GMW GMW16994-2013 Double Vision Inspection Procedure For Windshields Issue 1 English [Replaced GMNA GM9628P GMNA GM9628P].pdf

《GMW GMW16994-2013 Double Vision Inspection Procedure For Windshields Issue 1 English [Replaced GMNA GM9628P GMNA GM9628P].pdf》由会员分享，可在线阅读，更多相关《GMW GMW16994-2013 Double Vision Inspection Procedure For Windshields Issue 1 English [Replaced GMNA GM9628P GMNA GM9628P].pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW16994 Double Vision Inspection Procedure For Windshields Copyright 2013 General Motors Company All Rights Reserved December 2013 Page 1 of 4 1 Scope Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of con

2、flict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. This document is the GM Worldwide Glazing Testing Standard. Its purpose is to establish a common test methodology for Glazing Materials to ensure that a high quality world class system is consis

3、tently developed and produced. This standard describes the test method used to inspect for double vision in automotive windshields. This is a living document and any suggestions or revisions will be reviewed and/or updated annually by the Fixed Glass Global Subsystem Leadership Team (GSSLT). 1.2 For

4、eword. This is a component/subsystem test. 1.3 Applicability. This standard is applicable for all passenger vehicles, multipurpose passenger vehicle (MPV), and truck models with heated grid elements in fixed glass and produced by GM worldwide. 2 References Note: Only the latest approved standards ar

5、e applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. GMW3600 2.3 Additional References. GM Security Guidelines Subsystem Technical Specifications (SSTS) 3 Resources 3.1 Facilities. 3.1.1 Calibration. The test facilities and equipment s

6、hall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.2 Equipmen

7、t. 3.2.1 A light box consisting of a 25 W light source mounted behind a No. 3480 Corning yellow-red glass or equivalent. 3.2.2 A 12.7 mm diameter light aperture positioned at the front of the light box. Centered on the aperture is a 102 mm diameter circle. 3.2.3 Test shall be performed in a dimly li

8、t room. See Figure 1 for test setup. 3.3 Test Vehicle/Test Piece. Test samples shall be of production intent design and material for design validation (DV); or, production intent design and materials manufactured with production processes (home line) for product validation (PV). Any changes to the c

9、omponents or material, e.g., design, fit, form, function, properties, manufacturing process, and/or location of manufacture require revalidation. GM shall approve Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking per

10、mitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16994 Copyright 2013 General Motors Company All Rights Reserved December 2013 Page 2 of 4 validation methods for product/process changes before the supplier is committed to the change. Refer to GMW3600. 3.4 Test Time. Calendar

11、 time: 1 day Test hours: 8 hours Coordination hours: 4 hours 3.5 Test Required Information. Review GM Security Guidelines. Note: The supplier shall work with the GM Design Responsible Engineer to comprehend this requirement. 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. 4.2 Cond

12、itions. All conditions specified shall be targeted toward the specified value with any given tolerance () used to compensate for variation. During testing, conditions specified shall not be readjusted within the tolerance unless it is to maintain the particular test condition within the specified to

13、lerance. If such an adjustment is made, it shall be approved by the appropriate GM engineer prior to the start of any testing. Unless otherwise specified, perform the tests in the as received condition without any special pre-conditioning. 4.2.1 Environmental Conditions. The following conditions app

14、ly to all tests unless otherwise specified: Temperature: +23 C 3 C. Humidity 20% to 70% unless otherwise specified. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, rep

15、orts, etc. 4.3 Instructions. 4.3.1 Position the windshield at the specified installation angle with the horizontal centerline parallel to the target and normal to the observers line of sight. 4.3.2 The light box should be positioned 7.6 m away from the windshield with the aperture located in the lin

16、e of sight according to Figure 1. 4.3.3 From a position 600 mm behind the drivers eye position the observer, using one eye only, evaluates any shift of the secondary image of the 12.7 mm dot. 4.3.4 The step described in 4.3.2 is repeated for the passenger side of the vehicle. Figure 1: Windshield Do

17、uble Vision Standard Setup Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16994 Copyright 2013 General Motors Company All Rights Reserve

18、d December 2013 Page 3 of 4 5 Data 5.1 Calculations. Not applicable. 5.2 Interpretation of Results. Acceptance Criteria: There is only one secondary image. The entire secondary image is with in the 102 mm diameter circle. Figure 2 identifies interpretation of the results. Figure 2: Interpretation of

19、 Results 5.3 Test Documentation. Record all test results and include in the test report. Include photographs of the test setup and the individual test results. The Supplier shall write evaluation reports to document the results of all validation activities and shall make the test results and evaluat

20、ion reports available to GM Engineers upon request. See GMW3600. All test reports are to be in English. The following is also required for ALL test reports: Procedure number and section numbers on all test reports. Requirement being met and Subsystem Technical Specification (SSTS) requirement number

21、. All test parameters for environment and equipment. Any authorized deviations to the plan. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the us

22、er of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. 5-Phase document: Supplier to use current approved 5-Phase to be provided by GM Product Engineering. 5-Phase to include at a minimum:

23、 1. Issue Description. 2. Root Cause Analysis. 3. Containment. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16994 Copyright 2013 Gener

24、al Motors Company All Rights Reserved December 2013 Page 4 of 4 4. Implementation. 5. Evaluation/Validation. 7.2 Acronyms, Abbreviations, and Symbols. DRE Design Release Engineer DV Design Validation GSSLT Global Subsystem Leadership Team IR Infrared MPV Multipurpose Passenger Vehicle PV Product Val

25、idation SSTS Subsystem Technical Specification SVE Subsystem Validation Engineer VTS Vehicle Technical Specification 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW16994 9 Release and Revisions This standard was originated in June 2013. I

26、t was first approved by the Fixed Glass GSSLT in November 2013. It was first published in December 2013. Issue Publication Date Description (Organization) 1 DEC 2013 Initial publication. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-