INTERN TMS 9008-2008 Painting Plastic - Interior And Exterior《塑胶喷漆 内部和外部》.pdf

《INTERN TMS 9008-2008 Painting Plastic - Interior And Exterior《塑胶喷漆 内部和外部》.pdf》由会员分享，可在线阅读，更多相关《INTERN TMS 9008-2008 Painting Plastic - Interior And Exterior《塑胶喷漆 内部和外部》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS-9008 TITLE: Painting Plastic - Interior And Exterior CURRENT REV. No. : 0806 DATE: June 2008WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. N - December 2005 PRINTED COPIES OF THIS DOCUMENT MUS

2、T BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determi

3、ne the applicability of regulatory limits prior to use. Change Notice: Replaced “InternationalTruck and Engine Corporation” with “Navistar, Inc.” per corporate directive; revised requirements in Section 4.2.2.3; added CEMS B-50 requirement; added method of designation on drawings in Section 8.0; edi

4、torial changes. Reference: File 30-13A Keywords: Painting, painting plastic, painted trim. 1.0 APPLICATION This specification applies to plastic materials used in NAVISTAR trucks with painted surfaces. The specification covers painted (topcoated) parts both primed and unprimed. All topcoated parts s

5、hall meet the CEMS G-5 requirements as appropriate for the specified paint grade. Typical parts are pillar covers, trim panels, instrument cover pads, instrument panels, fenders, roofs, hoods and grilles. The specification also covers the second surface painting used on decorative parts (TMS-7085).

6、2.0 SCOPE This specification covers the qualification and processing, quality, quality control and source approval, and packaging requirements of painted plastic parts. 2.1 Restricted Chemical SubstancesEffective January 1, 2007, all product supplied to the requirements of this specification must co

7、mply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following specifications, standards, and regulations are referenced herein. Quality System Standard ISO 9001 or TS-16949 CEMS G

8、T-5A CEMS GT-4D CFR Title 29, Part 1910 CEMS GT- 5B ASTM D 79 NAVISTAR Manufacturing Std. MS-D-13 CEMS GT-6B ASTM D 638 NAVISTAR Eng. Design Std A-16 CEMS GT-7E ASTM G 154 CEMS G-5, Part V CEMS GT-12 SAE J400 CEMS DT-4 CEMS GT-28 CEMS GT-31 TMS-7085 CEMS B-504.0 REQUIREMENTS This specification is no

9、t intended to limit or to specify the exact processes and/or materials to be used in providing plastic parts that are topcoated or primed, ready for topcoating. The control of the primer quality and its application are the responsibility of the plastic supplier. All topcoated plastic parts shall be

10、compatible with all subsequent NAVISTAR paint finishing operations. This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page

11、 1 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: REVISION: TMS-9008 Painting Plastic Interior And Exterior 0806 This document is restricted and may not be se

12、nt outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. 4.1 Qualification Of Paint/Primers 4.1.1 Material/Process Approvals The primers used by the supplier must be approved by Materials Engineering at TDTC to meet the dry film requirements of Grade-52 and/or G

13、rade 52HS as per CEMS G-5, Part V, prior to their first use in production. In addition, parts primed with the materials and applications processes/methods to be used by the supplier shall be approved by Materials Engineering and, after approval, no deviation in materials and/or manufacturing process

14、es are permitted without approval by Materials Engineering. 4.2 Qualification Of Paint 4.2.1 Material The initial qualification tests of paint shall be performed on parts molded from the same material and by the same molding process in which the finished parts are specified. These panels shall be co

15、ated with the paint to be tested using the procedure listed below. In cases where a primer is specified in addition to the topcoat, the panels shall contain both coatings applied by the intended production process. These panels shall be submitted to Materials Engineering at TDTC for approval with th

16、e vendors test results. Final qualification shall be performed on the finished part prior to production release. 4.2.2 Sample Preparation 4.2.2.1 A minimum two (2) parts shall be submitted for qualification for each test. 4.2.2.2 Prior to painting, the samples shall be cleaned with solvents or clean

17、ers as necessary. This operation shall simulate production procedure. 4.2.2.3 The paint/primer shall be applied to a minimum dry film thickness to provide black/grey hiding (Morass chart) per the manufacturers recommended process. 4.2.2.4 The painted samples shall be cured by means which simulate pr

18、oduction procedures. Baking cycles shall not be detrimental to the base plastic. 4.3 Testing Finish painted parts, primed or unprimed, when topcoated with approved materials will meet the applicable requirements listed in the Table below. Test Test Method Requirements Adhesion GT-5A Steps 2,3,4 & 5

19、Under Procedure 95% Min. Accelerated Adhesion* GT-5C Steps 2,3,4,5,6 & 7 Under Procedure 95% Min. Initial Gloss GT-6B Step 3 Under Procedure Topcoat* see Section 4.6 Intercoat Adhesion GT-5B 95% Min. Color Topcoat Visual comparison Shall Match Color Standard in the TDTC Styling Department Mar Resist

20、ance GT-12 Steps 4.1 to 4.4 Under Procedure No Nail Marks Visible To The Unaided Eye Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 2 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction

21、 or networking permitted without license from IHS-,-,-NUMBER: TITLE: REVISION: TMS-9008 Painting Plastic Interior And Exterior 0806 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Gravelometer * SAE J400 2A a

22、s per GT-28 Humidity GT-7E Steps 4.2 to 4.5 (Under Procedure) Interior 100 Hours Exterior 500 Hours No Blistering At Conclusion Of Specified Time Accelerated Weathering (Applies to Topcoated Parts Only) GT-31 QUV Cyclic Ultraviolet Weathering Tester Exterior exposure: Xenon Arc per Method B Method C

23、 or D or Interior exposure: Xenon Arc per Method A Method E or F No Deterioration Or Color Change greater than a E of 3. Conductivity (Applies to primed parts only.) GT-18 110 * Exterior Parts Only Unless Otherwise Specified 4.4 Mechanical Properties - Painted Plastic Material In addition to the tes

24、t samples submitted above, the vendor shall supply an additional eight (8) parts - four painted and four unpainted. When these are tested for tensile strength (ASTM D 638), Gardner Impact (CEMS DT-4), and flexural modulus (ASTM D 79), the painted panel shall have properties that are a minimum of 70

25、percent of the value of the unpainted material properties. 4.5 Processing Finished painted production parts shall be produced by the same methods used on the qualification samples. Changes in processing must be approved by Materials Engineering at TDTC. 4.6 Gloss Requirement Minimum gloss requiremen

26、ts are indicated by suffix letters to the color number in the appearance designation. No suffix will be used when full gloss is required (83 minimum) or when specifying primers and casting sealers. Suffix letters and their respective gloss levels are as follows: Suffix 60 Gloss Suffix 60 Gloss Suffi

27、x 60 Gloss Suffix 60 Gloss Suffix 60 Gloss A 85 5 D 55 5 G 25 5 K 15 - 20 N 2 - 5 B 75 5 E 45 5 H 15 5 L 10 - 15 C 65 5 F 35 5 J 10 5 M 5 - 10 5.0 QUALITY Painted parts shall be adherent and uniform in color and texture, with no thin spots, runs, wrinkles, porosity, pits, blisters or nodules. Suppli

28、ers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 3 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: REVISION: TMS-9008 Pai

29、nting Plastic Interior And Exterior 0806 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. 5.1 Porosity In instances where porosity is not detectable until after the primed substrate has been painted, isolated

30、cases of porosity as defined in Table 1 shall not be cause for rejection. Porosity that is chronic and requires significant amounts of rework shall be cause for rejection and it is the responsibility of the supplier to correct this condition. The supplier has the responsibility to provide quality pr

31、imed parts which will not cause delayed defects after finishing in the using plant. This condition will require close cooperation with the paint facility and with Materials Engineering at TDTC. 5.2 Appearance RequirementsSpecific appearance requirements are given in Table 1. Appearance requirements

32、are specified for the following zones or locations on the vehicle: 5.2.1 Zone I Primary: exterior, glamour surfaces such as hoods and fender exteriors, including visible edges, grilles, cab fronts, sides, doors, corners, and lower aerodynamic fairings. 5.2.2 Zone II Secondary: exterior, glamour surf

33、aces such as cab tops, cab backs (between corner radii), and upper aerodynamic fairings. Also, primary interior, low gloss painted surfaces, such as engine covers and instrument panels. 5.2.3 Zone III Recessed exterior or interior surfaces, such as door openings, door ends, and painted grab handles.

34、 5.2.4 Zone IV Hidden areas, such as those covered in assembly and backsides, if primed. 5.2.5 Inspection Conditions Parts shall be inspected for appearance requirements at a distance of two feet under a light intensity of 100 foot-candles minimum at the part surface. 6.0 SOURCE APPROVAL AND QUALITY

35、 CONTROL6.1 Supplier RequirementsAll suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requi

36、rements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to the NAVISTAR Corporate Buyer upon request. 6.2 ApprovalParts supplied against contracts or purchase orders citing this specification shall be equivalent in all re

37、spects to those samples that were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall not

38、ify Materials Engineering at TDTC and Purchasing & Logistics of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be su

39、bmitted with the request for change. 6.3 Process ControlThe supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a

40、 process capable of providing all required properties. The part Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 4 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permit

41、ted without license from IHS-,-,-NUMBER: TITLE: REVISION: TMS-9008 Painting Plastic Interior And Exterior 0806 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. supplier and the plant metallurgist and/or the qu

42、ality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATIONShipping, packing and identification shall be in accordance with Manufacturing Standard MS-D-13. Parts shall be packed so as to protect the

43、 surface finish in transit. 8.0 DESIGNATION ON DRAWINGS Example: Topcoat per TMS-9008 9.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering

44、 and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN Information Handling Service (IHS) 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Suppliers are required to

45、assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 5 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TITLE: REVISION: TMS-9008 Painting Plastic Interi

46、or And Exterior 0806 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. TABLE 1 - APPEARANCE REQUIREMENTS ZONE REQUIREMENT I II III IV Gloss 60 90 min as specified 40-80 30-80 Orange Peel , min Wavescan: Test pe

47、r GT-29* or, ACT Comparison Test * 4.5 7 4.5 7 3.5 6 - 1 2 2 Craters greater than 1mm dia. Max. no. per sq. foot 2 max. per Unit 3 3 1.5mm max. 4 1.5 mm max. 6 1.5 mm max. Dirt particles*, max. no. per square foot 10 max. per Unit unlimited 3 3 3 Fine craters less than 1 mm dia., max. no. per sq. foot 2 max per Unit unlimited Solvent Pop None None None Acceptable Oversp