FORD WSS-M4C135-B1-2016 FUEL 91 RON UNLEADED INITIAL FILL VENEZUELA TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M4C135-B1-2016 FUEL 91 RON UNLEADED INITIAL FILL VENEZUELA TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M4C135-B1-2016 FUEL 91 RON UNLEADED INITIAL FILL VENEZUELA TO BE USED WITH FORD WSS-M99P1111-A .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2016 07 05 Activated L. Benvenutti, SA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 4 FUEL, 91 RON, UNLEADED, INITIAL FILL, VENEZUELA WSS-M4C135-B1 1. SCOPE The material defined by this specif

2、ication is a well-refined gasoline and normal commercial additives. 2. APPLICATION This specification was released originally for material used as initial fill fuel for vehicles designed to operate on gasoline in Venezuela. Additives are present to protect the fuel system. This material is not speci

3、fically intended for use in certification testing, mileage accumulation or general fueling. 3. REQUIREMENTS This material must be produced using current refinery practices for market place fuels and must meet all pertinent legal gasoline requirements in Venezuela. 3.1 STANDARD REQUIREMENTS FOR PRODU

4、CTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 OCTANE NUMBERS 3.2.1 Research 91.0 min (ISO 5164 / ASTM D2699) 3.2.2 Anti Knock Index 87.0 min (ISO 5163 / ASTM D2700) 3.3 TOTAL SULFUR 0.15% mass,

5、max (CONVENIN 1826/ ASTM D 294 / 5453 / 2622) 3.4 METAL CONTENT 3.4.1 Lead 0.0130 g/L max (ASTM D3237) 3.4.2 Phosphorus 0.0010 g/L max (ASTM D3231) 3.4.3 Manganese 0.0010 g/L max (ASTM D3831) ENGINEERING MATERIAL SPECIFICATION WSS-M4C135-B1 Copyright 2016, Ford Global Technologies, LLC Page 2 of 4 3

6、.5 COMPOSITION 3.5.1 Hydrocarbons % volume, max (ASTM D1319 / 5769 / DIN 51 791) Aromatics 35 Olefins + Aromatics 45 Saturates Report 3.5.2 Gum Content (ISO 6246 / ASTM D381) Washed 5 mg/100 mL max Unwashed Report 3.5.3 Benzene 1.2% vol max (ASTM D3606 / 5769 / EN 12177 / EN 238) 3.5.4 Total Oxygen

7、3.7% mass max (ASTM D5599 / 4815) or 2.7% mass (if ether is used) 3.6 DISTILLATION RANGE (ASTM D86-9) Volume Evaporated Temperature Initial boiling point 30 min 10% 70 C max 50% 77 121 C 90% 195 C max Final boiling point 225 C max Residue 2% volume max 3.7 VAPOR PRESSURE 3.7.1 Seasonal Geographical

8、Volatility Shall meet the local appropriate specifications. 3.8 OXIDATION STABILITY 240 minutes min (ISO 7536 / ASTM D525) 3.9 CORROSION PROTECTION 3.9.1 Copper Tarnish 1 min max (ISO 2160 / ASTM D 130, 3 h at 50 C COVENIN 872) 3.10 ODOR The material shall have the usual characteristic odor of gasol

9、ine. There shall be no obvious foreign odors. ENGINEERING MATERIAL SPECIFICATION WSS-M4C135-B1 Copyright 2016, Ford Global Technologies, LLC Page 3 of 4 3.11 APEARANCE (Visual inspection / ASTM D4176) Pink or Red dyed, clear, no free water or particulates 3.12 ADDITIVES Fuels shall contain normal co

10、mmercial additives at concentrations representative of good commercial practice in the receiving locale (unless otherwise specified). Metallic additives, including lead, manganese and phosphorus are not allowed. 3.13 CERTIFICATION Supplier shall certify that the gasoline is a formula that has been t

11、ested and meets Ford Motor Company requirements as stated in these specifications. Technical evidence of these data and manufacturing limits must be tabulated on the attached form. This certification shall be by the suppliers director of research or other authorized official and submitted to the res

12、ponsible Ford purchasing activity. This information will then be forwarded to the Materials Activity of the Engine Product Engineering Office or to the product engineering office responsible for source approval. 4. GENERAL INFORMATION The information given below is provided for clarification and ass

13、istance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 FLAMMABILITY This material represents a potential fire hazard. The Manufacturing Engineering Department or other responsible activity shall notify both the Security a

14、nd Safety Units of its presence to assure that proper fire precautions are provided. The location in which it is used or stored shall be included in the notifications. 4.2 SAMPLING AND SUBMISSION OF SAMPLES (ISO 3170 / 3171, ASTM D4057 / D4177) Quality control records must be made available to Fuels

15、 and Lubricants Engineering upon request. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATION WSS-M4C135-B1 Copyright 2016, Ford Global Technologies, LLC Page 4 of 4 Company _ Terminal _ Volatility Grade _ Specification _ Date _ Inspection Results Specification Typical Manufacturing Limits Ap

16、pearance Clean and free of Impurities _ _ Research Octane Number 91.0 min _ _ Anti Knock Index 87.0 min _ _ Lead, g/L 0.0130 max _ _ Manganese, g/L as MMT 0.0010 max _ _ Phosphorus, g/L 0.0010 max _ _ Total Sulfur, %mass 0.15 max _ _ Copper Corrosion, 3h at 50 C 1 max _ _ Oxidation Stability.100 C 2

17、40 min _ _ Vapor Pressure, kPa Report _ _ Specific gravity at 20 C Report _ _ Distillation Range Initial Boiling Point, C 30 min _ _ 10% Evaporated, C 70 C max _ _ 50% Evaporated, C 77 - 121 C _ _ 90% Evaporated, C 195 C max _ _ Final Boiling Point, C 225 C max _ _ Residue, % vol 2 max _ _ Hydrocarb

18、ons, % vol Aromatics 35 max, _ _ Olefins + Aromatics 45 _ _ Saturates Report _ _ Benzene, % vol 1.2 max _ _ Oxygen, %mass (1) 3.7 max _ _ Gum, mg/100 ml washed 5 _ _ Gum, mg/100 ml unwashed Report _ _ Water and Sediments, % mass 0.01 max _ _ Additives Type & Formula Manufacturing Limits Anti-oxidant _ _ Anti-corrosion _ _ Detergent _ _ Metal Deactivator _ _ Miscellaneous _ _ (1) In case of Ether addition, the Oxygen limit decreases to 2.7% mass. Signature_ Title_