ISA 75 08 02-2003 Face-to-Face Dimensions for Flanged and Flangeless Rotary Control Valves (Classes 150 300 and 600 and PN 10 PN 16 PN 25 PN 40 PN 63 and PN 100)《无凸缘控制阀的面到面尺寸(等级150.pdf

《ISA 75 08 02-2003 Face-to-Face Dimensions for Flanged and Flangeless Rotary Control Valves (Classes 150 300 and 600 and PN 10 PN 16 PN 25 PN 40 PN 63 and PN 100)《无凸缘控制阀的面到面尺寸(等级150.pdf》由会员分享，可在线阅读，更多相关《ISA 75 08 02-2003 Face-to-Face Dimensions for Flanged and Flangeless Rotary Control Valves (Classes 150 300 and 600 and PN 10 PN 16 PN 25 PN 40 PN 63 and PN 100)《无凸缘控制阀的面到面尺寸(等级150.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 AMERICAN NATIONAL STANDARD ANSI/ISA-75.08.02-2003 (R2009) Face-to-Face Dimensions for Flanged and Flangeless Rotary Control Valves (Classes 150, 300, and 600) Approved 19 August 2009 ANSI/ISA-75.08.02-2003 (R2009) Face-to-Face Dimensions for Flanged and Flangeless Rotary Control Valves (Classes 150

2、, 300, and 600) ISBN: 978-1-936007-24-0 Copyright 2009 by the International Society of Automation. All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (el

3、ectronic mechanical, photocopying, recording, or otherwise), without the prior written permission of the Publisher. ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709 - 3 - ANSI/ISA-75.08.02-2003 (R2009) Copyright 2009 ISA All rights reserved. Preface This preface, as

4、 well as all footnotes and annexes, is included for information purposes and is not part of ANSI/ISA-75.08.02-2003 (R2009). The standards referenced within this document may contain provisions which, through reference in this text, constitute requirements of this document. At the time of publication

5、, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers o

6、f currently valid International Standards. ANSI maintain registers of currently valid U.S. National Standards. This document has been prepared as part of the service of the International Society of Automation (ISA), toward a goal of uniformity in the field of instrumentation. To be of real value, th

7、is document should not be static but should be subject to periodic review. Toward this end, the Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Te

8、lephone (919) 549-8411; Fax (919) 549-8288; E-mail: standardsisa.org. The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standa

9、rds. The Department is further aware of the benefits to USA users of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric

10、 units in all new and revised standards, recommended practices, and technical reports to the greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric System, published by the American Society for Testing it is a dimension for only the valve itself. ANSI

11、/ISA-75.08.02-2003 (R2009) - 14 - Copyright 2009 ISA All rights reserved. 5 References INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) Publication 60534-3-2 (2001) Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves Ava

12、ilable from: IEC 3, rue de Varemb P.O. Box 131 CH - 1211 Geneva 20 Switzerland http:/www.iec.ch 15 ANSI/ISA-75.08.02-2003 (R2009) Copyright 2009 ISA All rights reserved. Annex A Dimensions for metrically sized valves This annex is not part of ANSI/ISA-75.08.02-2003 (R2009), but it is included to fac

13、ilitate its use. Face-to-face dimensions to start this standard were obtained from Scientific Apparatus Makers Association (SAMA), Proposed Standard PMC 23.3e-1975, “Face-to-Face Dimensions of Flangeless Control Valves.” Dimensions for metrically sized valves are nominal conversions that are convent

14、ionally used in the Manufacturers Standardization Society (MSS) of the Valve and Fitting Industry (MSS-SP86-1997), International Standards Organization (ISO), and International Electrotechnical Commission (IEC). This page intentionally left blank. Developing and promulgating sound consensus standard

15、s, recommended practices, and technical reports is one of ISAs primary goals. To achieve this goal the Standards and Practices Department relies on the technical expertise and efforts of volunteer committee members, chairmen and reviewers. ISA is an American National Standards Institute (ANSI) accre

16、dited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Societys standards program, please write: ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709 ISBN: 978-1-936007-24-0