing System for Rising Stem Valves Design Requirements SP-121-2006 Qualification Testing Methods for Stem Packing for Rising Stem Steel Valves SP-122-2005 Plastic Industrial Ball Valves SP-123-1998 (R 2006) Non-Ferrous Threaded and Solder-Joint Unions for Us

49、e with Copper Water Tube SP-124-2001 Fabricated Tapping Sleeves SP-125-2010 Gray Iron and Ductile Iron In-Line, Spring-Loaded, Center-Guided Check Valves SP-126-2007 Steel In-Line Spring-Assisted Center Guided Check Valves SP-127-2001 Bracing for Piping Systems Seismic-Wind-Dynamic Design, Selection, Application SP-128-2012 Ductile Iron Gate Valves SP-129-2003 (R 2007) Copper-Nickel Socket-Welding Fittings and Unions SP-130-2003 Bellows Seals for Instrument Valves SP-131-2010 Metallic Manually Operated Gas Distribution Valves SP-132-2010 Co