GMW GMW15625-2011 Adhesive Application Approval Requirements Issue 2 English《粘合用批准要求 第2次出版(英文版本)》.pdf

《GMW GMW15625-2011 Adhesive Application Approval Requirements Issue 2 English《粘合用批准要求 第2次出版(英文版本)》.pdf》由会员分享，可在线阅读，更多相关《GMW GMW15625-2011 Adhesive Application Approval Requirements Issue 2 English《粘合用批准要求 第2次出版(英文版本)》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW15625 Adhesive Application Approval Requirements Copyright 2011 General Motors Company All Rights Reserved June 2011 Originating Department: North American Engineering Standards Page 1 of 7 1 Scope 1.1 Material Description. This specificatio

2、n describes the process and requirements for obtaining GM Adhesive Application Approval (AAA) for components or assemblies that contain adhesive bonds, structural and non-structural. 1.2 Symbols. Not applicable. 1.3 Typical Applications. Adhesive materials include; thermosetting polymeric liquids an

3、d pastes, pressure sensitive films and tapes, hot-melts, and solvent/water based contact cements. 1.3.1 Applicability. Not all bonding applications will require approval. Only those applications that list this specification on the drawing requirements shall require approval. 1.4 Remarks. AAA is requ

4、ired for Production Part Approval Process (PPAP) in accordance with the latest revision level of this standard. 1.5 Approvals are specific to the substrate/adhesive combination and to the facility where the adhesive application is performed. 2 References Note: Only the latest approved standards are

5、applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO/IEC 17025 ISO/TS 16949 2.2 GM Standards/Specifications. GMW3041 GMW15671 GMW3059 GMW15921 GMW3221 GMW16016 GMW14874 GMW16183 GMW14892 GMW16195 GMW15200 GMW16232 2.3 Additional References. TMC003 Material Safety Data Sh

6、eet guidance documents (available at ). 3 Requirements 3.1 Testing Requirements. Perform AAA testing as indicated in Table A1. 3.1.1 For AAA testing, all testing shall be performed in a laboratory accredited to ISO/IEC 17025. Laboratories meeting the requirements of ISO/TS 16949 can be used with the

7、 consent of GM Materials Engineering. 3.1.2 All testing is the responsibility of the GM supplier that supplies a component containing an adhesive application. 3.1.3 Final AAA will be based on the results of testing performed on production parts for each combination of substrate, adhesive and manufac

8、turing location. Tests may be performed on surrogate parts or plaques, only when approved in advance by GM Materials Engineering. 3.1.4 All samples for testing shall be obtained from parts that have been created using production intent materials and processes at the part/component build locations th

9、at will be used for manufacturing production Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15625 Copyright 2011 General Motors Company

10、All Rights Reserved June 2011 Page 2 of 7 parts. For some plastic substrate materials, if regrind is allowed, all specimens for testing must be obtained from production parts that are made from the maximum allowable regrind as stated on the drawing. 3.1.5 All materials used in the bond joint includi

11、ng substrates, paint, coatings, adhesion promoters and adhesives shall have been qualified and approved to the appropriate GM specifications. 3.1.6 All cure/activation schedules are to be those of the production system and must agree with the adhesive manufacturers recommendations. 3.1.7 Test Review

12、. When testing is completed, the tested components will be reviewed by the responsible GM Materials Engineer. 3.1.8 Test Conditions. Tests shall be conducted using the latest issue of the test methods indicated in Table A1. Suitable precautions should be taken to ensure that applicable safe limits a

13、re not exceeded when conducting test procedures, processes and/or handling the materials required by this specification. 3.2 Requirements on Test Specimens. Reference GMW3221. 3.2.1 Sample Conditioning. Unless otherwise specified, bonded samples shall be subjected to testing after a minimum aging pe

14、riod of 72 h following the curing/activation cycle. A shorter aging period may be used with approval of the appropriate GM Engineer. 3.2.2 Safety. This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated wi

15、th its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 3.2.3 All tested samples shall be retained by the supplier for review by the appropriate GM Materials Enginee

16、r at least until AAA is obtained. 3.3 Changes in Processing. 3.3.1 Notification. It is the sole responsibility of the supplier to provide the customer, unsolicited, with documentation of any change or modification to the product/process, and to apply for a new AAA release using the form in Table A3.

17、 3.3.2 Process Changes. After the initial AAA has been established, any change in processing parameters as recorded on the Adhesive Bonding Process Data Sheet (Table A2), requires evaluation with the responsible GM Materials Engineer. 3.3.3 Revalidation. If not otherwise agreed to, the entire AAA pr

18、ocess shall be repeated and documented by the supplier prior to the start of delivery of the modified or changed product. In some cases, a shorter test protocol can be agreed to between the responsible GM department, GM Materials Engineer and the supplier. 3.4 Test Results. Test reports shall be wri

19、tten per the Requirements for Test Report in ISO/IEC 17025. A checklist of all documents required for AAA is provided in Table A4. 3.5 Deviations from this Standard. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawi

20、ngs, test certificates, reports, etc. 4 Manufacturing Process Not applicable. 5 Rules and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the English an

21、d domestic language, the English language shall take precedence. 5.3 Inspection and Rejection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by the responsible Engineering de

22、partment prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. Copyrig

23、ht General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15625 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 3 of 7 It is the

24、responsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier

25、prior to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Initial Source Approval. No shipments shall be made by any supplier until representative initial production sam

26、ples have been approved by the appropriate Materials Engineering department(s) as meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition of an existing product has occurred,

27、a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in

28、 compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 6 Approved Sources Engine

29、ering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials File (i.e., GM Supply Power) under this standard number have been qualified by Engineering as meeting the requirements of this standard. For other GM locations, the responsible Engineer

30、ing group should be contacted to obtain the approved source in that individual country. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. AAA Adhesive Application Approval GHS Globally Harmonized System MSDS Material Safety Data Sheet PPAP Production Part Approval Proce

31、ss PSA Pressure Sensitive Adhesive SDS Safety Data Sheet 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Material per GMW15625 9 Release and Revisions This standard was originated in June 2007. It was first approved by the Global Adhesives Team in Ju

32、ne 2008. It was first published in June 2008. Issue Publication Date Description (Organization) 1 JUN 2008 Initial publication. 2 JUN 2011 Added Tables to Appendix A. (Adhesives GSSLT) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduc

33、tion or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15625 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 4 of 7 Appendix A Table A1: GM AAA Testing Requirements Adhesive Bond Type Testing Specification 1. Interior GMW14892 2. Stat

34、ionary Glass Bonding GMW3041 3. Moveable Glass Clips/Sash GMW16016 4. Pressure Sensitive Adhesive (PSA) Foam Tape Attachment GMW15671 5. Plastic Claddings for Wheels GMW16232 6. Metal Bonding GMW15200 7. Polymer Composite Bonding GMW15921 8. Plastic Bonding GMW16183 9. Metal Bonding Anti-Flutter GMW

35、14874 10. Roof Ditch Clip Attachment GMW16195 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15625 Copyright 2011 General Motors Company

36、 All Rights Reserved June 2011 Page 5 of 7 Table A2: Adhesive Bonding Process Data Sheet Enter applicable data and submit with the test report. Vehicle Usage Coating 2 Applied to: Substrate 1 Substrate 2 Vehicle Name: Material Supplier: Model Year: Product Code: Part Description: GM Specification: P

37、art Name: Coating 3 Applied to: Substrate 1 Substrate 2 Part Number: Material Supplier: Supplier: Product Code: Bonding Location GM Specification: Company: Bonding Process Substrate Preparation DUNS Number: Scuff Sand Grit #:_ Substrate 1 Substrate 2 Contact Name: Dry Wipe:_ Substrate 1 Substrate 2

38、Contact Number: Solvent Wipe:_ Substrate 1 Substrate 2 Materials Substrate 1 Pressure Wash:_ Substrate 1 Substrate 2 Material Supplier: Wash Chemical Supplier: Product Code: Product Code: GM Specification: GM Specification: Materials Substrate 2 Plasma/Flame Applied to: Substrate 1 Substrate 2 Mater

39、ial Supplier: Equipment Type: Product Code: Distance to Part: GM Specification: Flame Travel Speed: Materials Adhesive Solvent/AdPro Flash Time: Supplier: Bonding Process Joining Product Code: Bonding Fixture: GM Specification: Bond Gap Tolerance: _mm to _mm Materials Adhesion Promoter Bond Width: _

40、mm to _mm Material Supplier: Bonding Temperature: Product Code: Cure Time: GM Specification: Clamp Pressure: Applied to: Substrate 1 Substrate 2 Clamp/Fixture Time: Materials Coatings Tape Lamination Pressure: Coating 1 Applied to: Substrate 1 Substrate 2 Number of Passes: Material Supplier: Wet Out

41、 Percent (%): Product Code: Cooling or Dwell Time: GM Specification: Holding Racks: Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15625

42、 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 6 of 7 Table A3: AAA Request Form Section 1 Date:_ This AAA Request Form is to be completed by the Part Supplier for authorization prior to AAA testing. Procedure to complete the AAA Request Form: 1. For an initial application

43、 approval or for a proposed change, contact the responsible GM Material Engineer and the required GM stakeholders. 2. List the required GM stakeholders (as required by the GM Material Engineer) in Section 2. 3. Complete the form and send it to the GM stakeholders listed in Section 2. 4. Have the GM

44、stakeholder listed in Section 2 indicate support status and sign. 5. Send the completed and (signed) document to the GM Material Engineer for authorization. Company Name:_ Requestor Name:_ Job Title:_ Phone Number:_ FAX Number:_ Part Number (Less Finish):_ Date the supplier plans to implement the pr

45、oposed system into production:_ Initial Application or Change to existing application AAA Number: If this is a change, indicate the reason for the change. Cost Saving Improved Quality Other If this is a cost saving, was supporting documentation sent to the GM Buyer? Yes No If this is a quality impro

46、vement, was supporting data sent to GM Engineering? Yes No If other, describe: Section 2 GM Stakeholders Contacted GM Stakeholders GM Department Required to Contact Phone Number Signature Date Approved (Yes/No) Material Engineer Design Release Engineer Supplier Quality Engineer Buyer Validation Engi

47、neer The proposed AAA Request Form was reviewed by the responsible GM Engineer, authorizing the supplier to conduct AAA testing for submission. Reviewed by:_Date:_ Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15625 Copyright 2011 General Motors Company All Rights Reserved June 2011