JEDEC JESD213A-2017 Standard Test Method Utilizing X-Ray Fluorescence (XRF) for Analyzing Component Finishes and Solder Alloys to Determine Tin (Sn) C Lead (Pb) Content.pdf

《JEDEC JESD213A-2017 Standard Test Method Utilizing X-Ray Fluorescence (XRF) for Analyzing Component Finishes and Solder Alloys to Determine Tin (Sn) C Lead (Pb) Content.pdf》由会员分享，可在线阅读，更多相关《JEDEC JESD213A-2017 Standard Test Method Utilizing X-Ray Fluorescence (XRF) for Analyzing Component Finishes and Solder Alloys to Determine Tin (Sn) C Lead (Pb) Content.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、JEDEC STANDARD Standard Test Method Utilizing X-Ray Fluorescence (XRF) for Analyzing Component Finishes and Solder Alloys to Determine Tin (Sn) Lead (Pb) Content JESD213A (Revision of JESD213, March 2010) APRIL 2017 JEDEC SOLID STATE TECHNOLOGY ASSOCIATION NOTICE JEDEC standards and publications con

2、tain material that has been prepared, reviewed, and approved through the JEDEC Board of Directors level and subsequently reviewed and approved by the JEDEC legal counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstandings between manufact

3、urers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or internationally. JEDEC

4、standards and publications are adopted without regard to whether or not their adoption may involve patents or articles, materials, or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the JEDEC standards

5、or publications. The information included in JEDEC standards and publications represents a sound approach to product specification and application, principally from the solid state device manufacturer viewpoint. Within the JEDEC organization there are procedures whereby a JEDEC standard or publicati

6、on may be further processed and ultimately become an ANSI standard. No claims to be in conformance with this standard may be made unless all requirements stated in the standard are met. Inquiries, comments, and suggestions relative to the content of this JEDEC standard or publication should be addre

7、ssed to JEDEC at the address below, or refer to www.jedec.org under Standards and Documents for alternative contact information. Published by JEDEC Solid State Technology Association 2017 3103 North 10th Street Suite 240 South Arlington, VA 22201-2107 This document may be downloaded free of charge;

8、however JEDEC retains the copyright on this material. By downloading this file the individual agrees not to charge for or resell the resulting material. PRICE: Contact JEDEC Printed in the U.S.A. All rights reserved PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by JEDEC and may not be r

9、eproduced without permission. For information, contact: JEDEC Solid State Technology Association 3103 North 10th Street Suite 240 South Arlington, VA 22201-2107 or refer to www.jedec.org under Standards-Documents/Copyright Information. JEDEC Standard No. 213A -i- Standard Test Method Utilizing X-Ray

10、 Fluorescence (XRF) for Analyzing Component Finishes and Solder Alloys to Determine Tin (Sn) Lead (Pb) Content Contents Page Foreword ii 1 Scope 1 2 Normative references 1 3 Terms and definitions 1 4 Apparatus 2 5 Procedure 3 Annex A Instrument capabilities 5 Annex B Differences between revisions 6

11、Figures 1 Example Measurement Zone on Surface Mounted Devices 3 Tables A.1 Typical Instrument Capabilities 5 JEDEC Standard No. 213A -ii- Foreword This document is intended to be used by Original Component Manufacturers who deliver electronic components and Original Equipment Manufacturers who are t

12、he platform system integrators. It is intended to be applied prior to delivery by the OCMs and may be used by OEM system engineers and procuring activities as well as U.S Government Department of Defense system engineers, procuring activities and repair centers. This document was drafted in cooperat

13、ion between JEDEC JC-13 and TechAmerica G-12 committees. This document does not cancel or replace in whole or in part any other standard but was released with the intention that the initially released document and subsequent revisions be referenced by MIL-STD-202, MIL-STD-750 and MIL-STD-883. Releas

14、e and publication of this document constitutes approval by the JEDEC Board of Directors. JEDEC Standard No. 213A Page 1 Standard Test Method Utilizing X-Ray Fluorescence (XRF) for Analyzing Component Finishes and Solder Alloys to Determine Tin (Sn) Lead (Pb) Content (From JEDEC Board Ballot JCB-17-0

15、4, formulated under the cognizance of the JC-13 Committee, Government Liaison.) 1 Scope This Standard establishes the instrumentation, techniques, criteria, and methods to be utilized to quantify the amount of Lead (Pb) in Tin-Lead (Sn-Pb) alloys and electroplated finishes containing at least 3 weig

16、ht percent (wt%) Lead (Pb) using X-Ray Fluorescence (XRF) equipment. 2 Normative references The following normative documents contain provisions that, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to, or revisions of, any of these

17、 publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. M

18、IL-STD-1916, Department of Defense Test Method Standard DoD Preferred Method for Acceptance of a Product. 3 Terms and definitions For the purposes of this standard, the following terms and definitions apply. Alignment: The adjustment of an object in relation with other objects, or a static orientati

19、on of some object or set of objects in relation to others. Focusing: The action of directing rays toward a point where the rays converge. Beam Collimation: The process of restricting and confining an x-ray beam to a given area. Scanning Electron Microscopy-Energy Dispersive Spectroscopy (SEM-EDS): M

20、easures the number of x-rays produced by a solid sample when bombarded by electrons versus the energy of these x-rays. NOTE The EDS technique identifies and quantifies the element constituents of the sample when performed using appropriate standards. Spatial Resolution: The minimum distance between

21、two adjacent features or the minimum size of a feature that can be detected by a remote sensing system. X-Ray Fluorescence (XRF): The process of emissions of characteristic x-rays. NOTE Analysis using x-ray fluorescence is called “X-ray Fluorescence Spectroscopy.“ JEDEC Standard No. 213A Page 2 4 Ap

22、paratus 4.1 XRF Instrumentation The XRF instrument shall be capable of qualitatively identifying the metals present in a complex sample and providing quantitative accuracy sufficient to insure at least 3 wt% Lead (Pb). 4.2 X-Ray Detector The detector resolution shall be sufficient to quantify lead (

23、Pb) with +/- 2 wt% accuracy, in the range from 0 to 10 wt%, in combination with interfering energy lines from elements such as bismuth (Bi). An x-ray tube potential of 40kV or greater shall be used to support the detection of higher energy lines. 4.3 Alignment, Focusing System, and Scanning Capabili

24、ty XRF systems shall have an alignment and focusing system. The alignment and focusing system must provide visual identification of the desired surface being analyzed. A surface scanning capability may be necessary, depending on component size, X-ray beam size, and presence of surface composition ir

25、regularities, to achieve average quantitative composition during scanning of very small surfaces. 4.4 Spatial Resolution The spatial resolution of the instrument must be sufficient to identify the material composition of the area under analysis, excluding adjacent materials. The spatial resolution o

26、f the instrument shall be verified on a periodic basis. This requires an X-ray beam size smaller than the surface analyzed. See Appendix for typical instrument capabilities. 4.5 Positioning Fixtures Positioning fixtures or sample trays shall be made of materials that do not interfere with the accura

27、cy of the analysis, e.g., commercially pure aluminum. 4.6 Verification Standards For tin lead (Sn-Pb) alloys, a tin-lead composition standard with a lead content of 3.0 wt% is required. The values for the standards shall be traceable to values provided by the National Institute of Standards and Tech

28、nology (NIST). If surface finish thickness is a concern, a foil or layered standard consistent with the component design is required. NOTE For guidance on traceability to values for NIST Standard Reference Materials or other certified reference materials, refer to the NIST Policy on Traceability at

29、http:/ts.nist.gov/traceability/. JEDEC Standard No. 213A Page 3 5 Procedure 5.1 Verification The equipment calibration shall be verified at the beginning of each work shift by measuring the Tin Lead (Sn-Pb) verification standard. The result must agree with the assigned value for the verification sta

30、ndard after taking into account the uncertainty of the assigned value and the laboratorys uncertainty (i.e., if a 3.0 wt% Lead (Pb) standard has a tolerance of 10%, the allowable range would be 2.7 wt% to 3.3 wt% Lead (Pb). It may be useful to implement a control chart to monitor this comparison. 5.

31、2 Sampling Plan Sample size shall be a minimum of five (5) components per plating lot, or as specified in a statistically based sampling plan derived from MIL-STD-1916. Each sample shall be measured independently. Testing multiple samples under the X-ray beam at one time is not acceptable. 5.3 Area

32、of Analysis Each area of analysis shall be a minimum of 15 square mils; otherwise, the maximum available area shall be analyzed. Scanning or step-and-repeat measurements may be used to achieve this requirement. The X-ray spot or beam size shall be small enough to remain within the area under test (w

33、ith a recommended guard band approximating the beam diameter). Large areas shall be analyzed in one location to meet accuracy and reproducibility requirements, rather than testing the entire surface (see Figure 1). Figure 1 Example Measurement Zone on Surface Mounted Devices The samples should be me

34、asured on a flat surface, when possible. For non-flat or rounded surfaces, the sample must be measured at the center to prevent extending beyond the sample edge. Caution should be exercised to prevent X-ray beam scatter by measuring on non-flat surfaces. JEDEC Standard No. 213A Page 4 5.4 Measuremen

35、t Quantity and Location Each visually identifiable component metal surface requires a separate measurement; for example, metal device leads, cans, and lids all require individual analysis. If the sample surface is visually heterogeneous at 30X magnification or less, each visually distinct surface re

36、quires a separate analysis; otherwise, one area per sample is sufficient. Leaded devices shall be measured as closely as practical to the device body, with care to exclude the body material. A second location away from the device body shall also be measured. Devices with varied geometry shall be mea

37、sured at each different plane. The testing facility shall determine the number of spot location measurements required per sample to ensure a high level of confidence is obtained. This determination shall be based upon the equipment used for testing, manufacturing processes, materials used, and geome

38、try of the component being tested. 5.5 Acceptance Criteria The lot shall pass if each of the measured readings are 3.0 wt% Lead (Pb) unless otherwise specified in the contract or acquisition document. These minimums shall be adjusted to account for the overall uncertainty of the measurement, establi

39、shed per a Gauge Reproducibility and Repeatability study (i.e., if the equipment has an established accuracy of 20%, the required minimum is 3.6 wt% Lead (Pb). One rejected sample shall be cause of rejection for the entire sample lot. A failed lot shall remain rejected, or be reworked, or be evaluat

40、ed per 5.6. 5.6 Alternate Acceptance Method Alternate acceptance of the XRF analysis may be conducted using SEM-EDS when the Pb content fails minimum requirements by XRF analysis per 5.5, or segregation of the Lead (Pb) and Tin (Sn) is suspected. 5.6.1 The SEM-EDS equipment calibration shall be veri

41、fied by measuring the Tin Lead (Sn-Pb) verification standard prior to use. 5.6.2 Cross-section is recommended if segregation of Lead (Pb) and Tin (Sn) is suspected. Because SEM-EDS does not penetrate as deeply as XRF, measurements shall be taken at the solder surface, in the middle of the cross-sect

42、ion, and at the interface with the substrate. Samples confirmed by SEM-EDS to have 3.0 wt% Pb (Lead) at any measurement location shall be considered rejections. JEDEC Standard No. 213A Page 5 Annex A (normative) Instrument Capabilities Table A.1 Typical Instrument Capabilities Beam Collimation X-ray

43、 Beam Size Sample Area Typical Samples Limitations Capillary Optic (SEM Mounted X-ray detector) 2 mil (50 m)* 6 sq. mil (0.004 sq. mm) to 50 sq. mil (0.032 sq. mm) Chip components, fine wire, round leaded devices Rounded or irregular surfaces that change height more than 10 mils (250 m) relative to

44、a line tangent to the highest pointCapillary Optic (Benchtop XRF) 3 mil (80 m) 15 sq. mil (0.009 sq. mm) to 200 sq. mil (0.13 sq. mm) Chip components, fine wire, round leaded devices Rounded or irregular surfaces that change height more than 10 mils (250 m) relative to a line tangent to the highest

45、pointMechanical Slot (Benchtop XRF) 8 mil (203 m) 128 sq. mil (0.083 sq. mm) to 0.25 sq. inch (1.6 sq. cm) SMT diodes, Ribbon leaded components, wire and cable, hardware Size limited Mechanical Slot (Handheld XRF) About 400 mil (1 mm to 10 mm) As small as 0.25 sq. inch (1.6 sq. cm.) Fasteners and ha

46、rdware Size limited NOTE Proportional counters may not be able to distinguish between elements with interfering energy lines such as Pb and Bi. A peltier cooled pin diode detector or detector providing increased resolution may be required to achieve this. * In this case, the primary beam is an elect

47、ron beam, not an X-ray beam. JEDEC Standard No. 213A Page 6 Annex B (informative) Differences between JESD213A and JESD213 This annex briefly describes most of the changes made to entries that appear in this standard, JESD213A, compared to its predecessor, JESD213 (March 2010). If the change to a co

48、ncept involves any words added or deleted (excluding deletion of accidentally repeated words), it is included. Some punctuation changes are not included. Clause Description of change 4.2 Removed 2ndsentence: “Note, proportional counter detectors may not be able to meet this requirement, a peltier co

49、oled pin diode detector or detector providing increased resolution may be required to achieve this.” 4.2 Remove 3rdsentence: “The excitation voltage for the X-rays shall be a minimum of 40 KeV to support detection of higher energy lines.”, replaced with new version. 4.3 Removed last sentence: “When scanning capability is not utilized or available, the mean value of at least 5 measurements, using randomly selected locations, where sigma is the standard deviation of those 5 measurements, shall be evaluated using the acceptance criteria in 5.5.” 4.5 Removed subcla