ITU-T S 34-1993 Intex Terminals - Requirements to Effect Interworking with the International Telex Service - Telegraphy Alphabetical Telegraph Terminal Equipment (Study Group IX) 5.pdf

《ITU-T S 34-1993 Intex Terminals - Requirements to Effect Interworking with the International Telex Service - Telegraphy Alphabetical Telegraph Terminal Equipment (Study Group IX) 5.pdf》由会员分享，可在线阅读，更多相关《ITU-T S 34-1993 Intex Terminals - Requirements to Effect Interworking with the International Telex Service - Telegraphy Alphabetical Telegraph Terminal Equipment (Study Group IX) 5.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、ITU-T RECMNxS-34 93 48b259L 058bYb3 T44 INTERNATIONAL TELECOMMUNICATION UNION ITU-T TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU TELEGRAPHY ALPHABETICAL TELEGRAPH TERMINAL EQUIPMENT s.34 (03/93) INTEX TERMINALS - REQUIREMENTS TO EFFECT INTERWORKING WITH THE INTERNATIONAL TELEX SERVICE ITU-T Recom

2、mendation S.34 (Previously ”CCITT Recommendation”) FOREWORD The ITU Telecommunication Standardization Sector (ITU-T) is a permanent organ of the International Telecom- munication Union. The ITU-T is responsible for studying technical, operating and tariff questions and issuing Recommendations on the

3、m with a view to standardizing telecommunications on a worldwide basis. The World Telecommunication Standardization Conference (WTSC), which meets every four years, established the topics for study by the ITU-T Study Groups which, in their turn, produce Recommendations on these topics. ITU-T Recomme

4、ndation S.34 was prepared by the ITU-T Study Group IX (1988-1993) and was approved by the WTSC (Helsinki, March 1-12. 1993). NOTES 1 As a consequence of a reform process within the International Telecommunication Union (ITU), the CCITT ceased to exist as of 28 February 1993. In its place, the ITU Te

5、lecommunication Standardization Sector (ITU-T) was created as of 1 March 1993. Similarly, in this reform process, the CCIR and the IFRB have been replaced by the Radiocommunication Sector. In order not to delay publication of this Recommendation, no change has been made in the text to references con

6、taining the acronyms “CCITT, CCIR or IFRB” or their associated entities such as Plenary Assembly, Secretariat, etc. Future editions of this Recommendation will contain the proper terminology related to the new ITU structure. 2 telecommunication administration and a recognized operating agency. In th

7、is Recommendation, the expression “Administration” is used for conciseness to indicate both a O ITU 1994 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in w

8、riting from the ITU. ITU-T RECMN*S=3q 93 W qBb259L 0586465 817 W Recommendation S.34 INTEX TERMINALS - REQUIREMENTS TO EFFECT INTERWORKING WITH THE INTERNATIONAL TELEX SERVICE (Helsinki, 1993) The CCIT, considering (a) that new networks are being introduced based upon stored program control techniqu

9、es; (b) that these networks as well as being able to carry the international telex service, can also carry the Intex service using alphabets other than International Telegraph Alphabet No. 2 and that interworking between these services is essential : (cl that the Intex service requires the establish

10、ment of new types of signalling, and that these signalling types shall permit interworking between Intex terminals, between telex terminals and Intex terminals, and between telex terminals and terminals capable of operating both telex and Intex dual service terminais; (d) (e) service and the Intex s

11、ervice; that Recommendation S.33 defines the alphabet and presentation characteristics for the Intex service; that Recommendation U.21 O defines the network interworking requirements between the intemational telex (9 that Recommendation S.35 defines the coding of answerbacks for the Intex service; (

12、i?) (h) Intex service and the international telex service; that Recommendation F. 150 defines the operational and service requirements of the Intex service; that Recommendation F.82 defines the operational and service requirements for interworking between the (i) provisions of this Recommendation sh

13、ould be applied to such services. that a prompt response to the WRUENQ request is required. NOTE - The development in the future of services similar to Intex may occur. It may be possible that some of the unanimously declares rhe view When interworking with the international telex service Intex term

14、inals must include the operating features contained in either Clause i or Clause 2 as applicable to the type of network to which the terminal is connected in order to ensure that there is no impact on the existing international telex service. Clause i details the requirements for interworking with t

15、he international telex service applicable to terminals connected to networks which are able to perform speed and code conversion (Type 1 networks as described in Recommen- dation U.2 10). Clause 2 details the requirements for interworking with the international telex service applicable to terminals

16、connected to networks which dynamically adjust the speed and code of circuits involved in a call (Type 2 networks as described in Recommendation U.210). The Intex terminal shall ensure that both parties to the call have identical records on calls to subscribers of the international telex services. F

17、or both Type 1 and Type 2 network operation, the operator shall be informed if a message for transfer to the destination telex terminal, either manually or automatically, contains non-ITA2 characters. The method of informing the operator is not a subject for international standardization. The Intex

18、operator has the opportunity to remove the non-ITA2 characters from the message for example by replacing characters with a meaningful equivalent to retain the sense of the message, e.g. IA5 character 2/6 (&) ampersand could be replaced with the word “and” and IA5 character 4/0 () “commercial at” cou

19、ld be replaced with the word “at”. Recommendation S.34 (0-3) 1 ITU-T RECMNxS.34 93 4862591 0586466 753 W In ?Telex Interworking Mode? an Intex terminal shall not allow printing enhancements such as bold printing or underlining in the local record and shall display alpha characters as either upper or

20、 lower case but not both. 1 Requirements for terminais connected to Type 1 networks 1.1 the call both terminals should receive a Speed Indicator sequence for the network (see Recommendation U.101). When a call is established between two customers with the Intex service then, as confirmation, at the

21、start of If no Speed Indicator sequence is received within 1.5 seconds from transmission or reception of the called terminal?s answerback then an Intex terminal shall determine that it is connected to a telex terminal and shall immediately print (or display) the ?telex service identifier-TLX?, defau

22、lt to ?Telex Interworking Mode? and then operate as detailed in the following subclauses. In general, it is required that the Intex terminal adjusts its character rate, line length and range of characters transmitted in order to ensure that the message presentation is identical at both ends of the c

23、all. 1.2 transmitted characters such that the time between the start of each character is not less than 150 milliseconds. When transmitting to a telex terminal, an Intex terminal shall extend the interval between successive 1.3 When transmitting to a telex terminal, an Intex terminal shall not trans

24、mit more than 69 printing or spacing characters between transmissions of new line sequences comprising C/R and UF. The local record for such transmissions shall also have a line length restricted to 69 characters to ensure that both parties to the call have identical records. 1.4 received. Transmiss

25、ion shall only recommence after reception of IA5 character 1/1 (DC1). On calls to and from telex terminals an Intex terminal shall halt transmission if an IA5 character 1/3 (DC3) is NOTE -This enables the network to effect flow control with the Intex terminal. Such control may be required from time

26、to time to allow the 50-baud character buffer in the network to catch up, for example, in the event of a large number of F/S andior US changes being required in the text. If the terminal does not start to transmit again after the network has sent a DC1 character, the network will continue to send su

27、ch characters at frequent intervals until a response is obtained. This will avoid a call being locked up in the event of a terminal missing the first DCl character due, for example, to corruption (see Recommendation U.210). 1.5 answerback to be generated in accordance with Recommendation S.35. The I

28、A5 character 015 (ENQ) shall be used to request the answerback or, if received, shall cause the 2 Requirements for terminals connected to Type 2 networks 2.1 a Telex Indicator sequence (see Recommendation U. 101). On calls to/from the international telex service an Intex terminal connected to a Type

29、 2 network should receive If a calling Intex terminal receives a Telex Indicator sequence before the called customers answerback it shall determine that the call has been terminated in the international telex network. Similarly, if a called Intex terminal receives a Telex Indicator sequence before a

30、 WRU signal at the start of a call it shall determine that the call originates in the international telex network. In either event the Intex terminal shall immediately print (or display) as the ?telex service identifier-?LX?, switch to ?Telex Interworking Mode? and then operate as detailed in the fo

31、llowing subclauses. If no Telex Indicator sequence is detected by a called or calling Intex terminal, the terminal shall determine that it is connected to another Intex terminal. In general, it is required that the Intex terminal adjusts its modulation rate, character structure, line length and rang

32、e of characters transmitted in order to ensure that the message presentation is identical at both ends of the call. 2 Recommendation S.34 (03/93) ITU-T RECMN*S*34 93 4862571 0586467 b9T 2.2 only be able to transmit, ITA2 characters at a nominal modulation rate of 50 bauds. Within 50 milliseconds of

33、receiving a Telex Indicator sequence the terminal shall be ready to receive, and shall 2.3 When transmitting to a telex terminal, an Intex terminal shall not transmit more than 69 printing or spacing characters between transmissions of new line sequences comprising C/R and L/F. The local record for such transmissions shall also have a line length restricted to 69 characters to ensure that both parties to the call have identical records. Recommendation S.34 (03/93) 3