GMW GMW16803-2012 Non-carpet Floor Covering Materials Issue 1 English.pdf
《GMW GMW16803-2012 Non-carpet Floor Covering Materials Issue 1 English.pdf》由会员分享,可在线阅读,更多相关《GMW GMW16803-2012 Non-carpet Floor Covering Materials Issue 1 English.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW16803 Non-carpet Floor Covering Materials Copyright 2012 General Motors Company All Rights Reserved July 2012 Originating Department: North American Engineering Standards Page 1 of 9 1 Scope 1.1 Material Description. This standard describes
2、plastic materials that are suitable for non-carpeted floors, as well as for floor mat applications. Testing shall be performed on production intent parts. 1.1.1 Material Identification. Type I: Polypropylene Type II: Thermoplastic olefin (TPO) film on substrate Type III: Polyurethane Type IV: Rubber
3、 Type V: Ethylene-vinyl acetate (EVA) film on substrate Type VI: Polyvinyl chloride (PVC) (only for Asian markets) 1.2 Symbols. The code defines the material construction and will be assigned by the responsible department. 1.3 Typical Applications. Suitable for non-carpet floor applications, 1.4 Rem
4、arks. For requirements for vehicles without solar absorbing glass, contact the appropriate Materials Engineer. All interior materials are developed to be used in vehicles with solar glass; therefore, performance may be compromised if used in non-solar glass vehicles. 2 References Note: Only the late
5、st approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. FMVSS 302 ISO 527 ISO 105-A02 ISO 5084 ISO 105-A03 ISO/IEC 17025 ISO 105-B06 2.2 GM Standards/Specifications. GMW3059 GMW3417 GMW3116 GMW6992 GMW3182 GMW14102 GMW3205 GMW14108 GMW3208 GMW14124 GMW
6、3221 GMW14130 GMW3232 GMW14162 GMW3235 GMW14444 GMW3259 GMW14722 GMW3402 GMW15634 2.3 Additional References. TMC003 Material Safety Data Sheet guidance documents (available at ). 3 Requirements 3.1 Requirements on Test Specimens. Reference GMW3221. 3.1.1 Test Data. Lab testing shall be performed by
7、a laboratory that conforms (meets requirements but may not be formally recognized by a third party) to ISO/IEC 17025 and is acceptable to the responsible GM Department. Test reports must conform to ISO/IEC 17025. Supplier shall submit a letter of compliance. 3.1.2 Material Construction Specification
8、. All required information shall be reported on the Construction Specification Data Form provided by the Materials Engineer (see Appendix B). A form shall be submitted along with each material submitted for engineering approval. Established values for a construction will be reported on and controlle
9、d within the limits established on the Construction Specification Data Form (see Appendix B). 3.1.3 Standard Conditions (GMW3221-A). All test specimens shall be conditioned to GMW3221, Code A for a minimum of 24 h, unless the test method indicates that standard conditioning is not required or that o
10、ther conditions apply. 3.1.4 Sampling. When multiple test specimens are required, they shall be taken diagonally across the sample. Avoid taking specimens from damaged, contaminated, or defective areas caused by improper handling or manufacturing. Specimens should not be cut within 50 mm of any edge
11、 of the sample. 3.1.5 Data Reporting If all individual readings of a specific test meet or exceed the specified requirements, report the average. Unless Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted wit
12、hout license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16803 Copyright 2012 General Motors Company All Rights Reserved July 2012 Page 2 of 9 otherwise stated, any individual reading outside the specified limit does not meet the requirement. Report all individual test results that do not mee
13、t the requirements. All required information shall be reported on the appropriate test data reporting forms (see Appendix A, Data Sheets A1 and A2). 3.1.6 Visual Evaluation of Automotive Trim (GMW6992). The color, pattern, aesthetics and other related qualities shall be approved by the appropriate e
14、ngineering department as an acceptable match to the standard when viewed under conditions set forth in GMW6992 3.1.7 Deviations from Defined Test Methods. Deviations from the conditions of any test method shall have been agreed upon between supplier and vehicle manufacturer. All deviations shall be
15、specified on the component drawings, material specifications, etc. and shall be indicated on test certificates, reports, etc. 3.1.8 Documentation. Samples of components or materials released to this specification shall be tested for conformity with the requirements of this specification and approved
16、 by the responsible GM department prior to the start of delivery of production level components or materials. Any change to the component or material, e.g., design, function, properties, manufacturing process and/or location of manufacture, requires a new release of the product. It is the sole respo
17、nsibility of the supplier to provide the customer, unsolicited, with documentation of any change of modification to the product/process, and to apply for a new release. If not otherwise agreed to the entire verification test shall be repeated and documented by the supplier prior to start of delivery
18、 of the modified or changed product. In some cases a shorter test can be agreed to between the responsible GM Department and the supplier. 3.2 Construction Requirements. 3.2.1 Weight (GMW3182). Test three specimens. Report the results in grams per square meter (g/m). Refer to the Construction Specif
19、ication Data Form for weight specification requirements. 3.2.2 Thickness (ISO 5084). Refer to the construction form. Report the average for three specimens in millimeters to the nearest 0.01 mm. Use a 4.0 N load and a 200 mm 0.8 mm diameter presser foot to achieve a pressure of 0.127 kPa. All readin
20、gs should be taken after the presser foot has been in contact with the material for at least 5 s. The specimen size shall be 100 mm x 100 mm size. 3.2.3 Elongation at Break (ISO 527, Type 1A Dumbbell Test Piece Type 1A Speed 500 mm/minute). Test six specimens (three specimens from the Machine Direct
21、ion (MD) direction and another three from the Cross Machine Direction (CMD). Electronic method of calculation shall be used. Repeat testing after aging for 70 h at 70 C. No individual test results shall be less than the specified value. Refer to the Non Carpet Floor Covering Construction Specificati
22、on for the specific requirements 3.2.4 Tensile Strength (ISO 527 Type 1A dumb-bell test piece Type 1A speed 500 mm/minute) Test six specimens (three specimens from the MD direction and another three from the CMD). Electronic method of calculation shall be used. Repeat testing after aging for 70 h at
23、 70 C. No individual test results shall be less than the specified value. Refer to the Non-carpet Floor Covering Construction Specification Data Form in Appendix B for the specific requirements. 3.2.5 Cold Flexibility (GMW14108). The sample size of 25 mm x 300 mm of the material must withstand a 180
24、 degrees flex around a 25 mm mandrel at -29 C with no evidence of cracking. 3.2.6 Abrasion Resistance (GMW3208) Three specimens shall be tested according to GMW3208, CS10 wheels, 500 g load, 800 cycles. No objectionable color contrast shall be visible following 100 cycles. 3.2.7 Resistance to Scuffi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMWGMW168032012NONCARPETFLOORCOVERINGMATERIALSISSUE1ENGLISHPDF

链接地址:http://www.mydoc123.com/p-757870.html