ITU-R P 1622-2003 Prediction methods required for the design of Earth-space systems operating between 20 THz and 375 THz《运行于20 THz和375 THz之间的地球-空间系统设计所必须的预测方法》.pdf

《ITU-R P 1622-2003 Prediction methods required for the design of Earth-space systems operating between 20 THz and 375 THz《运行于20 THz和375 THz之间的地球-空间系统设计所必须的预测方法》.pdf》由会员分享，可在线阅读，更多相关《ITU-R P 1622-2003 Prediction methods required for the design of Earth-space systems operating between 20 THz and 375 THz《运行于20 THz和375 THz之间的地球-空间系统设计所必须的预测方法》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 Rec. ITU-R P.1622 1 RECOMMENDATION ITU-R P.1622 Prediction methods required for the design of Earth-space systems operating between 20 THz and 375 THz (Question ITU-R 228/3) (2003) The ITU Radiocommunication Assembly, considering a) that the spectrum between 20 THz and 375 THz is suitable for certa

2、in space-based communications in near-Earth and deep space environments; b) that for the proper planning of Earth-space systems operating between 20 THz and 375 THz, it is necessary to have appropriate propagation prediction techniques; c) that methods have been developed for the prediction of the m

3、ost significant propagation-related impacts to Earth-space systems operating between 20 THz and 375 THz; d) that as far as possible, these methods have been tested against available data and have been shown to yield an accuracy that is both compatible with the natural variability of propagation phen

4、omena and adequate for most present applications in planning of systems operating between 20 THz and 375 THz, recognizing a) that No. 78 of Article 12 of the ITU Constitution states that a function of the Radio-communication Sector includes, “ carrying out studies without limit of frequency range an

5、d adopting recommendations ”, recommends 1 that the methods for predicting propagation-related system impacts given in Annexes 1 and 2 be used for planning Earth-space systems in the respective ranges of validity indicated in Annexes 1 and 2. NOTE 1 Supplementary information related to fundamental p

6、ropagation data for frequencies between 20 THz and 375 THz may be found in Recommendation ITU-R P.1621. Annex 1 1 Introduction The Earths atmosphere is complex and dynamic and will impact the performance of a system operating in the frequency range 20 THz to 375 THz between the Earth and an orbiting

7、 spacecraft. These system impacts include: an overall loss in signal amplitude due to absorption by molecules of atmospheric gasses present along the propagation path; 2 Rec. ITU-R P.1622 an overall loss in signal amplitude and an increase in background noise due to scattering by particles ranging i

8、n size from fractions of a wavelength to many wavelengths present along the propagation path; fluctuations in the received amplitude and phase of the signal due to turbulence caused by thermal variations in the atmosphere. The representative techniques and equations required to carry out the necessa

9、ry prediction methods are presented in the following sections of this Annex. 2 Absorption losses Calculations of atmospheric absorption are possible using a line-by-line method similar to that which is provided in Recommendation ITU-R P.676. However, as thousands of individual lines are present acro

10、ss the spectral range from 10 THz to 1 000 THz (30 m to 0.3 m), such a method is computationally intensive and cumbersome. The windows of low atmospheric absorption are identified within the astronomical community with standardized filters as described in Table 1. The centre frequencies of these fil

11、ters provide an estimate of the regions of spectrum usable for communication along Earth-space paths in terms of the absorptive characteristics of the atmosphere only. As absorption is dependent, in part on local temperature, pressure, and atmospheric chemistry, the bandwidth of the filters does not

12、 necessarily correspond with the bandwidth of the regions of low atmospheric absorption. The four highest frequency bands represent a continuum of visible and ultraviolet spectrum with relatively low atmospheric absorption rather than distinct low absorption regions. Measurements of atmospheric abso

13、rption should be conducted whenever possible prior to the deployment of an earth station. TABLE 1 Standard astronomical filters for frequencies above 15 THz Filter Q N M L L K H Centre frequency (THz) 15 30 63 79 86 136 180 Wavelength (m) 20.25 10.1 4.80 3.80 3.50 2.20 1.65 Bandwidth (THz) (m) 15.2

14、6.50 18.2 5.70 15.9 1.20 14.7 0.70 17.3 0.70 30.1 0.48 33.3 0.30 Filter J IJISR V B U Centre frequency (THz) 240 330 370 430 560 700 830 Wavelength (m) 1.25 0.90 0.80 0.70 0.54 0.43 0.36 Bandwidth (THz) (m) 74.7 0.38 90.5 0.24 115.10.24 138.10.22 93.2 0.09 164.5 0.10 163.60.07 Rec. ITU-R P.1622 3 3

15、Scattering losses Scattering is generally defined as the redirection of energy by particles present along the propagation path. The primary effects to communication systems operating at frequencies between 20 THz and 375 THz in free space appear when: particles with a diameter approximately equal to

16、 the transmitted signal wavelength, present along the propagation path, redirect the transmitted signal away from its intended path; particles with a diameter much smaller than the transmitted signal wavelength, present in the propagating medium, redirect extraneous energy into the intended receiver

17、. 3.1 Attenuation of the transmitted signal due to Mie scattering Mie scattering is the predominant source of losses at frequencies below 375 THz, and is largely caused by microscopic particles of water. When local measurements characterizing the atmosphere are not available, the method described be

18、low can be used for calculating attenuation due to scattering along Earth-space paths. If measurements are available, a detailed calculation, provided in Annex 2, may be used. The following method is appropriate for earth stations located at altitudes between 0 and 5 km above sea level and between 1

19、50 THz and 375 THz, the frequencies most often associated with telecommunication through free space. The method is accurate to within approximately 0.1 dB assuming elevation angles above 45. However, local atmospheric conditions may lead to several dBs of variability. The following parameters are re

20、quired: : wavelength (m) hE: height of the earth station above mean sea level (km) : elevation angle. Step 1: Calculate the wavelength-dependent empirical coefficients: 0038.0002.0000545.02+=a (1a) 0439.00232.000628.02+=b (1b) 18.0101.0028.02+=c (1c) 719.026.1922.0228.023+=d (1d) Step 2: Calculate t

21、he extinction ratio, , from hEto : 123kmdhchbhaEEE+= (2) Step 3: Calculate atmospheric attenuation due to scattering, AS, along path: )sin(3429.4=SA dB (3) 4 Rec. ITU-R P.1622 3.2 Increases in background noise due to Rayleigh scattered solar energy Rayleigh scattering is negligible for systems opera

22、ting below 375 THz. The most significant result of Rayleigh scattering to systems operating above 375 THz is the introduction of background noise into receivers. Background noise appears in both the Earth-to-space and space-to-Earth directions. The primary noise source for earth stations operating w

23、ith spacecraft comes from Rayleigh scatter of sunlight during daytime operations. Spacecraft pointed at the Earth will also encounter noise from sunlight scattered from the Earths surface. 4 Effects of turbulence on systems operating between 20 THz and 375 THz As discussed in Recommendation ITU-R P.

24、1621, the magnitude of turbulence is measured in terms of a 2nC profile. The impacts of turbulence can be generally categorized as: amplitude scintillation caused by a redistribution of energy within the beam; apparent changes in the angle of arrival of the incoming signal; beam wander resulting in

25、deflection of the beam centroid away from the axis of propagation; beam spreading caused by unequal refraction across the wavefront resulting in decreased power in the plane of the receiving antennas aperture. 4.1 Amplitude scintillation Turbulence at frequencies between 150 THz and 375 THz causes G

26、aussian distributed fluctuations in the log-irradiance, N, of an incoming wave, called scintillation, by spatially redistributing its power across the surface of the wavefront randomly in time. The strength of scintillation is measured in terms of the variance of the beam amplitude. The following pa

27、rameters are required to calculate the strength of scintillation: h0: height of earth station above ground level (m) : wavelength : elevation angle Z : effective height of the turbulence (typically 20 000 m). Scintillation is traditionally given in terms of the variance, 2, of ln(N ) by: =ZhnNhhhCk0

28、26/526/116/72lnNpd)(sec253.2 (4a) where: k : wavenumber (= 2/) : wavelength (m) : zenith angle h : height above ground level (m). Rec. ITU-R P.1622 5 This is equivalent to: 26/116/76/50282lnNpsind)()(10924.10=ZhnNhhhhC(4b) where the wavelength, , is in m, and the other parameters are given as above.

29、 If desired, this is easily converted to dBN of fluctuation by multiplying the coefficient in the numerator by the change-of-base ratio and a factor of 10 resulting in: 26/116/76/50292ln22dBdBsind)()(10622.3)10ln(100=ZhnNNhhhhC(4c) If local measurements of 2nC are not available, the profile of )(2hC

30、nin 5.1.1 of Recommen-dation ITU-R P.1621 may be used. Table 2 provides examples for selected frequencies in the 10 THz to 1 000 THz (30 m to 0.3 m) spectral region. Values of 2lnN and 2dBN for each of the frequencies are calculated assuming the turbulence structure profile provided in 5.1.1 of Reco

31、mmendation ITU-R P.1621, the aperture size is less than the atmospheric coherence length, r0, an elevation angle of 75, earth station antenna is 5.5 m above the ground, and for r.m.s. wind speed along the vertical path, vrms, of 21 m/s and 30 m/s. TABLE 2 Example scintillation statistics 4.1.1 Ampli

32、tude scintillation on paths in the Earth-to-space direction The variance of log-irradiance, on paths in the Earth-to-space direction, 2sE will remain small (4). Experiments have verified that there is a low probability of exceeding this limit. Typically, 2lnN drops about two orders of magnitude as f

33、requency increases from 24 THz to 750 THz (12.5 m to 0.4 m). Aperture averaging is generally not considered on paths in the Earth-to-space direction. A wavefront exiting the atmosphere experiences the same spatial redistribution of energy across its surface as occurs in the space-to-Earth direction.

34、 However, diffraction of the wavefront, as it propagates through space, spreads individual amplitude and phase perturbations across large areas. 2lnN2dBN2lnN2dBNFrequency (THz) Wavelength (m) (vrms= 21 m/s) (vrms= 30 m/s) 563.9 0.532 0.23 4.41 0.36 6.88 352.9 0.850 0.14 2.58 0.21 3.98 282.0 1.064 0.

35、10 1.93 0.16 3.12 193.5 1.55 0.07 1.29 0.10 1.93 6 Rec. ITU-R P.1622 Thus the phase coherence radius at the receiving aperture on a spacecraft is much larger than the probable size of the spacecraft receiver aperture ( 1 m). Therefore no aperture averaging occurs and scintillation appearing at the r

36、eceiver is given by: 22ln2NpNsE=(5) For operation at 150 THz (2.0 m), when 2lnN is about 0.15, 4 dB fades occur about 1% of the time with a frequency and duration of about 150 Hz and 105s. 4.1.2 Amplitude scintillation on paths in the space-to-Earth direction The impact of scintillation on paths in

37、the space-to-Earth direction can be large enough to severely limit performance of receivers. If the receiver has a finite aperture larger than the atmospheric coherence length, r0, the effect of scintillation is spatially averaged over the aperture resulting in a reduction of 2lnN . While aperture a

38、veraging can mitigate amplitude scintillation effects, the corrupted phase can significantly degrade the performance of single spatial-mode optical receiver systems such as coherent detection or preamplified direct detection. The value of 2lnN on paths in the space-to-Earth direction, 2Es, is modifi

39、ed by an aperture averaging factor, A. The aperture averaging factor is defined as the ratio of the variance of log-irradiance obtained from a finite size collecting aperture to the corresponding quantity obtained from a point aperture and is calculated by: Step 1: Calculate the turbulence scale hei

40、ght, z0, by: md)(d)(7/66/5222000=ZhnZhnhhhChhhCz (6) where: h0: height of earth station above ground level (m) h : height above ground level (m) Z : effective height of turbulence above ground level (typically 20 000 m). Step 2: Calculate the aperture averaging factor, A, by: 6/7027sin101.111+=zDA (

41、7) where: D : diameter of the earth station aperture (m) : elevation angle : wavelength (m). Rec. ITU-R P.1622 7 Step 3: Calculate the variance of log-irradiance on a path in the space-to-Earth direction, ,2Esby: 22ln2NpNEsA=(8) 4.2 Angle of arrival Turbulence-induced fluctuations in the apparent an

42、gle of arrival of the received beam are due to variations in the refractive indices of the parcels of air along the propagation path. The effects of these fluctuations in the Earth-to-space direction are negligible. Typical r.m.s. angle of arrival variations are on the order of 1 rad and, thus, have

43、 little effect. However, in the space-to-Earth direction the r.m.s. fluctuations are more on the order of several rad and must be considered. The method described below can be used to calculate the variance of the angle of arrival, 2 , on paths in the space-to-Earth direction through a given turbule

44、nce profile, ,2nC for elevation angles greater than 45. The following parameters are required: h0: height of the earth station above ground level (m) : elevation angle DR: diameter of the receiver aperture (m) Z : the effective height of turbulence (typically 20 000 m). Step 1: Obtain the vertical t

45、urbulence profile of the atmosphere. If this long-term statistic cannot be obtained from local data sources, an estimate can be obtained from 5.1.1 of Recommen-dation ITU-R P.1621. Step 2: Calculate the integrated turbulence profile, , from: 3/12md)(0=ZhnhhC (9) where h is the height above ground le

46、vel (m). If local measurements of the integrated 2nC profile are not available, the empirical approximation given in equations (9) to (12) of Recommendation ITU-R P.1621 provides satisfactory results for most applications. Step 3: Calculate the variance of the angle of arrival, 2 , from: 2radsin914.

47、23/12=RD(10) Along paths in the space-to-Earth direction, the divergence of a beam and the long propagation distance through free space will make the wavefront much larger than r0by the time it reaches the 8 Rec. ITU-R P.1622 turbulence. Therefore, the effects of the atmosphere are averaged across t

48、he width of the beam. The term for antenna size in (11) accounts for the fraction of the beam seen by the earth station. 4.3 Beam wander Beam wander is the displacement of the beam from the intended propagation direction. Beam wander is significant in the Earth-to-space direction and can be on the o

49、rder of a beamwidth. At a distance L, the r.m.s. displacement of the wandering beam, rc, is given by: )(sind)(08023/120=TZhnrcDhhCL m (11a) where: L : propagation distance from the earth station to the satellite (km) DT: diameter of the transmitting aperture (m) h0: height of the earth station above ground level (m) h : height above ground level (m) Z : effective height of the turb