ITU-T V 58-1994 Management Information Model for V-Series DCE-S - Data Communication over the Telephone Network《V系列 DCE 的管理信息模式-电话网络上的数据交流 第14研究组 第65页》.pdf

《ITU-T V 58-1994 Management Information Model for V-Series DCE-S - Data Communication over the Telephone Network《V系列 DCE 的管理信息模式-电话网络上的数据交流 第14研究组 第65页》.pdf》由会员分享，可在线阅读，更多相关《ITU-T V 58-1994 Management Information Model for V-Series DCE-S - Data Communication over the Telephone Network《V系列 DCE 的管理信息模式-电话网络上的数据交流 第14研究组 第65页》.pdf（65页珍藏版）》请在麦多课文档分享上搜索。

1、- STD-ITU-T RECMN V-58-ENGL 1794 H 4b2571 Ob20306 304 INTERNATIONAL TELECOMMUNICATION UNION ITU-T TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU V.58 (09/94) DATA COMMUNICATION OVER THE TELEPHONE NETWORK MANAGEMENT INFORMATION MODEL FOR V-SERIES DCES ITU-T Recommendation V.58 (Previously “CCIlT Rec

2、ommendation”) FOREWORD The -T (Telecommunication Standardization Sector) is a permanent organ of the International Telecommunication Union (m). The -T is responsible for studying technical, operating and tariff questions and issuing Recommen- dations on them with a view to standardizing telecommunic

3、ations on a worldwide basis. The World Telecommunication Standardization Conference (WTSC), which meets every four years, establishes the topics for study by the ITU-T Study Groups which, in their turn, produce Recommendations on these topics. The approval of Recommendations by the Members of the IT

4、-T is covered by the procedure laid down in WTSC Resolution No. 1 (Helsinki, March 1-12, 1993). -T Recommendation V.58 was prepared by IT-T Study Group 14 (1993-1996) and was approved under the WTSC Resolution No. 1 procedure on the 20th of September 1994. NOTE In this Recommendation, the expression

5、 “Administration” is used for conciseness to indicate both a telecommunication administration and a recognized operating agency. O 1994 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mic

6、rofilm, without permission in writing from the IT. . STD-ITU-T RECMN V-58-ENGL 1974 Li8b257L Ub20308 187 CONTENTS 1 Introduction . 1 .i Scope 1.2 Compliance Requirements 1.3 Structure of this Recommendation . 2 Information Model Overview . 3 Object Classes 3.1 3.2 3.3 3.4 3.5 V-Series Call Control M

7、anaged Object . 3.1.1 Managed Object Template . 3.1.2 Attributes . 3.1.3 Actions . 3.1.4 Notifications V-Series Data Compression Managed Object . 3.2.1 Managed Object Template . 3.2.2 Attributes 3.2.3 Actions 1 . 3.2.4 Notifications . V-Series DCE Managed Object 3.3.1 Managed Object Template . 3.3.2

8、 Attributes . 3.3.3 Actions . 3.3.4 Notifications . V-Series DTE Interface Managed Object . 3.4.1 Managed Object Template . 3.4.2 Attributes 3.4.3 Actions . 3.4.4 Notifications V-Series Error Control Managed Object . . 3.5.1 Managed Object Template . 3.5.2 Attributes . 3.5.3 Actions . 3.5.4 Notifica

9、tions Recommendation V.58 (09/94) Page 1 1 1 2 2 2 2 2 3 6 7 7 7 8 10 10 10 10 Il 13 15 15 15 16 24 24 24 24 25 29 29 1 3.6 3.7 3.8 3.9 V-Series Line Interface Managed Object . 3.6.1 Managed Object Template 3.6.2 Attributes . 3.6.3 Actions 3.6.4 Notifications V-Series Signal Convertor Managed Object

10、 3.7.1 Managed Object Template 3.7.2 Attributes . 3.7.3 Actions 3.7.4 Notifications V-Series Test Function Managed Object 3.8.1 Managed Object Template 3.8.2 Attributes . 3.8.3 Actions 3.8.4 Notifications Local defined types . 4 Relationships between managed object classes Appendix I - Some addition

11、al background information . Appendix II - List of Attributes, Actions and Notifications . Appendix III - References . Puge 30 30 30 34 34 35 35 36 44 45 46 46 46 48 50 50 51 53 54 60 II Recommendation V.58 (09/94) Recommendation V.58 MANAGEMENT INFORMATION MODEL FOR V-SERIES DCES (Geneva, 1994) The

12、ITU-T, considering (a) interfaces, basic and special functions and testing facilities; (b) enhanced management capabilities; (c) (4 (e) information; that V-Series Recommendations form a set of specifications for DCEs including the definition of external that it is expected that further Recommendatio

13、n will be published specifying newer DCEs, which offer that Recommendation M.3010 defines the principles for a Telecommunications Management Network (TMN); that Recommendation G.773 defines the protocol suites for Q-interfaces; that Recommendation M.3 100 defines a Generic Network Information Model

14、for the exchange of management recommends that the management of V-Series DCEs be carried out using the information model defined in accordance with the details contained in this Recommendation. 1 Introduction 1.1 Scope This Recommendation provides an information model for the V-Series DCEs. It iden

15、tifies the Telecommunications Management (TMN) object classes required for the management of Network Elements (NEs) defined by the Recommendations of the V-Series. These objects are relevant to information exchanged across standardized interfaces defined in Recommendation M.3010 TMN architecture. Th

16、e managed object classes in this Recommendation are specialized from the generic managed object classes defined in Recommendation M.3 1 O0 Generic Network Information model. This Recommendation does not define: - - the means by which management information may be exchanged among network elements; th

17、e network level management process. The information model defined in this Recommendation is concerned with the management of network elements, the equipment by which they are implemented and the functions contained within them. More precisely, it applies to the Equipment Domain visible at the Elemen

18、t Manager to Element interface, and is only concerned with the information available within that domain. Information proper to the domain of a Network Level Management Process is not included within this model. 1.2 Compliance Requirements The Recommendation does not require DCE behaviour that is inc

19、onsistent with other V-Series Recommendations, or with national regulatory requirements, and shall be interpreted accordingly. In order to be compliant with this Recommendation an implementation must: support at least the vSeriesDce Managed Object, if a Managed Object is supported, then at least the

20、 associated mandatory package shall be supported; if a package is supported, then all attributes, actions and notifications within the package shall be supported. If any of these relate to functions that are not implemented within the DCE, then any attempt to use the attribute or action will result

21、in nochange to the state of the DCE. - - - Recommendation V.58 (09/94) 1 1.3 Structure of this Recommendation Clause 2 provides an overview of the information model in this Recommendation. Clause 3 describes the information model using the notation mechanisms in Recommendation X.722 Guidelines for t

22、he Definition of Managed Objects. The relationships between managed object classes contained in this Recommendation are defined in clause 4. Appendix I contains some background information. 2 Information Model Overview The V-Series DCEs information model is based on the Generic Network Information m

23、odel of Recommen- dation M.3 100. The information exchanged at a management interface is modelled using design principles outlined in Recommendation X.720 Management Information Model. Resources are modelled as objects, and the management view of a resource is a managed object. Objects with similar

24、attributes may be grouped into Object classes. An object is characterized by its object class and object instance, and may posses multiple attribute types and associated values. The terms “managed object class” and “managed object instance” apply specifically to objects that are being managed. This

25、Recommendation specifies the properties of the resource visible for management. An object class may be a subclass of another Class. A subclass inherits attribute types, packages and behaviour of the super class, in addition to possessing its own specific attributes and properties. The object classes

26、 specific to the V-Series DCEs are all derived from super classes in the Generic Network Information Model Recommendation M.3 100. 3 Object Classes Object classes and attribute types are defined only for the purpose of communicating network management messages between systems, and need not be relate

27、d to the structure of data within those systems. NOTES 1 availability or enabled. 2 3 Where BIT STRING is used to identify options or selections a O indicates non-availability or disabled, a 1 indicates The request and confirm arguments of an Action are named actionNameReq and actionNameConf respect

28、ively. The CallProgress, DceBitrate, DceBitrateRange, DteBitrate, Eventpriority and PhoneNumber types are defined in 3.9. 3.1 V-Series Call Control Managed Object 3.1.1 Managed Object Template vSeriesCallContro1 MANAGED OBJECT CLASS - Source ITU-T SG14 Q4 - Status final drafi 6 June 1994 DERIVED FRO

29、M “Recommendation M.3100: 1992”:managedElement CHARACTERIZED BY callControlPkg PACKAGE ATTRIBUTES audioMonitor autoAnswerEnable autoCaUEnable au toCallModeSelect autoCallModesSupported autoRestoralEnable availableNumberCapaci ty blackListingActive callProgressState dceModeActive dceModeSelect dceMod

30、esSupported defaultCallA ttemptsTimer dialBackupEna ble GET-REPLACE, GET-REPLACE, GET-REPLACE, GET-REPLACE, GET, GET, GET, GET, GET, GET, GET-REPLACE, GET-REPLACE, GET-REPLACE, GET-REPLACE, 2 Recommendation V.58 (09194) STD-ITU-T RECMN V.58-ENGL 1994 48b257L Ob20312 bO8 directCallNumber GET-REPLACE,

31、 display CallProgressMessages GET-REPLACE, pauseDuringDialTime GET-REPLACE, ringsBefore Answer GET-REPLACE, telephoneNumbers GET-REPLACE, v25bisMode GET-REPLACE; ACTIONS dialconnect, dialDisconnect, NOTIFICATIONS callProgressEvents, revertedToLeasedLine, switchedToDialBackup; REGISTERED AS ccitt(O),

32、 recommendation(O), v(22), v58(58), vSeriesCallControl(0); 3.1.2 Attributes audioMonitor := SEQUENCE monitorEnable ENUMERATED Off (O), alwaysOn (U, monitorDia1 (21, monitorCallSetup (3) 1, low (01, normal (1) I monitorVolume ENUMERATED 1 This attribute controls the operation of the audio monitor (ty

33、pically a loudspeaker) which provides audible indication of modem dialling operations. Description: Operations: GET-REPLACE Behaviour: Specification not required Applications: Configuration Management Registered as: (vSeriesCallControl audioMonitor (O) autoAnswerEnable := BOOLEAN Description: Behavi

34、our: Specification not required Applications: Configuration Management Registered as: autoCallEnable := BOOLEAN Description: Behaviour: Specification not required Applications: Configuration Management Registered as: (vSeriesCallContro1 autoCallEnable (2) autoCallModeSelect : := ENUMERATED This attr

35、ibute is used to enable or disable auto answer or dial backup answer mode. Operations: GET-REPLACE (vSeriesCallControl autoAnswerEnable (1 ) This attribute is used to tnable or disable autocall or dial backup call mode. Operations: GET-REPLACE none (01, V-25 (11, v-25bis (21, v-at (3), cctl08-1 (4)

36、1 Description: Behaviour: Applications: Configuration Management Registered as: Indicates which automatic call mode is selected in the DCE. Must be one of autoCallModesSupported vSeriesCallContro1 autoCallModeSelect (3) ) Operations: GET-REPLACE Recommendation V.58 (09/94) 3 autoCailMoesSupported :=

37、 BIT STRING none (01, V-25 (11, -25bis (21, v-at (31, cctl08-1 (4) I Description: Operations: GET Behaviour: Specification not required Applications: Configuration Management Registered as: Indicates which automatic call modes are implemented in the DCE. vSeriesCallContro1 autoCallModesSupported (4)

38、 autoRestoralEnable := BOOLEAN Description: Behaviour: See dceModeActive Applications: Fault Management Registered as: This attribute is used to enable or disable automatic restoral to leased line. Ope rations: GET-REPLACE ( vSeriesCallControl autoRestoralEnable (5) availableNumberCapacity := INTEGE

39、R (0255) Description: Operations: GET Behaviour: Limits range of directCallNumber Applications: Configuration Management Registered as: Number of storage locations for maximum length telephone numbers remaining. ( vSeriesCallContro1 availableNumberCapacity (6) blackListingActive := BOOLEAN Descripti

40、on: Operations: GET Behaviour: Specification not required Applications: Fault Management Registered as: Indicates whether or not blacklisting is active in the DCE. vSeriesCallContro1 blacklistingActive (7) callProgressState : := CallProgress Description: Operations: GET Behaviour: Specification not

41、required Applications: Configuration Management Registered as: (vSeriesCallControl callProgressState (8) dceModeActive := ENUMERATED Indicates the state in the calling process the DCE is in. IeasedPointToPoint (O), IeasedMul tipointcontrol (11, IeasedMultipointTributar y (21, dialAutocal1 (31, dialA

42、utoanswer (41, dialBackupCal1 (51, dialBackupAnsw (61 I Description: If DCE is capable of operating in leased line or GSTN mode, this parameter indicates the current mode of operation. Operations: GET Behaviour: See dceModeSelect Applications: Configuration Management Registered as: vSeriesCallContr

43、o1 dceModeActive (9) 4 Recommendation V.58 (09/94) STD*ITU-T RECMN VDSB-ENGL 177i i8b259L Ub20314 Li80 9 dceModeSelect := BIT STRING IeasedPointToPoint (O), IeasedMultipointControl (11, IeasedMultipointTributary (2), dialAutocal1 (9, dialAutoanswer (41, dialBackupCail (51, dialBackupAnsw (6) 1 Descr

44、iption: If DCE is capable of operating in leased line or GSTN mode, this parameter specifies the selected mode(s) of operation. More than one mode can be selected, if dialBackupEnable or autoRestoralEnable is TRUE. Operations: GET-REPLACE Behaviour: Applications: Configuration Management Registered

45、as: (vSeriesCailContro1 dceModeSelect (io) dceModesSupported := BIT STRING IeasedPointToPoint (O), IeasedMultipointControl (11, IeasedMultipointTributary (2), dialAu tocall (31, dialAutoanswer (41, dialBackupCal1 (51, dialBackupAnsw (6) 1 Description: Operations: GET Behaviour: See dceModeSelect App

46、lications: Configuration Management Registered as: defaultCallAttemptsTimer := INTEGER (0255) Description: Behaviour: Specification not required Applications: Fault Management Registered as: dialBackupEnable := BOOLEAN Description: Behaviour: See dceModeSelect Applications: Fault Management Register

47、ed as: directCallNumber := SEQUENCE OF PhoneNumber Description: Indicates the modes the DCE can support. vSeriesCallContro1 dceModesSupported (1 1) This attribute defines the time in 10 second increments between call attempts. Operations: GET-REPL ACE vSeriesCallContro1 defaultCallAttemptsTimer ( 12

48、) ) Enables the DCE to dial backup. operations: GET-REPLACE vSeriesCailContro1 dialBackupEnable (i 3) In GSTN mode this determines the default call number. In Leased Line mode this determines the dial backup number. This is a list of stored telephone numbers. In GSTN mode these will be tried in orde

49、r. In Leased Line Mode when using double dial backup the numbers will be regarded as pairs, the first as the transmit direction, second as receive direction, etc. The maximum number of phone numbers remaining is given by availableNumberCapacity. Operations: GET-REPLACE Behaviour: Applications: Configuration Management Registered as: (vSeriesCallContro1 directCallNumber (14) display CallProgressMessages := BOOLEAN Description: Behaviour: Applications: Configuration Management Registered as: Determin