FORD WSS-M2C913-B-2004 OIL ENGINE INITIAL AND SERVICE FILL SAE 5W-30 TO BE USED WITH FORD WSS-M99P1111-A 《SAE 5W-30初始注入和运行中注入发动机油 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSS-M2C913-B-2004 OIL ENGINE INITIAL AND SERVICE FILL SAE 5W-30 TO BE USED WITH FORD WSS-M99P1111-A 《SAE 5W-30初始注入和运行中注入发动机油 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M2C913-B-2004 OIL ENGINE INITIAL AND SERVICE FILL SAE 5W-30 TO BE USED WITH FORD WSS-M99P1111-A 《SAE 5W-30初始注入和运行中注入发动机油 与标准FORD WSS-M99P1111-A一起使用 》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2004 08 31 Revised Inserted 3.0; Revised 2; Deleted 3.10 Report values - “NIL“ or Trace“ are not permissible S _ _ _ _ _ P _ _ _ _ _ Zn _ _ _ _ _ Ba _ _ _ _ _ Ca _ _ _ _ _ Mg _ _ _ _ _ Na _ _ _ _ _ N _ _ _ _ _ B _ _ _ _ _ Cu _ _ _ _ _ Cl _ _ _

2、 _ _ Sulfated Ash _ _ _ _ _ V. Tests Conducted _ _ _ _ _ Comments: _ _ _ _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C913-B Printed copies are uncontrolled Copyright 2004, Ford Global Technologies, LLC Page 11 of 13 (Supplement A, p. 7 of 7) Oil Company_ Date_ Product Name_ Product

3、 Code_ Specification Test Mfg. Physical/Chemical Properties Requirements Results Limits Viscosity at 150 C (ASTM D 445), mm2/s report _ _ Viscosity at 100 C (ASTM D 445), mm2/s 9.3-.001%) report _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C913-B Printed copies are uncontrolled Copy

4、right 2004, Ford Global Technologies, LLC Page 13 of 13 (Supplement B, p. 1 of 1) Oil Company_ Date_ Product Name_ Blend Location _ Product Code_ Quality Control Certification Physical/Chemical Properties Approved Limits Frequency Viscosity at 150 C (ASTM D 445), mm2/s _ _ Viscosity at 100 C (ASTM D

5、 445), mm2/s _ _ Viscosity at 40 C (ASTM D 445), mm2/s _ _ Density (ASTM D 1298), kg/L _ _ Viscosity at 25 C (ASTM D 5293), mPa.s _ _ Viscosity at 30 C (ASTM D 5293), mPa.s _ _ Low Temp. Pumping Viscosity at -30C, mPa.s _ _ (ASTM D 4684) at -35C, mPa.s _ _ Pour Point (ASTM D 97), C _ _ Stable Pour P

6、oint (SAE J 300 App. B), C _ _ Gelation Index (ASTM D 5133) _ _ Flash Point (ASTM D 93), C _ _ Volatility Evap. Loss, 1 h at 250C (ASTM D 5800), % _ _ Shear Stability (ASTM D 445), mm2/s at 100 C After ASTM D 3945 or CEC L-14-A-93 _ _ After 10 h in “L-38 or Sequence VIII“ Test _ _ Viscosity at 150 C

7、 and 106s-1 (ASTM D 4683 or CEC L-36-A-97), mPa.s New Oil _ _ After ASTM D 3945 or CEC L-14-A-88 _ _ Copper Corrosion (ASTM D 130, 3 h at 100 C) _ _ Filterability (FLTM BJ 124-01), % _ _ Water Tolerance (Modified FLTM BJ 124-01), % _ _ Foaming (ASTM D 892) without Option A Sequence I, mL _ _ Sequenc

8、e II, mL _ _ Sequence III, mL _ _ High Temperature Foaming (ASTM D6082), mL _ _ Total Acid Number (ASTM D 664), mg KOH/g _ _ Total Base Number (ASTM D 2896), mg KOH/g _ _ Sulfated Ash (ASTM D 874), % _ _ Phosphorus content, % _ _ Barium, % _ _ Boron, % _ _ Calcium, % _ _ Chlorine, % _ _ Copper, % _ _ Magnesium, % _ _ Molybdenum, % _ _ Nitrogen, % _ _ Potassium, % _ _ Silicon, % _ _ Sodium, % _ _ Sulfur, % _ _ Zinc, % _ _ Other (.001%) _ _ Signature_ Title_ Materials Engineering Concurrence_