GME 8080-2012 Axial Run-out and Operating Characteristics of Toothed Belts (Revision 2 English German This standard may be applied only for current programs It is inactive for all .pdf
《GME 8080-2012 Axial Run-out and Operating Characteristics of Toothed Belts (Revision 2 English German This standard may be applied only for current programs It is inactive for all .pdf》由会员分享,可在线阅读,更多相关《GME 8080-2012 Axial Run-out and Operating Characteristics of Toothed Belts (Revision 2 English German This standard may be applied only for current programs It is inactive for all .pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Test MethodGME8080LIMITED USEAxial Run-out and OperatingCharacteristics of Toothed BeltsAxialschlag und Lauftendenz vonZahnriemenNOTE: This standard may be applied only forcurrent programs. It is inactive for all futureprojects and without replacement.HINWEIS: Diese Spezifikation darf nur noch frlau
2、fende Projekte angewendet werden und ist fralle zuknftigen Projekte ohne Ersatz ungltig.1 Scope 1 ZweckDetermination the axial run-out and the operatingcharacteristics of toothed belts for engine timing.Ermittlung des Axialschlags und der Lauftendenz vonZahnriemen des Motor-Steuertriebes.This Test M
3、ethod is applicable to all toothed belts forengine timing.Diese Test Method ist anwendbar fr alle Zahnriemender Motorsteuerung.Note: Nothing in this specification, however, super-sedes applicable laws and regulations unless a spe-cific exemption has been obtained.Hinweis: Falls keine Ausnahmen verei
4、nbart wurden,darf die Vorschrift keine anzuwendenden Gesetzeund Regelungen auer Kraft setzt.Note: In the event of a conflict between the Germanand theEnglish language,the German language shalltake precedence.Hinweis: Im Falle von Unstimmigkeiten zwischendem deutschen und dem englischen Text ist derd
5、eutsche Text ausschlaggebend.2 References 2 ReferenzenNote: Only the latest approved standards are appli-cable unless otherwise specified.Hinweis: Wenn nicht anders angegeben, ist jeweilsdie neueste Fassung gltig.2.1 External Standards/Specifications. 2.1 Externe Normen/Vorschriften.ISO 90102.2 GM S
6、tandards/Specifications. None. 2.2 GM Normen/Vorschriften. Keine.2.3 Additional References. None. 2.3 Zustzliche Referenzen. Keine.3 Test Equipment 3 PrfausrstungAccording to ISO 9010. Nach ISO 9010.4 Test Material 4 PrfwerkstoffAt least 10 toothed belts shall be tested. Es sind mindestens 10 Zahnri
7、emen zu prfen. Copyright 2012 General Motors Company All Rights ReservedPublication Department: GME Specification CenterOctober 2012 Page 1 of 6PRD045 - VPRE ST 1 10/03 GME8080 GM EUROPE ENGINEERING STANDARDS5 Test Method 5 Prfverfahren5.1 Summary of Test Method. Determination theaxial run-out and t
8、he operating characteristics oftoothed belts.5.1 Zusammenfassung des Prfverfahrens.Ermittlung des Axialschlags und der Lauftendenz vonZahnriemen.5.2 Test Sample Preparation. See appropriate testmethod.5.2 VorbereitungdesPrfteils. Sieheentsprechen-des Prfverfahren.5.3 Test Procedure. 5.3 Prfung.5.3.1
9、 Axial Run-out and Operating Characteris-tics.5.3.1 Axialschlag und Lauftendenz.5.3.1.1 Test Set-up. The test set-up shall be per-formed according to Figure 1 and Figure 2.5.3.1.1 Versuchsaufbau. Der Versuchsaufbau istentsprechend Abbildung 1 und Abbildung 2 auszu-fhren.Standardized and calibrated m
10、easuring devices shallbe used.Es sind genormte und kalibrierte Messgerte zu ver-wenden.5.3.1.2 Test Parameters. 5.3.1.2 Prfparameter.Load F: According to release drawing Beanspruchung F: Nach FreigabezeichnungSpeed n: (50 5) min-1 Drehzahl n: (50 5) min-1Pulley diameter: According to release drawing
11、 Scheibendurchmesser: Nach Freigabezeichnung5.3.1.3 Procedure. 5.3.1.3 Durchfhrung.5.3.1.3.1 Version A. 5.3.1.3.1 Version A.5.3.1.3.1.1 The toothed belt shall be inserted in themeasuring device and tensioned according to thedrawing.5.3.1.3.1.1 Der Zahnriemen ist in die Messvorrich-tung einzulegen un
12、d nach Zeichnung zu spannen.5.3.1.3.1.2 The electric motor shall be started. 5.3.1.3.1.2 Der Elektromotor wird gestartet.5.3.1.3.1.3 The axial run-out and the operating char-acteristics shall be determined and evaluated afterat least four revolutions using suitable measuringmethods.5.3.1.3.1.3 Nach
13、mindestens vier Umlufen sindder Axialschlag und die Lauftendenz mit geeignetenMessschritten zu bestimmen und auszuwerten. Copyright 2012 General Motors Company All Rights ReservedPage 2 of 6 October 2012PRD045 - VPRE ST G 10/03GM EUROPE ENGINEERING STANDARDS GME8080Figure 1: Algorithm for Run-off an
14、d LateralRun-out Measurement according to Version AAbbildung 1: Algorithmus fr Ablauf- undSeitenschlagmessung nach Version AKey to figure: ZeichenerklrungA Current run-off A aktueller AblaufB Belt width B ZahnriemenbreiteC Running direction C LaufrichtungLW Effective length LW WirklngeS Current late
15、ral run-out S aktueller SeitenschlagSS Lateral run-out SS SeitenschlagX Coordinates in measurement direction X Koordinate in MessrichtungY Coordinates in running direction of belt Y Koordinate in Riemenlaufrichtungy= B + 27 mm min. y= B + 27 mm min.Offset: 1st measured value = 0 at Y = 0 Offset: 1.
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GME80802012AXIALRUNOUTANDOPERATINGCHARACTERISTICSOFTOOTHEDBELTSREVISION2ENGLISHGERMANTHISSTANDARDMAYBEAPPLIEDONLYFORCURRENTPROGRAMSITISINACTIVEFORALLPDF

链接地址:http://www.mydoc123.com/p-754975.html