FORD WSS-M3H105-A10-2008 CARPET POLYESTER FLAT NEEDLED LATEX BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《乳胶背涂的聚酯扁平针刺地毯 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M15P32-C]》.pdf
《FORD WSS-M3H105-A10-2008 CARPET POLYESTER FLAT NEEDLED LATEX BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《乳胶背涂的聚酯扁平针刺地毯 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M15P32-C]》.pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M3H105-A10-2008 CARPET POLYESTER FLAT NEEDLED LATEX BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《乳胶背涂的聚酯扁平针刺地毯 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSS-M15P32-C]》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions Rev. 2 2008 11 03 N-STATUS Replaced by WSS-M15P32-C L. Sinclair, FNA 2000 09 08 Activated M. Dumitrescu Printed copies are uncontrolled Page 1 of 3 Copyright 2008, Ford Global Technologies, Inc. CARPET, POLY
2、ESTER, FLAT NEEDLED, WSS-M3H105-A10 LATEX BACKCOATED NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a flat needled, polyester, non-woven carpet of good quality and uniform composition backcoated a with synthetic latex. 2. APPLICATION This specification was origi
3、nally released for material used in the luggage compartment as a cover back trim lower product for the 2000 Ford Focus. The application requires stiffness as well as uniformity of the luggage compartment face material. 3. REQUIREMENTS Material specification requirements are to be used for initial qu
4、alification of materials. In addition to the requirements listed herein, the end-item carpet assembly (molded or otherwise fabricated) shall meet all requirements of the WSS-M15P32-C performance specification. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to the
5、Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and t
6、hermograms that correspond to the reference standard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior t
7、o testing and tested under the same conditions unless otherwise specified. ENGINEERING MATERIAL SPECIFICATION WSS-M3H105-A10 Page 2 of 3 Copyright 2008, Ford Global Technologies, Inc. 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from production representative carpe
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM3H105A102008CARPETPOLYESTERFLATNEEDLEDLATEXBACKCOATEDTOBEUSEDWITHFORDWSSM99P1111A 乳胶 聚酯 扁平 针刺

链接地址:http://www.mydoc123.com/p-753261.html