GMKOREA EDS-T-3901-2008 PERFORMANCE AND DURABILITY TEST OF JACKS.pdf

《GMKOREA EDS-T-3901-2008 PERFORMANCE AND DURABILITY TEST OF JACKS.pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-3901-2008 PERFORMANCE AND DURABILITY TEST OF JACKS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards PERFORMANCE AND DURABILITY TEST OF JACKS Do Not Use on New Programs. Being Replaced by GMW14337 EDS-T-3901 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 (Superceded) EDS-T-3901PERFORMANCE AND DURABIL

2、ITY TEST OF JACKS PAGE: 1/6 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 GM DAEWOO Auto & Technology Note: This standard may be applied only for current project. It is Superceded for all future projects and replaced by GMW14337 1. PURPOSE This standard aims evaluation of jack feat

3、ures, load-carrying capacity and durability features, under static stress. 2. SCOPE This standard applies to the joint wagon jack (For LEMANS & ESPERO) 3. TEST PIECES 3.1. The jack assembly is tested according to the drawing specification. 3.2. Number of test pieces 3.2.1. Static stress test : Min.

4、2. 3.2.2. Durability test : Min. 2. 4. APPARATUS 4.1. Static stress test. 4.1.1. U. T. M. (Universal Test Machine). (1) The test machine which shall be so equipped that the test pieces can be stressed with a uniform loading speed of 10 mm/min max. (2) The maximum test force can be stressed according

5、 to the drawing specification. (3) Accuracy of the force measuring : 1% of measured value. (4) Accuracy of the displacement measuring : 0.25mm 4.1.2. X-Y recorder , which plots the force-deflection variation characteristics of the test pieces. 4.1.3. Jig ASM., which mounted the jack corresponding to

6、 the respective type of vehicle. 4.2. Durability test. 4.2.1. Durability test rig.(Test rig. is consist of component of following (a) to (f). (1) Pneumatic actuator. (2) Load cell (max. 1000Kg). (3) Variable motor (Motor + Reduction gear) (4) Torque tender & torque transducer (5) Flexible drive shaf

7、t (6) The others (Each limit s/w and accessory etc.) EDS-T-3901PERFORMANCE AND DURABILITY TEST OF JACKS PAGE: 2/6 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 GM DAEWOO Auto & Technology 4.2.2. Control box 4.2.3. Amplifier & X-Y recorder 5. PROCEDURE AND EVALUATION 5.1. Static str

8、ess test 5.1.1. Test arrangements In order to come as near as possible to the reality facts on the vehicle at the test, following JIG ASM have been approved. a = 520mm X = Variable (= 100mm) F = Applied force SM= Direction of applied force Y = Height of lifting (= 250mm) Q = Test force Z = Ground cl

9、earance dimension of swivel arm (Results from the requirement that the supporter must be inclined by 10opposite to the horizontal) 5.1.2. Procedure (1) The test is performed at +15 to +35 (2) Calibrate testing machine and measuring instrument (U. T. M and X-Y recorder) (3) Adjusting of the heights o

10、f lift The jack is set up on the ground larger part of base plate and supporter of jack is inserted into the lever arm of test apparatus. Jack is brought up so far as height of lift “y“ (=250mm, see component drawings). After reaching the lift height “y“, the dimension of ground clearance of the swi

11、vel arm “Z“ is adusted and the angle of between swivel arm to EDS-T-3901PERFORMANCE AND DURABILITY TEST OF JACKS PAGE: 3/6 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 GM DAEWOO Auto & Technology supporter is fixed 10 The point for the measurement of the height of the height of li

12、ft is vertical length from lower of base plate to top of supporter.After reaching lthe lift eight “y“ the dimenen of ground clear ance of the swiuel arm “Z” is adjusted. (4) The jack is stressed with the test force(Q) with a test speed of max. 100mm/min and released again after reaching the test for

13、ce(Q). The test force(Q) is determined as follows : * NOMINAL FORCE (N) - MAX. SUPPORT FORCE (N) - 25% * TEST FORCE (Q) - NOMINAL FORCE +50% Support force that indicated on the drawing is 7800N, therfore according to above equation * NOMINAL FORCE (N) - 5850N * TEST FORCE (Q) - 8775N At the test arr

14、angements (refer to clause 5.1.1) the test force (Q) is applied by the force (F). Because the point of application of the force F. works displaced by the lever arm “X“ opposite to the test force (Q), following equation results for the calculation of the force F. * From the the test arrangements a=52

15、0mm, X=100mm APPLIED FORCE (F) = 10463N (5) Total permanent setting amount is taken from the plotted force-deflection diagram at F/2. 5.1.3. Evaluation The total setting amount of jack is defermined from the force deflection diagram as follows. The curve path shows the course of the force-deflection

16、 vartation curve of jack which was stressed with the calculated force F. At a continuous force F/2 the total permanent setting amount SMbl is taken from the plotted force -deflection diagram with this, read value the total permanent setting amount of the jack is calculated according to following equ

17、ation )(11aXaSS Mbb+=2B9B=+ EDS-T-3901PERFORMANCE AND DURABILITY TEST OF JACKS PAGE: 4/6 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 GM DAEWOO Auto & Technology (From a=520mm, X=100mm)= 1.192 SMbl 5.1.4. Requirement The total permanent setting amount on the jack (Sbl) in mm may c

18、ome to max. 2% (Max. 5mm) of the adjusted height of left 5.2. Durability test 5.2.1. Test arrangenents This test is performed on the vehicle condition or as near as possible to the same condition with the vehicle following test rig have been approved 5.2.2. Procedure (1) Load the jack with the nomin

19、al force (5850N) * NOMINAL FORCE - MAX. SUPPORTING FORCE (N) - 25% (Supporting force is indicated on the drawing : 7800N) (2) Raise the jack to its height position and apply the nominal force and operate it over the lifting range for a total of 50 applications. (3) The lifting range is 2/3 of the ex

20、tended length (=365mm) on the drawing. EDS-T-3901PERFORMANCE AND DURABILITY TEST OF JACKS PAGE: 5/6 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 GM DAEWOO Auto & Technology (4) Allow for a cooling period of 50.5 min every time the jack is in its highest position. (Lifting speed ,1

21、5050 mm/min) (5) Measure the max. operating force at the beginning of the test and for every 10thlift of the 50 lifts and record on data sheet appendix. (6) During the duravility test, the following force curve must be covered versus the lifting height (a) P3 - P2 - P1 : Lowering jack (b) P1 - P2 -

22、P3 : Lifting jack * Force - lifting length (at P1, P2, P3 Point) FORCE LIFTING LENGTH P1 2925N 122mm (1/3 MAX) P2 5850N 244mm (2/3 MAX) P3 5850N 365mm(MAX.) 5.2.3. Requirment (1) During the furability test, no damage of the jack may occur. (2) The max. operating force of 80N may not be exceeded. (3)

23、 When testing the jack may not lower from any posistion without manual assistance after lifting. EDS-T-3901PERFORMANCE AND DURABILITY TEST OF JACKS PAGE: 6/6 ISSUED DATE: 1990. 04. 09 REVISED DATE: 2008. 11. 20 VERSION: 3 GM DAEWOO Auto & Technology Appendix 1. JACK DURABILITY TEST DATA SHEET DIVISION TEST CONTENT LIFTING LOWERING FORCE OF FLEXIBLEDRIVE SHAFT INITIAL FORCE AFTER THE 10TH LIFTING AFTER THE 20TH LIFTING AFTER THE 30TH LIFTING AFTER THE 40TH LIFTING OPERATINE EFFORTS (NOMINAL VALUE N) AFTER THE 50TH LIFTING