GSA FED-STD-368 A-1979 QUALITY CONTROL SYSTEM REQUIREMENTS《质量控制系统设备》.pdf
《GSA FED-STD-368 A-1979 QUALITY CONTROL SYSTEM REQUIREMENTS《质量控制系统设备》.pdf》由会员分享,可在线阅读,更多相关《GSA FED-STD-368 A-1979 QUALITY CONTROL SYSTEM REQUIREMENTS《质量控制系统设备》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、FED-STD-368A December 10,1979 SUPERSEDING FED, STD. 368 July 27,1977 FEDERAL STANDARD QUALITY CONTROL SYSTEM REQUIREMENTS This standard was approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal agencies. 1. SCOPE. This standard establishes
2、minimum requirements for a quality control system to be provided and maintained by a contractor under Government contract for furnishing supplies or services. The contractors quality control system shall include the methods, procedures, controls, records, and maintenance of the system to provide ver
3、ification of product compliance with contract requirements. The extent of this system shall depend on the complexity of the item under contract. A written description of this system shall be prepared by the contractor and shall be available to the Government. The contractors quality control system s
4、hall be reviewed by the Government and is subject to the disapproval of the Government representative when the contractors procedures will not accomplish their objective. 1.1 Application. This standard is applicable when referenced in the contract. It is also applicable at supplier locations where G
5、overnment inspection at these points is required. In such cases, it is the contractors responsibility to invoke the use of this standard by his supplier. 2. REFERENCED DOCUMENTS None. 3. DEFINITIONS. As used herein, the following definitions shall apply: 3.1 Inspection. A process of examining, testi
6、ng, measuring and otherwise comparing products and services to An overall system of activities, including inspection, whose purpose is to provide a determine compliance with specified requirements. quality of product or service that meets contract requirements. 3.2 Quality control. 3.3 Statistical q
7、uality control. Quality control in which statistical techniques are used. These techniques include the use of frequency dis tribution, measure of central tendency and dispersions, control charts, acceptance sampling, regression analysis, tests of significance. 4. REQUIREMENTS. The contractor shall p
8、rovide and maintain a documented quality control system which will ensure that the end products (supplies or services) and associated components, spare parts, manuals, packing, packaging, marking, and any other contractual requirements, offered to the Government conf orm to contract requirements whe
9、ther manufactured or processed by the contractor or procured from subcontractors or vendors. It shall be available for review by the Government prior to the start of production and during the life of the contract. It shall provide control over all phases of production from the initiation of design t
10、hrough manufacture and preparation for delivery. 5. DETAILED REQUIREMENTS. 5.1 The contractor shall perform all examinations and tests to substantiate conformance to specifications, using his own or any other inspection facilities or services acceptable to the Government, before offering to the Gove
11、rnment for acceptance. 5.2 Organization. 5.2.1 Personnel performing quality control functions shall be identified and given sufficient well-defined responsibility, authority, and the organizational freedom to identif y and evaluate quality problems, and to initiate, recommend, or provide solutions.
12、5.2.2 Management shall regularly review the status and adequacy of the quality organization and conformance to the quality control system. FSC MISC THIS DOCUMENT CONTAINS .3 PAGE$. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L FED-STD-3bA HI H 97
13、77777 0005675 b H _. - FED-STD-368A 5.3 Inspection status. The contractor shall keep raw material, parts, partially assembled products, and end products segregated in accordance with their inspection status, such as accepted, rejected, set aside for rework, awaiting decision, to prevent intermixing
14、and unauthorized use. The indication of the inspection status may be accomplished by tags, labels, marking, or other positive means. 5.4 Measuring and test equipment. 5.4.1 The contractor shall have all measuring and testing equipment required to perform testing for all characteristics called for in
15、 the contract, or shall have firm arrangements with another inspection and testing facility acceptable to the Government. 5.4.2 Measuring devices, test equipment, gages, jigs, fixtures, shall be inspected at scheduled intervals against specified, certified, or otherwise valid means to ensure continu
16、ed accuracy. 5.5 Sampling plan. Statistical sampling is generally specified in the applicable product speciications. These are minimum requirements. The contractor may use other statistical sampling techniques; e.g., control charts, frequency distribution, tests of significance; whenever such sampli
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GSAFEDSTD368A1979QUALITYCONTROLSYSTEMREQUIREMENTS 质量 控制系统 设备 PDF

链接地址:http://www.mydoc123.com/p-782525.html