GME QK 000407-2003 Blend from Plasticized PVC and NBR (English German)《增塑聚氯乙烯(PVC)和丁腈橡胶(NBR)的混合物 英语 德语》.pdf
《GME QK 000407-2003 Blend from Plasticized PVC and NBR (English German)《增塑聚氯乙烯(PVC)和丁腈橡胶(NBR)的混合物 英语 德语》.pdf》由会员分享,可在线阅读,更多相关《GME QK 000407-2003 Blend from Plasticized PVC and NBR (English German)《增塑聚氯乙烯(PVC)和丁腈橡胶(NBR)的混合物 英语 德语》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、MaterialSpecificationPlasticsQK 000407Blend from Plasticized PVC andNBRBlend aus Weich-PVC und NBR1 General Information 1 Allgemeine AngabenMaterial: /Werkstoff:Blend from plasticized polyvinylchloride and nitrile butadiene rubber. /Blend aus Weich-Polyvinylchlorid und Nitrilkautschuk.Symbol: /Kurzz
2、eichen: PVC+NBR Application: /Verwendung:Extrusion type for manufacturing technical parts requiring good temperatureresistance and flexibility, e.g. cover strip. /Extrusionstype zur Herstellung technischer Teile mit guterWrmeformbestndigkeit und Flexibilitt, z.B. Abdeckleiste.2 Requirements 2 Forder
3、ungen2.1 Values for Documentation. 2.1 Zu dokumentierende Eigenschaften.Properties /EigenschaftenUnit /EinheitStandard /NormDensity /Dichte 1,19 0,03 g/cm3ISO 1183Hardness /Hrte 61 3 Shore AISO 868(Note 1)Stress at Break /(Note 1)Bruchspannung12 3 N/mm2DIN 53504Standard rod S3 /Normstab S3speed/v =
4、100 mm/minAsh /Glhrckstand 12%bymass/Massenanteil in %ISO 3451(at / bei +950 C)Note 1: Values shall be determined on slabs Note 1: Werte wurden an Prfplatten ermittelt Copyright 2003 General Motors Corporation All Rights ReservedPublication Department: GME Specification CenterMarch 2003 Page 1 of 3Q
5、K 000407 ADAM OPEL AG ENGINEERING STANDARDS2.2 Only for Information. 2.2 Nur zur Information.Properties /EigenschaftenUnit /EinheitStandard /NormHardness /HrteISO 868at / bei 0 C 68 3 Shore Aat / bei -20 C 78 3 Shore A(Note 1)Strain at Break /(Note 1)Bruchdehnung350 50 %DIN 53504Standard rod S3 /Nor
6、mstab S3speed/v = 100 mm/min(Note 1)Compression Set /(Note 1)DruckverformungsrestDIN 53517(24 +0/-2) h at / bei (+70 2) C 58 %Note 1: Values shall be determined on slabs Note 1: Werte wurden an Prfplatten ermittelt3 Reference 3 Hinweis3.1 For further information refer to QK 000000 andGMW3013.3.1 Wei
7、tere Informationen siehe QK 000000 undGMW3013.3.2 All materials supplied to this specificationmust comply with the requirements of GMW3059,Restricted and Reportable Substances for Parts.3.2 Alle nach dieser Vorschrift gelieferten Werkstoffemssen die Anforderungen von GMW3059, Rege-lung ber die Zulss
8、igkeit von gefhrlichen Stof-fen, erfllen.3.3 Despite spot checks possibly performed by Opel,it is the suppliers responsibility that the deliveredparts are in line with the Opel drawings. Deliveriesof samples, first off-tool parts and parts, whose per-formance has been changed, must be accompaniedby
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMEQK0004072003BLENDFROMPLASTICIZEDPVCANDNBRENGLISHGERMAN 聚氯乙烯 PVC 丁腈橡胶 NBR 混合物 英语 德语 PDF

链接地址:http://www.mydoc123.com/p-755876.html