GME QK 000406-2003 《含玻璃纤维的硬聚氯乙烯 英语 德语》.pdf
《GME QK 000406-2003 《含玻璃纤维的硬聚氯乙烯 英语 德语》.pdf》由会员分享,可在线阅读,更多相关《GME QK 000406-2003 《含玻璃纤维的硬聚氯乙烯 英语 德语》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、MaterialSpecificationPlasticsQK 000406Rigid PVC with Glass Fibres Hart-PVC mit Glasfasern1 General Information 1 Allgemeine AngabenMaterial: /Werkstoff:Rigid polyvinylchloride with 15 % by mass glass fibres. /Hart-Polyvinylchlorid mit 15 Massenanteil in % Glasfasern.Symbol: /Kurzzeichen:PVC-GF15Appl
2、ication: /Verwendung:Extrusion type for manufacturing rigid technical parts, which are not exposeddirectly to weathering effects, e.g. insert protective moulding. /Extrusionstype zur Herstellung steifer technischer Teile, die nicht direkt derWitterung ausgesetzt sind, z.B. Einlage-Schutzzierstab.2 R
3、equirements 2 Forderungen2.1 Values for Documentation. 2.1 Zu dokumentierende Eigenschaften.Properties /EigenschaftenUnit /EinheitStandard /NormDensity /Dichte 1,47 0,03 g/cm3ISO 1183(Note 1)Ash /(Note 1)Glhrckstand 19 2%bymassMassenanteil in %ISO 3451(at / bei +950 C)(Note 1)Charpy Notched ImpactSt
4、rength /(Note 1)Charpy-Kerbschlagzhigkeit 92 kJ/m2ISO 179 / 1eAStandard small rod 2C /Normkleinstab 2CVicat Softening Temperature /Vicat-ErweichungstemperaturISO 306VST/B/50 +77 2 C(Note 1)Modulus of Elasticity by the3Point-Flexural-Test /(Note 1)Elastizittsmodul aus dem3Punkt-Biegeversuch 3800 300
5、N/mm2DIN 53457Note 1: Values shall be tested on slabs Note 1: Werte werden an Prfplatten ermittelt Copyright 2003 General Motors Corporation All Rights ReservedPublication Department: GME Specification CenterMarch 2003 Page 1 of 3QK 000406 ADAM OPEL AG ENGINEERING STANDARDS2.2 Only for Information.
6、2.2 Nur zur Information.Properties /EigenschaftenUnit /EinheitStandard /NormYield Stress /Streckspannung 35 N/mm2Yield Strain /Streckdehnung 2,9 %Stress at Break /Bruchspannung 16 N/mm2Strain at Break /Bruchdehnung 14 %DIN 53455Test piece 3 /Probekrper 3speed/v = 5 mm/minHardness /Hrte 79 3 Shore DI
7、SO 868Coefficient of Linear ThermalExpansion /Linearer thermischer Lngenaus-dehnungskoeffizient 3,5 x 10-51/KDIN 537523 Reference 3 Hinweis3.1 For further information refer to QK 000000 andGMW3013.3.1 Weitere Informationen siehe QK 000000 undGMW3013.3.2 All materials supplied to this specificationmu
8、st comply with the requirements of GMW3059,Restricted and Reportable Substances for Parts.3.2 Alle nach dieser Vorschrift gelieferten Werkstoffemssen die Anforderungen von GMW3059, Rege-lung ber die Zulssigkeit von gefhrlichen Stof-fen, erfllen.3.3 Despite spot checks possibly performed by Opel,it i
9、s the suppliers responsibility that the deliveredparts are in line with the Opel drawings. Deliveriesof samples, first off-tool parts and parts, whose per-formance has been changed, must be accompaniedby a test report showing the test results in terms offigures.3.3 Unbeschadet etwaiger durch den Abn
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMEQK0004062003 玻璃纤维 聚氯乙烯 英语 德语 PDF
