GMKOREA EDS-T-7506-2006 THE TEST METHOD FOR DETERMINING THE MOISTURE CONTENT OF PLASTIC COMPONENTS (VERSION 3).pdf

《GMKOREA EDS-T-7506-2006 THE TEST METHOD FOR DETERMINING THE MOISTURE CONTENT OF PLASTIC COMPONENTS (VERSION 3).pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-7506-2006 THE TEST METHOD FOR DETERMINING THE MOISTURE CONTENT OF PLASTIC COMPONENTS (VERSION 3).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards THE TEST METHOD FOR DETERMINING THE MOISTURE CONTENT OF PLASTIC COMPONENTS EDS-T-7506 ISSUED DATE: 1990. 07. 11 REVISED DATE: 2006. 06. 19 VERSION: 3 EDS-T-7506THE TEST METHOD FOR DETERMINING THE MOISTURE CONTENT OF P

2、LASTIC COMPONENTS PAGE: 1/2 ISSUED DATE: 1990. 07. 11 REVISED DATE: 2006. 06. 19 VERSION: 3 GM DAEWOO Auto & Technology 1. PURPOSE Some plastic components (made from polyamide) shall contain moisture for the purpose of suitable material properties and dimensional stability, after manufacturing compo

3、nents shall be absorbed the moisture by suitable means and the moisture content shall be determined for routine quality control of components. 2. SCOPE This standard is applied to test method for determining the moisture content of plastic components. 3. DEFINITION 3.1. Moisture content: To be the m

4、ass loss of a test piece resulting from heating for 48 hours at 105. 4. TEST PIECE 4.1. Finished parts, some sections or granules shall be used as test pieces. 4.2. For initial sample approval and arbitration purposes, at least 3 test pieces shall be tested and for routine quality control, at least

5、1 test piece. 4.3. Sample of components or material released to this specification shall be tested for conformity with the requirements of its specification and approval by GMDAT TECHICAL CENTER prior to commencement of delivery of bulk supplies. 4.4. In the event of any intentional deviation from t

6、he requirements of this specification, it is the sole responsibility of the supplier to inform the purchase of all such deviation Furthermore the supplier shall submit unsolicited samples for reapproval by GMDAT TECHNICAL CENTER prior to comments of delivery of bulk supplies. 5. CONDITIONING Test pi

7、eces shall be tested in the as received condition without special conditioning. 6. APPARATUS 6.1. Oven or chamber capable of maintaining the test temperature. 6.2. Balance accuracy to 0.5 mg. 6.3. Desiccator 6.4. Crucibles or glass beakers. EDS-T-7506THE TEST METHOD FOR DETERMINING THE MOISTURE CONT

8、ENT OF PLASTIC COMPONENTS PAGE: 2/2 ISSUED DATE: 1990. 07. 11 REVISED DATE: 2006. 06. 19 VERSION: 3 GM DAEWOO Auto & Technology 7. PROCEDURE 7.1. The test piece shall be weighed to the 0.5 mg. (Note: for granules, ones smaller than 5g in weight be tested by putting in previously dried crucibles or b

9、eakers.) 7.2. The test piece shall be heated in the oven or chamber at 105 for 48 hours. 7.3. After removal from the oven or chamber, the test piece shall be placed in a desiccator. 7.4. After 30 minutes, the test piece shall be removed from the desiccator and weighed. 8. EVALUATION The moisture con

10、tent shall be calculated as follows. W = (m2 - m1) / m2 100 W : moisture content ( % ) m1: mass of test piece after heating ( g ) m2: mass of test piece as received ( g ) 9. CODING SYSTEM On drawings, material specifications etc., the moisture content shall be indicated as follows. Moisture content EDS-T-7506 2% min. Requiremnts Test method Designation 10. REFERRENCES GME 60270 Test method for determining the moisture contents of plastic compounds OPEL 275 Test method for determining the moisture contents of plastic compounds