FORD WSS-M99J56-A1-2015 COATING TEMPORARY CORROSION PROTECTION EXTERIOR CHROME PLATED AND STAINLESS STEEL PARTS TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M99J56-A1-2015 COATING TEMPORARY CORROSION PROTECTION EXTERIOR CHROME PLATED AND STAINLESS STEEL PARTS TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M99J56-A1-2015 COATING TEMPORARY CORROSION PROTECTION EXTERIOR CHROME PLATED AND STAINLESS STEEL PARTS TO BE USED WITH FORD WSS-M99P1111-A .pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2015 10 02 Released C. McComb NA Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 3 COATING, TEMPORARY CORROSION PROTECTION, WSS-M99J56-A1 EXTERIOR CHROME PLATED AND STAINLESS STEEL PARTS 1. SCOPE
2、 The material defined by this specification is a temporary corrosion protection coating suitable for use on chrome plated and stainless steel parts. It is removed with soap and water. 2. APPLICATION This specification was released originally for material used to provide supplemental corrosion protec
3、tion for exterior chrome plated and stainless steel components against surface damage during transportation prior to customer delivery. 2.1 LIMITATIONS This coating provides protection for up to 6 months after application and is not intended for long term protection. Avoid overspray / incidental con
4、tact on painted or molded in color parts of the vehicle during the application of the coating. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.2 FU
5、NCTIONAL APPROVAL Materials being evaluated for approval to this specification shall be subjected to an application trial. Application trial results must be approved by the affected activity. Results shall be made available to Materials Engineering prior to material approval and release. 3.3 SAMPLE
6、PREPARATION 3.3.1 Substrate - Chrome plated and stainless steel components. Spray the surface to be coated with a 50/50 solution of isopropyl alcohol and water and wipe with a clean cloth to ensure the absence of oil or alkaline residues, fingerprints, dirt, moisture and other foreign materials. 3.3
7、.2 Application Procedure Spray the coating to the test surface to obtain a wet film thickness per 3.3.4. Spray equipment and application parameters can be obtained from the coating manufacturer. ENGINEERING MATERIAL SPECIFICATION WSS-M99J56-A1 Copyright 2015, Ford Global Technologies, LLC Page 2 of
8、3 3.3.3 Application Temperature 20 - 25 C 3.3.4 Wet Film Thickness 50 - 75 microns (FLTM BI 156-01) 3.3.5 Curing, Air Dry Dry to the touch (23 +/- 2 C and 50 +/- 5% RH) in 30 minutes 3.4 APPEARANCE AFTER ENVIRONMENTAL EXPOSURE (Allow at least 24 hours after coating application (23 +/- 2 C and 50 +/-
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM99J56A12015COATINGTEMPORARYCORROSIONPROTECTIONEXTERIORCHROMEPLATEDANDSTAINLESSSTEELPARTSTOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-754321.html