INTERN TMS 6818-2009 Refrigeration Lubricants《冷冻机油》.pdf

《INTERN TMS 6818-2009 Refrigeration Lubricants《冷冻机油》.pdf》由会员分享，可在线阅读，更多相关《INTERN TMS 6818-2009 Refrigeration Lubricants《冷冻机油》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 4 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER:

2、 TMS-6818 TITLE: Refrigeration Lubricants CURRENT REV No: 0908 DATE: August 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev C - June 2002 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous ma

3、terials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Replace

4、d “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added section 2.1 “Restricted Chemical Substances;” added section 10 “Technical Information;” editorial changes. Reference: File 30-8 Key words: A/C; Lubricant 1.0 APPLICATION This specification covers thre

5、e types of lubricants suitable for use in mobile air conditioning systems. Two of these are compatible with the HFC-134a refrigerant and the third is compatible with the discontinued R-12 refrigerant. These lubricants are used for factory fill, assembly applications, and in service applications. 1.1

6、 Type I: A mineral oil based lubricant compatible with R-12 refrigerant and commonly used as the compressor service oil in A/C systems using R-12 refrigerant. It is also commonly used as a lubricant for O-rings in the A/C fitting assemblies for both R-12 and HFC-134a refrigerant systems. 1.2 Type II

7、: A Polyal ester based synthetic lubricant that is compatible with HFC-134a refrigerant and is used only as a compressor oil in factory fill and service applications. 1.3 Type III: A Polyalkylene Glycol (PAG) based synthetic lubricant that is compatible with HFC-134a refrigerant and is used only as

8、a compressor oil in factory fill and service applications. 2.0 SCOPE This specification covers requirements for physical properties, source approval procedure, quality control, packaging and identification and approved sources of supply. 2.1 Restricted Chemical Substances Effective January 1, 2007,

9、all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are r

10、eferenced in this specification. Quality System Standard ISO 9001 or TS-16949 ASTM D 97 ASTM D 1298 NAVISTAR Mfg. Standard MS-D-13 ASTM D 445 ASTM E 326 CFR Title 29, Part 1910 ASTM D 2270 ASTM D 3945 NAVISTAR CEMS B-50 ASTM D 974 ASTM E 1064 ASTM D 93 ASTM D 1209 ISO 3448 Copyright Navistar Interna

11、tional Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6818 TITLE: Refrigeration Lubricants REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without

12、permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 2 of 4 4.0 PROPERTY REQUIREMENTS 4.1 General Lubricants purchased to this specification shall consist of suitably refined base stocks fortified with additiona

13、l functional additives as may be necessary to meet the requirements of this specification. 4.2 Material supplied shall meet all requirements of this specification. A written report certifying conformance to all requirements shall be provided before submitting samples for evaluation. The vendor shall

14、 demonstrate compatibility of his lubricant with all applicable system materials, including but not limited to, elastomers*, desiccants*, plastics and coatings. * Elastomeric materials shall be obtained from the appropriate manufacturers. The materials shall include: TMS-6021, Type V tube material,

15、o-rings, and seal materials. Please contact Materials Engineering at Truck Development and Technology Center for more information. * Desiccant materials shall be obtained from UOP, Molecular Sieves, 25 E. Algonquin Road, Des Plaines, IL 60017-5017. 4.3 Material supplied shall be suitable for the use

16、 intended, be manufactured with good commercial practice, and shall exhibit no objectionable odor. No re-refined base stocks shall be used. TABLE 1 PROPERTY AND PERFORMANCE REQUIREMENTS PROPERTY Type I Type II Type III TEST DESIGNATION Approximate ISO Viscosity Number 68 68 68 ISO 3448 Viscosity at

17、40 C Kinematic, mm2/s (cSt) 63-67 63-67 70-90 ASTM D 445 Viscosity at 100 C Kinematic, mm2/s (cSt) 6.5-7.5 12.5-15.5 14-19 ASTM D 445 Viscosity Index, min 46 205 200 ASTM D 2270 Pour Point, C, max -30 -30 -35 ASTM D 97 COC Flash Point, C, min 195 200 200 ASTM D 93 Total Acid Number, mg KOH/g, max 0.

18、25 0.25 1.10 ASTM D 974 Specific Gravity 15 C .894-.896 .996-.998 1.00-1.05 ASTM D 1298 Methylation, % min Report* 95 Report* ASTM E 326 Moisture, PPM, max Report* 500 1000 ASTM E 1064 Appearance Clear Clear Clear Color, Platinum-Cobalt Report* 400 Report* ASTM D 1209 Upper Miscibility: 5% in HFC-13

19、4a, C 10% in HFC-134a, C Report* Report* 54 51 Report* Report* TBD (May be extrapolated from solubility curve until a method is developed) Shear Stability, Viscosity Change, 40 C, % max Report* 1.0 Report* ASTM D 3945 Proc. B * Specification limits for these properties have not been determined as ye

20、t. Test values shall be reported. 5.0 QUALIFICATION The following shall be furnished to the Truck Development and Technology Center: 5.1 3.8 liters of each lubricant submitted for qualification. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo re

21、production or networking permitted without license from IHS-,-,-NUMBER: TMS-6818 TITLE: Refrigeration Lubricants REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume

22、 all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 3 of 4 5.2 Identification of the candidate lubricant by a distinctive formulation number, in addition to a brand name and/or product code number. 5.3 A summary of qualification test results and certification of approval by compressor man

23、ufacturers. 5.4 A summary of field test data. 5.5 Material Safety Data Sheet and complete physical and chemical properties. 5.6 Suppliers certification that the candidate lubricant meets all requirements of this specification. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements All sup

24、pliers to Navistar are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their c

25、ertification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples, which were ap

26、proved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes occur in material properties, processing practices, or labeling, the supplier shall notify Materials Engineering at TDTC and Navistar Purchasing and Supplier Developme

27、nt of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new/amended/updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Section 1910, shall be submitted with the request for change. 6.3 Process Control The

28、 supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The

29、part supplier and the plant metallurgist and/or the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Packaging and identification shall be in accordance with Manufacturing Standard MS-D

30、-13. When delivered in tank car or tank truck quantities, the material shall be accompanied by documents clearly indicating the Navistar designation, name of supplier, formula or code number, batch number, and date of manufacture. 7.1 When delivered in smaller bulk quantities, such as 208 liter (55

31、gallon) drums, the material shall be shipped in containers clearly marked with the International designation, name of supplier, formula or code number, batch number, and date of manufacture. Markings shall be at least 25 mm (1 in) high. 7.2 When packaged for retail sale, the material shall be suppli

32、ed in containers that have been approved by the Parts Marketing Division of the Parts Operation at Cantera, in Warrenville, Illinois. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,

33、-,-NUMBER: TMS-6818 TITLE: Refrigeration Lubricants REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Pag

34、e 4 of 4 Identification information and markings shall also be in accordance with requirements set forth by the Parts Marketing Division. 8.0 DESIGNATION ON DRAWINGS Example: Refrigerant Lubricant per TMS-6818, Type I In the case of lubricant ordered to the requirements of TMS-6818 without designati

35、on of the Type, Type II lubricant will be supplied. 9.0 APPROVED SOURCES Type I Part Number 2643016R1 Texaco Code 1562 Capella WF 68 Type II Part Number 2644109R1 Lubrizol LZ-2916 or ICI Americas, Inc. Emkarox RL 118D Type III Part Number 2644034R1 Union Carbide UCON Refrigeration Lubricant 993 10.0

36、 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne,

37、 IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-