INTERN TMS 6803-2009 Transmission Gear Lubricant《变速齿轮润滑剂》.pdf

《INTERN TMS 6803-2009 Transmission Gear Lubricant《变速齿轮润滑剂》.pdf》由会员分享，可在线阅读，更多相关《INTERN TMS 6803-2009 Transmission Gear Lubricant《变速齿轮润滑剂》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 1 of 4 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: T

2、MS-6803 TITLE: Transmission Gear Lubricant CURRENT REV. No: 0904 DATE: APRIL 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. G-1 August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardou

3、s materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Rep

4、laced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; updated Table 1; revised Approved Sources; editorial changes. Reference: File 30-8D Keywords: Gear Lubricant 1.0 APPLICATION This specification covers a gear lubricant suita

5、ble for use as a factory fill and service fill for heavy duty manual transmissions and transfer cases. (NAVISTAR Bulk P/N 2643022 R1 or Fleetrite P/N 991061 CX, where X is a number suffix identifying the current supplier). 2.0 SCOPE This specification covers requirements for properties, source appro

6、val procedure, quality control, packaging and identification, and approved sources of supply. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE D

7、OCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 API 1509 ASTM D892 NAVISTAR Mfg Standard MS-D-13 SAE J306 ASTM D22

8、73 NAVISTAR CEMS BT-9 ASTM D445 ASTM D130 NAVISTAR CEMS BT-10 ASTM D2270 ASTM D1550 NAVISTAR CEMS BT-43 ASTM D92 ASTM D1298 NAVISTAR CEMS BT-44 ASTM D97 ASTM D1500 CFR Title 29, Part 1910 ASTM D95 FSTM 791-3456.1 NAVISTAR CEMS B-50 4.0 PROPERTY REQUIREMENTS 4.1 General Lubricant purchased to this sp

9、ecification shall consist of suitably refined petroleum base stocks, fortified with rust and oxidation inhibitors, defoamers, and pour point depressants to meet API Service Designation GL-1 (American Petroleum Institute Specification, API 1509), SAE Viscosity Copyright Navistar International Corpora

10、tion Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6803 TITLE: Transmission Gear Lubricant REVISION: 0904 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission

11、from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 2 of 4 Grade 80W-90 (SAE J300 and SAE J306). The material and workmanship shall be in accordance with good commercial practice. The material shall be suitable for the use

12、 intended. 4.2 Physical and Chemical Product supplied will meet requirements indicated in Table 1. Table 1 Physical and Chemical Properties Property Requirement Test Designation (ASTM Unless Otherwise Specified) Kinematic Viscosity, mm/s At 100C At 40C 13.5 - 24.0 Report Value D445 Viscosity Index,

13、minimum 90 D2270 Temperature For Apparent Viscosity Of 150,000 cP, C, maximum -26 Channel Point, C, maximum -35 FTMS 791-3456.1 Pour Point, C, maximum -23 D97 Flash Point, C, minimum 165 D92 Foaming Tendency/Stability, ml, maximum Sequence I Sequence II Sequence III 20/0 50/0 20/0 D892 Trace Sedimen

14、t, Vol %, maximum 0.01 D2273 Water, Vol %, maximum 0.1 D95 Copper Strip Corrosion Rating, maximum (3 Hours At 121C) No. 1b D130 Humidity Corrosion Test (100 Hours) Pass CEMS BT-9 Calcium Report CEMS BT-43 Zinc Report CEMS BT-43 Phosphorus Report CEMS BT-44 Sulfur Report D1552 Appearance Clear Ph: 1-

15、800-854-7179. FTMS 791, General Services Administration, Washington, D.C. 20407 5.0 QUALITY All product supplied shall be clean and free from dirt, or harmful to product performance and have no objectionable odor. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements All suppliers to NAV

16、ISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification

17、with an accredited registrar and must furnish copies of registration certificates to their Corporate Buyer upon request. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchase

18、r. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, TDTC and Purchasing and Supplie

19、r Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Proces

20、s Control The supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required pro

21、perties. The part supplier and the plant metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Packaging and identification shall be in accordance with Manufacturing

22、Std. MS-D-13. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6803 TITLE: Transmission Gear Lubricant REVISION: 0904 This document is restricted and may not be sent ou

23、tside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 4 of 4 7.1 When delivered in tank car or tank truck quantities, the material shall be accompanied by documents clear

24、ly indicating the NAVISTAR designation, name of supplier, formula or code number, batch number, and date of manufacture. 7.2 When delivered in smaller bulk quantities, such as 208 liter (55 gallon) drums, the material shall be shipped in containers clearly marked with the NAVISTAR designation, name

25、of supplier, formula or code number, batch number, and date of manufacture. Markings shall be at least 25 mm (1 in) high. 8.0 DESIGNATION ON DRAWINGS Lubricant per TMS-6803 9.0 APPROVED SOURCES Shell Oil 10.0 TECHNICAL INFORMATION For further information related to the technical content of this spec

26、ification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-